Page 1
Embedded Electric Fireplace
Instruction Manual
MODEL: QR-23
AC 110-120V~ 60Hz 1500W
PLEASE READ ALL INSTRUCTIONS CAREFULLY
AND RETAIN THIS MANUAL FOR FUTURE
REFERENCE
Page 2
QUICK REFERENCE GUIDE
I. Remove the fireplace from the box.
II. Remove all the packaging and place it inside the box and
either store or dispose of safely.
III. Prior to installation, please ensure:
1. The rated voltage of your fireplace fits the output
voltage of your outlet;
2. The light bulbs in your fireplace is in good
condition. For checking this, please follow the
instructions for replacing the light bulbs on section
MAINTENANCE.
IV. The heater on your fireplace may emit a slight, harmless
odor when first used. This odor is a normal condition
caused by the initial heating of internal heater parts and
will not occur again.
V. If your heater does not emit heat, please ensure the
Heater Switch is on. For further information, please
consult section Operation of the Practical User's Guide.
Marks
NOTE
Procedures and techniques, that are considered important
enough to emphasize.
CAUTION
Procedures, which if not carefully followed, will result in
damage to the equipment.
WARNING
Procedures, which if not carefully followed, will expose the
user to the risk of serious injury, illness or death.
1
Page 3
IMPORTANT INSTRUCTIONS
WARNING
You should read and always follow the instructions
mentioned below to reduce the risk of fire, electric shock,
and injury.
1. Read all instructions before using this fireplace.
2. This fireplace is hot when in use. To avoid burns, do not
let bare skin touch hot surfaces, such as surfaces near the
fireplace outlet or light bulbs. Keep combustible materials,
such as clothes, pillows, furniture, bedding, papers and
curtains at least 3 feet from the front of the unit. Do not
cover or block fireplace outlet or any ventilation or exhaust
opening at any time. Do not use on soft or uneven
surfaces where openings may become blocked.
3. Extreme caution is necessary when any fireplace is used
by or near children or infants.
4. Fireplace should never be left unattended.
5. Do not install the fireplace directly on carpet or a similar
surface, which may restrict air circulation beneath the unit.
6. Always unplug fireplace when not in use.
7. To disconnect fireplace, turn controls off, then remove
plug from outlet.
8. Do not use outdoors.
9. This fireplace is not intended for use in wet locations, such
as bathrooms, laundry areas and similar indoor locations.
Never locate fireplace where it may fall into water
container from.
10. Do not operate the fireplace with a damaged cord or plug,
or if the fireplace has malfunctioned, or if the fireplace has
been dropped or damaged in any manner. Contact
Customer Service and seek assistance.
11. Keep furniture, curtains and other flammable material at
least 40 inches away from the fireplace.
2
Page 4
12. Do not run cord under carpeting. Do not cover cord with
throw rugs, runners, or the like. Arrange cord away from
traffic area and where it will not be tripped over.
13. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the fireplace.
14. To prevent a possible fire, do not block air intakes or
exhaust in any manner. Do not use on soft surfaces, like a
bed, where openings may become blocked.
15. All electrical fireplaces have hot and sparking parts inside.
Do not use it in areas where gasoline, paint, or flammable
liquids are used or stored or where the unit will be
exposed to flammable vapors.
16. Do not modify this fireplace. Use it only as described in
this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock or injury to
persons.
17. Avoid the use of an extension cord because the extension
cord may overheat and cause a risk of fire. However, if
you have to use an extension cord, the cord shall be
16AWG minimum size and rated not less than 125V/15A
or 2000 watts.
18. Do not burn wood or other materials in this fireplace.
19. If the supply cord is damaged, it must be replaced by a
special cord or assembly available from the manufacturer
or its service agent.
20. Do not strike fireplace glass.
21. Always use a certified electrician should new circuits or
outlets be required.
22. Always use properly grounded, fused and polarized outlets.
23. Always use ground fault protection where required by
electrical code.
24. The fireplace must not be located immediately below a
power-outlet
25. Always disconnect power before performing any cleaning,
maintenance or relocating the fireplace.
3
Page 5
26. When transporting or storing the fireplace and cord, keep
in a dry place, free from excessive vibration to avoid
damage to the fireplace.
27. WARNING: In order to avoid overheating, do not
cover the fireplace.
28. This fireplace is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the fireplace by a person responsible for
their safety.
29. Children should be supervised to ensure that they do not
play with the fireplace.
30. Indoor and household use
31. CAUTION: In order to avoid a hazard due to inadvertent
resetting of the thermal cutout, this fireplace must not be
connected to an external switching device, such as a timer,
or connected to a circuit that is regularly switched on and
off by the utility.
32. Do not use this apparatus near water.
33. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
34. Only use attachments/accessories specified by the
manufacturer.
35. This unit is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities or lack of experience or knowledge. They
should be given appropriate supervision and instructions
about the use of the unit by a person responsible for their
safety.
36. Close supervision is recommended when using this unit
near young children.
SAVE THESE INSTRUCTIONS
4
Page 6
Installation
This section provides step-by-step instructions for installation of
your fireplace.
WARNING
The outlet must be 15A/125V.
CAUTION
Do not remove the four rubber feet at the bottom of the
fireplace insert or install the fireplace insert directly on soft
surfaces, which may restrict air circulation. Otherwise, it
may cause a risk of fire or damage.
