Crouzet 88 970 574 Installation Instructions
Installation and Startup Guide
Environmental
Considerations
(1) Storage temperature -20°C/+60°C.
(2) Do not let water penetrate into packaging boxes during their storage and
transportation.
(3) Do not store the product in places of high temperature or under direct
sunlight
(4) Please also avoid the places of high humidity. Be sure not to expose the
product to condensation, rain or frozen condition
NEMA Rating
CTP110-E Series HMI is NEMA 4 rated.
Electrical
Environment
CTP110-E Series HMI has been tested to conform to European CE requirements.
This means that the circuitry is designed to resist the effects of electrical noise.
This does not guarantee noise immunity in severe cases. Proper wire routing and
grounding will insure proper operation.
Environmental
Considerations
(1) Make sure that the displays are installed correctly and that the operating
limits are followed. Avoid installing units in environments where severe
mechanical vibration or shocks are present.
(2) Do not operate the unit in areas subject to explosion hazards due to
flammable gases, vapors or du sts.
(3) Do not install the unit where acid gas, such as SO2 exists.
(4) This device should be mounted in the vertical position and for use on the flat
surface enclosure.
Type
A(mm)
B(mm)
CTP110-E
250
192
CTP110-E series 88 970 574
Installation Instruction
1
2
NOTE:
Place the operator panel on a stable
surface during installation. Dropping it or
letting it fall may cause damage.
(1) Installation Instruction, 2-sided A4 *1
(2) Human Machine Interface *1
(3) Power Connector *1
(4) Brackets & Screws *1 pack
(5) Fuse 1.25A/250V 5*20mm *1
3
5
4
(4)
A)
(B)
Cutout
This document covers the installation of CTP 110-E Series HMI, for the detailed specifications
and operation, please refer to Brochure and Crouzet Touch Soft User Manual.
Handling and Storage:
Install Environment:
The packing box can be transformed into an HMI stand. Please follow the steps to make the stand.
1. Remove the center of the box cover along the perforated line.
2. Pull the two inner flaps.
3. Press down along the perforated line inside the box.
4. Complete the stand as shown.
Installation Instructions
Secure the operator panel in position, using all the fastening holes and the provided brackets
and screws. Screw Torque: 0.29 ~ 0.44 Nm (For reaching waterproof effect and preventing the panel
from being deformed.)
(
Unpacking the Unit
Unpack and check the delivery. If damage is found,
notify the supplier.
(1)
(2)
(5)
(3)
Power Connections
NOTE:
1. Connect positive DC line to the ‘+’ terminal and
the DC ground to the ‘-’ terminal.
2. Please do not connect HMI with PLC and PC
simultaneously to prevent potential difference
from destroying USB ports of HMI and PC.
System Settings
When HMI is powered up and displays image,
press the system setting button in the lower-right corner of
the screen.
(Default System Password: 111111)
Go to the Network tab, you may choose to auto get DHCP IP,
or designate your own IP.
CTP110-E has two10/100/1000 Base-T Ethernet ports.
The default IP addresses are:
LAN 1: DHCP
LAN 2: 192.168.100.1
Crouzet Touch Soft Settings
PIN#
COM1 [RS232]
COM3 [RS232]
1
2
RxD
3
TxD
4
5
GND
6
7
RTS
TxD 8 CTS
RxD
9
PIN#
COM2 [RS485]
COM3
[RS485]
2W
4W
1
Data-
Rx-
2
Data+
Rx+
3
Tx- 4 Tx+ 5 6
Data- 7 8 9 Data+
NOTE:
1. Only Tx & Rx (no RTS/CTS) may be used for COM1 RS-232 when COM3 RS-232 is also used.
6
7
8
Limited Warranty
An Internal fuse will prevent damage for overcurrent condition however it isn’t guaranteed. DC
voltage sources should provide proper isolation from main AC power and similar hazards.
A Hard-wired EMERGENCY STOP should be fitted in any system using HMI to comply with ICS
Safety Recommendations.
Do not power the unit and inductive DC loads, or input circuitry to the controller, with the same
power supply. Note: The 24 VDC output from some controllers may not have enough current to
power the unit.
a. Power wire length should be minimized (Max: 500m shielded, 300m unshielded).
Hardware
Considerations
The system designer should be aware that devices in Controller systems could fail and thereby
create an unsafe condition. Furthermore, electrical interference in an operator interface can lead to
equipment start-up, which could result in property damage and/or physical injury to the operator.
If you use any programmable control systems that require an operator, be aware that this potential
safety hazard exists and take appropriate precautions. Although the specific design steps depend on
your particular application, the following precautions generally apply to installation of solid-state
programmable control devices, and conform to the guidelines for installation of Controllers
recommended in NEMA ICS 3-304 Control Standards.
Considerations
To conform with ICS Safety Recommendations, checks should be placed in the controller to ensure
that all writable registers that control critical parts of plant or machinery have limit checks built into
the program, with an out-of-limit safe shut down procedure to ensure safety of personnel.
This product is an electronic device (EEE) and as such, must be sent to approved authorized
treatment facility (*) after service life for proper disposal.
This product includes a lithium battery.
Do not open it by force; do not throw it in fire.
In compliance with Directive 2006/66/UE requirements, we inform you that batteries must not be
discarded in household waste, and must also be sent to approved authorized treatment facility (*)
after service life for proper disposal.
(*) visit http://www.crouzet-automation.fr/assistance/valorisation-des-dechets/
GMECT11E0_CTP110-E_Installation_161006
Considerations
DANGER
The unit can be powered by DC power only, voltage range: 24±20% Volts DC, compatible with
most controller DC systems. The power conditioning circuitry inside the unit is accomplished by a
switching power supply. The peak starting current can be as high as 2A.
If the display does not come on within 5 seconds of power up, remove power. An internal fuse will
prevent damage if the polarity of the DC power is incorrect. Check wiring for proper connections
and try to power up again.
NOTE:
installing the unit. Contact your local authorities to determine which codes apply.
Launch Crouzet Touch Soft software, select your
project file, press F7 shortcut key to open the
download dialog box: Select Ethernet > IP tab > Enter
your HMI IP >
Click Download to download this project file to
HMI.
(Please refer to Crouzet Touch Soft User Manual
for software operation details )
Communication Connections
Con.B Con.A
COM1/3 [RS232] 9 Pin, Male, D-sub COM2/3 [RS485] 9 Pin, Female, D-sub
High
Voltage
Emergency
Stop
Supply
Voltage
Condition
Wire
Routing
b. Please use twisted pair cables for power wire and signal wire and conform to the impedance
matching.
c. If wiring is to be exposed to lightning or surges, use appropriate surge suppression devices.
d. Keep AC, high energy, and rapidly switching DC power wiring separated from signal wires.
e. Add a resistor and capacitor in the parallel connection between the ungrounded DC power
supply and the frame ground. This provides a path for static and high frequency dissipation.
Typical values to use are 1M Ohm and 4700pF.
Calibration Mode
To enter touch screen calibration mode, press and hold anywhere on the screen for more than 2
seconds when HMI starts.
Make sure that all local and national electrical standards are met when
Power
Fusing
Requirements
Programming
Disposal
This product is limited warranted against defects in design and manufacture.
The proven defective product will either be repaired or replaced, at Crouzet’s discretion.
This warranty shall not cover any product which is
(a) Out of warranty period which is 12 months from the manufacturing month of the HMI products.
(b) Damage caused by Force Majeure, accident, negligence, improper installation or misuse.
(c) Product has been repaired or taken apart by unauthorized technicians.
(d) Products whose identification markings have been removed or damaged.
Loading...