Page 1
K1
K SERIES
K2
-Series amplifi ers deliver more power
and sound while using less energy than
conventional amplifi ers. And it’s all in a
K
durable, maintenance-free package that’s just
two rack spaces high.
Using patented Balanced Current Amplifi er
®
(BCA
) circuitry, Crown® K-Series amplifi ers
give you massive amounts of power while generating just one-tenth the heat of conventional
amplifi ers. In fact, the powerful K2
can deliver an amazing 1,250 watts per channel
into 2 ohms (and that’s a very solid 2 ohms)!
Because of their incredible effi ciency, K-Series
amplifi ers require no internal cooling fan
and feature a closed chassis. Of course, no
fan means no fan noise. In addition, the
closed chassis makes these amplifi ers virtually
immune to environmental problems such as
dust, cigarette smoke, stage fog and spilled liquids. In practical, everyday terms, the K-Series
amplifi ers are essentially maintenance-free. As
with all convection-cooled amplifi ers, varying
operating levels and loads may require additional air movement in high ambient temperature conditions.
K-Series amplifi ers are so energy effi cient—
more than twice that of conventional switching
amps—they require signifi cantly less energy to
deliver their massive power into virtually any
load, no matter how diffi cult. In addition, each
amplifi er is equipped with a “green” circuit
that further reduces energy use during idle
periods. Energy draw is so low—only 12 watts
or less—the amplifi er may be kept in a continual ready state at minimal cost. This effi ciency means you’ll realize signifi cant savings
over the life of the amplifi er, reducing the
cost of ownership, as well as enabling more
K-Series amplifi ers to be plugged into a single
AC circuit, reducing installation costs.
®
amplifi er
Features
• Accurate, uncolored sound with very low
distortion for the best in music and voice
reproduction
• High damping factor for tight, clean bass
response
• Advanced design for energy conservation
• Mono mode switches allow you to set up your
amps/speakers in the confi guration that best
suits your needs—with combined amp inputs,
combined amp outputs, or both.
• Advanced protection circuitry guards against:
shorted outputs, open circuits, DC, mismatched loads, general overheating,high-frequency overloads and internal faults
• Extremely versatile, handling a wide range of
speaker impedances and outputs
Best of all, the K Series delivers all of the superior sound that Crown is known for—tight,
chest-slamming low end, crystal-clear highs
and a well-defi ned midrange. Several exceptional product reviews concur that the K Series
delivers fantastic sound.
The K Series stands above the rest as the performance leader in convection-cooled designs.
For more details about the Crown K Series,
contact the Crown Technical Support Group at
800-342-6939 or 574-294-8200. Also, visit the
Crown Audio website at www.crownaudio.com.
Specifi cations
The following applies to 120-VAC, 60-Hz units in Stereo mode
with 8-ohm loads and an input sensitivity of 26 dB gain
unless otherwise specifi ed. Specifi cations for units supplied
outside the U.S.A. may vary slightly at different AC voltages
and frequencies.
Power
Output Power: See power charts below.
®
• Exclusive BCA
power design provides super efficiency for
quiet, fan-free operation
• Switchable input sensitivity
• “Soft start” feature prevents the K-Series amplifi er from drawing large currents when it is fi rst
turned on so you don’t need to delay power-on
of your amps
• Uniquely molded, cast-aluminum front panel
provides exceptional air circulation for your KSeries amplifi er
• Three-year, No-Fault, Fully Transferable Warranty completely protects your investment and
guarantees its specifi cations
Voltage Gain:
K1: 31.55 dB gain at 1.4 volt sensitivity;
26 dB gain at 2.65 volt sensitivity.
K2: 32.88 dB gain at 1.4 volt sensitivity;
25 dB gain at 3.0 volt sensitivity.
Line Voltage Requirements: Universal power
supply can be confi gured to operate with
100,120, 200, 220, 230, 240, 250VAC at 50
or 60 Hz. Adapters are acquired through an
Authorized Service Center.
(Balanced Current Amplifi er)
Performance
Frequency Response: ±0.25 dB from 20 Hz to
20 kHz. The frequency response is band limited
with an 8 Hz double-integrated 3rd-order Butterworth high-pass fi lter and a 30 kHz 7th-order
Gaussian low-pass fi lter.
Signal to Noise (A-weighted): > 100 dB below
rated power.
Damping Factor: > 3,000 from 10 to 400 Hz.
*
K1
2 ohm Stereo (per channel)
4 ohm Stereo (per channel)
8 ohm Stereo (per channel)
4 ohm Bridge-Mono
8 ohm Bridge-Mono
*1 kHz Power: refers to maximum average power in watts
at 1 kHz with 0.1% or less TRUE THD.
1 kHz
Power
750W
550W
350W
1,500W
1,100W
*
K2
2 ohm Stereo (per channel)
4 ohm Stereo (per channel)
8 ohm Stereo (per channel)
4 ohm Bridge-Mono
8 ohm Bridge-Mono
*1 kHz Power: refers to maximum average power in watts
at 1 kHz with 0.1% or less TRUE THD.
1 kHz
Power
1,250W
800W
500W
2,500W
1,600W
Controls
Level: A calibrated rotary level control for each
channel located on the front panel.