1. Select a suitable location, which is not susceptible to moisture,
safe, dust free, away from high traffic and away from things
may catch fire or block openings such as drapes, furniture, etc.
NOTE
This fireplace is built-in appliance and for household
use only.
It is a good idea to place your fireplace near an
existing outlet, for ease of electrical hook up.
2. Place the fireplace in the desired location to see how it will
look in the room.
3. Place the mantel in the desired location or build a wall
construction in the desired location.
4. The size of space for inserting should be 610mm (Wide) X
550mm (High) X230mm (Deep) ����
CAUTION
5
Page 7
Store your fireplace insert in a dry, safe and
dustless place when placing the mantel or building
the wall construction.
5. If there's no 15A/125V outlet near the desired location, install a
new one near or behind mantel.
WARNING
Do not attempt to wire you own new outlets or
circuits. To reduce the risk of fire, electric shock or
injury to persons, always use a licensed electrician.
6. Make sure the fireplace insert is switched off (refer to
operation instruction section).
7. Plug the fireplace into a 15A/125V outlet. Wiring the cord along
the corner of wall.
8. Push the fireplace insert into place so that the panel and the
finished mantel surround or wall surface are in the same plane.
Instruction for use
The fireplace can be operated either with the switches located on the
top right hand side of the fireplace or with the supplied remote control.
Manual Operation
• This is done by operating
the switches located at the
bottom right hand side of
the fire. The standby switch
must first be switched on.
The fireplace will beep to
indicate that it is powered
Page 8
up.
• Press the on/off button once to turn on the fireplace with fire
effect. A red indicator light will illuminate to indicate that the
fireplace is on.
• Press the low button once, to lower the heat; press twice to
switch off the heat completely.
• Press the high button once to increase the heat; press twice
to switch off the heat completely.
• Press the dimmer button to operate the dimmer mode.
Repeated pressing will automatically raise and lower the
brightness of the fire effect.
Remote Operation
• The standby switch must first be
switched on. The fireplace will beep
to indicate that it is powered up.
• It takes a little time for the receiver
to respond to the transmitter. Do not
press the buttons more than once
within two seconds, for the fireplace
to operate normally.
• Press the on/off button once to turn
on the fireplace with fire effect.
• Press the low button once, to lower
the heat; press twice to switch off the heat completely.
• Press the high button once, to increase the heat; press twice
to switch off the heat completely.
• Press the dimmer+ button to operate the dimmer mode to
raise the brightness of the fire effect.
• Press the dimmer- button to operate the dimmer mode to
lower the brightness of the fire effect..
7
Page 9
• Press the Lamp button is on or off the brightness of the fire
effect.
Safety Cut-Off
• This fireplace is equipped with safety cut-off feature which will
operate if the fireplace overheats (e.g. Due to blocked air
vents). For safety reasons, the fireplace will NOT
automatically restart.
• To restart the fireplace, disconnect it from the power supply
for at least 15 minutes. Reconnect to the power supply and
switch on the fireplace.
Troubleshooting
Symptom
Possible Solution
No operation / no fan
Check for safety cut-off
operation
No fire effect light Check the bulb for replacement
Remote Not Working
Check if batteries have been
installed as per indicated
polarity
Remote Not Working
Check if batteries need to be
replaced
Remote Not Working
Point the Remote Control
directly at the fireplace
MAINTENANCE
WARNING
Disconnect power before attempting any maintenance or
cleaning to reduce the risk of fire, electric shock to persons
or damage.
Light Bulb Replacement
Light bulbs need to be replaced when you notice a dark section of
Page 10
the flame or when the clarity and detail of the log exterior
disappears. There are two bulbs under the log set.
WARNING
Allow at least 5 minutes for light bulbs to cool off before
touching bulbs to avoid burning of skin.
I. Bulb Requirements
Quantity of 2 clear chandelier or candelabra bulbs with an
E-12 socket base, rating voltage 125 volts, rating power
40 watts.
CAUTION
Do not exceed 40 watts per bulb
II. Operation
1. Open the light bulb area:
The light bulb area is at the back of electric fireplace,
see "E" . there are 4 screws on it. loosen the screw by
some tool, then you can open it. (Figure below)
2. Examine the bulbs to determine which bulbs require
replacement.
3. Remove old bulb and replace a new one. Hold the
socket while unscrewing or screwing bulbs. (Figure
below)
4. Replace the cover of light bulbs.
5. Done.
9
Page 11
Cleaning and Maintenance
• Warning: Always disconnect from the power supply before
cleaning the fireplace.
• For general cleaning use a soft, clean duster. Never use
harsh abrasives or cleaners. The glass screen should be
cleaned carefully with a soft cloth. DO NOT use
proprietary glass cleaners.
Technical Specification
• Supply: 110-120V~60Hz
• Rated power: 1500W
. Lighting: 2x40W E12 Bulbs
Correct Disposal of this product
X
This marking indicates that this product should
not be disposed with other household wastes
throughout the EU. To prevent possible harm to
the environment or human health from
uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of
material resources. To return your used device,
please use the return and collection systems or
contact the retailer where the product was
purchased. They can take this product for
environmental safe recycling.
10
Loading...