Power: An on/off rocker switch located on the
front panel.
Input Sensitivity: A two-position switch for
each channel located on the back panel near
each channel’s input connectors.
Bridge Output: An on/off switch located on
the back panel between the input connectors
which, when turned on, bridges the two output
channels for twice the output voltage.
Page 2
K1
K2
“Y” Input: An on/off switch located on
the back panel between the input connectors
which, when turned on, parallels the two
input channels.
Indicators
TLC: A TLC (thermal level control) LED for each
channel which turns on with a dim glow shortly
before the amplifi er needs help dissipating heat.
Clip: An orange LED for each channel which
turns on when distortion of any type becomes
audible in the amplifi er output.
IOC: A yellow LED for each channel which
serves as a distortion indicator. The IOC indicators include a pulse-stretching feature that
helps make them more noticeable even with
rapid transient signals
Signal: A green LED for each channel which
fl ashes dimly when a very low-level signal (as
low as 10 mW) is present in the output. They
fl ash brightly when a louder signal (at least 1
watt) is present at the output.
Enable: A green LED that turns on when the
amplifi er has been turned on and has power.
When fi rst turned on, there will be a brief twosecond delay while the amplifi er performs a
quick turn-on diagnostic. Then the Enable indicator will turn on to its full brightness. If
no signal is present, the Enable indicator
will switch to a dim level.
Input/Output
Input Connectors: One balanced ¼-inch
(6.35-mm) phone jack and one 3-pin female
XLR connector for each channel.
Input Stage: Input is electronically balanced
and employs precision 1% resistors.
Input Impedance: Nominally 20 k ohms, balanced. Nominally 10 k ohms, unbalanced.
Output Connectors: Two sets of color-coded
binding posts for banana plugs, spade lugs
or bare wire (European models do not accept
banana plugs.)
DC Output Offset: ±10 millivolts.
Output Signal
Stereo: Unbalanced, two-channel.
Bridge-Mono: Balanced, single-channel. Chan-
nel 1 controls are active; Channel 2 should be
turned down.
Protection
K-Series amplifi ers are protected against
shorted, open or mismatched loads; overloaded
power supplies; excessive temperature, chain
destruction phenomena, input overload damage
and high-frequency blowups. They also protect
loudspeakers from input/output DC, DC offset
and turn-on/turn-off transients.
TLC protection circuitry protects the amplifi er
from excessive heat by subtly and dynamically
reducing the gain only when necessary to
reduce heat levels. Transformer overheating (an
extremely unlikely event) will result in a temporary shutdown; when it has cooled to a safe
temperature, the transformer will automatically
reset itself. Controlled slew rate voltage amplifi ers prevent RF burnouts, and input overload
protection is provided by the input current limit.
Out-of-band low-pass and high-pass fi lters protect the amplifi er and loads from subsonic frequencies below 8 Hz and ultrasonic frequencies
above 30 kHz.
Tur n O n: State-of-the-art “soft start” feature
prevents the amplifi er from drawing a large
inrush current when it is fi rst turned on and no
dangerous artifacts are produced by the amplifi er. (However it is recommended that all equipment ahead of the amplifi er be turned on fi rst
since they may produce turn-on transients.)
Construction
Cast-aluminum front panel with durable fi nish
and Lexan labels. Aluminum chassis with durable black fi nish.
Cooling: High-performance passive convection
cooling system allows the amplifi er to drive
2 ohm loads to high music sound levels (6 dB
into clip) in a 40° C (104° F) ambient environment .
Dimensions: Standard 19-inch (48.3-cm) rack
mount width (EIA RS-310-B), 3.5 inches (8.9
cm) high and 16 inches (40.6 cm) deep behind
front mounting surface.
Net Weight:
K1: 32 lb (14.6 kg).
K2: 38 lb (17.3 kg).
Shipping Weight:
K1: 38 lb (17.3 kg).
K2: 44 lb (20.0 kg).
Center of gravity approximately 6 inches (15.2
cm) behind front mounting surface.
Crown’s Three-Year, No-Fault, Fully Transferable Warranty
Crown offers a Three-Year, No-Fault, Fully Transferable Warranty for every new Crown amplifi er—an unsurpassed industry standard. With this unprecedented No-Fault protection, your new
Crown amplifi er is warranted to meet or exceed original specifi cations for the fi rst three years of
ownership. During this time, if your amplifi er fails, or does not perform to original specifi cations,
it will be repaired or replaced at our expense. About the only things not covered by this warranty
are those losses normally covered by insurance and those caused by intentional abuse. And the
coverage is transferable, should you sell your amplifi er.
See your authorized Crown dealer for full warranty disclosure and details. For customers outside
of the USA, please contact your authorized Crown distributor for warranty information or call
574-294-8200.
Crown International
1718 W. Mishawaka Rd.
Elkhart, IN 46517-9439
TEL: 574-294-8200
FAX: 574-294-8FAX
www.crownaudio.com
Specifi cations subject to change without prior notice. Latest
information available at www.crownaudio.com.
Crown, Crown Audio, K2 and BCA are registered trademarks
of Crown International. Other trademarks are the property of
their respective owners. Printed in U.S.A.
© 2005 Crown Audio
7/05 136713-1B
®
, Inc.
Loading...