Crouzet 84873222, 84873220, 84873221 Data Sheet

Phase control
M3US
H3US
H3USN
Part numbers
Product adaptations
Accessories
General characteristics
3-phase voltage control relay - 17.5 mm / 35 mm
H3US and M3US relays control, on 3-phase networks:
- overvoltage between phases,
- undervoltage between phases
The H3USN relay controls, on 3-phase networks:
- overvoltage between phases and neutral,
- loss of neutral
Multi-voltage Products
Controls its own supply voltage
True RMS measurement
LED status indication
M3US H3US H3USN
Function Under/overvoltage
Nominal voltage (V) Output 1 single pole changeover
Part numbers
between phases
3 x 208
3 x 480 V
relay
84873222 84873220 84873221
Under/overvoltage between phases
a
3 x 220 3 x 480 V 2 single changeover
relays / one per threshold
Over and undervoltage between phases and neutral / loss of neutral
a
3 x 120 3 x 277 V 2 single changeover
relays / one per threshold
a
Customisable colours and labels
Single voltage in the generic range
Fixed or adjustable time delay
Adjustable fixed hysteresis
Adaptations dedicated to M3US:
Fixed threshold in the generic range
Adaptations dedicated to H3US:
Fixed threshold in the generic range
Adaptations dedicated to H3USN:
Fixed overvoltage threshold in the generic range
Fixed undervoltage threshold in the generic range
Description Code
Removable sealable cover for 17.5 mm casing 84800000 Removable sealable cover for 35 mm casing 84800001
M3US H3US H3USN
Supply
Supply voltage Un Voltage supply tolerance -12% / +10% -12% / +10% -20% / +20%
Operating range Power consumption at Un
Inputs and measuring cicuit
Selection of phase-phase nominal voltage Un 208-220-380-400-415-
Selection of phase-neutral voltage - - 120-127-220-230-240-260-277
Output
Electrical life (number of operations)
General characteristics
Casing 17.5 mm 35 mm 35 mm Weight 80 g 130 g 130 g
Comments
3 x 208
3 x 480 V
183
528 V
1.8 VA in
440-480 V
1 x 10
* 3-phase mains with earth * 3-phase mains with earth * 3-phase mains with earth
a
a
5
a
a
* 3 x 220 3 x 480 V a * 3 x120 3 x 277 V a *
194 528 V
2.9 VA in
220-380-400-415-440­480 V
1 x 10
a
a
a
4
96 332 V
3.9 VA in
-
1 x 10
a
a
4
26
www.crouzet.com
General characteristics
Supply
a
supply voltage frequency
Galvanic isolation of power supply/measurement No
Inputs and measuring cicuit
Frequency of measured signal 50 Max. measuring cycle time 150 ms/True RMS measurement Voltage threshold adjustment
Fixed hysteresis 2% of Un (M3US, H3US) Display precision ± 3% of the displayed value Repetition accuracy with constant parameters ± 0.5% Measuring error with voltage drift < 1% across the whole range Measuring error with temperature drift 0.05% / °C
Timing
Delay on threshold crossing 0.3 Repetition accuracy with constant parameters ± 3% Reset time 1500 ms Delay on pick-up 500 ms Alarm on delay time max. 200 ms
Output
Type of contacts No cadmium Maximum breaking voltage
Max. breaking current Min. breaking current Breaking capacity (resistive) Maximum rate 360 operations/hour at full load
Operating categories acc. to IEC 60947-5-1 AC 12, AC 13, AC 14, AC 15, DC 12, DC 13, DC 14 Mechanical life (operations)
Insulation
Nominal insulation voltage IEC 60664-1 400 V Insulation coordination (IEC 60664-1 / 60255-5) Overvoltage category III: degree of pollution 3 Rated impulse withstand voltage IEC 60664-1/60255-5 4 KV (1.2 / 50 µs) Dielectric strength IEC 60664-1/60255-5 2 kV AC 50 Hz 1 min Insulation resistance IEC 60664-1 / 60255-5
General characteristics
Display power supply Green LED Display relay Yellow LED (1 for M3US, 2 for H3US and H3USN) Mounting On 35 mm symmetrical DIN rail, IEC/EN 60715 Mounting position All positions Material: enclosure plastic type VO to UL94 standard Incandescent wire test according to IEC 60695-2-11 & NF EN 60695-2-11 Protection (IEC 60529) Terminal block: IP 20
Connecting capacity IEC 60947-1
Max. tightening torques IEC 60947-1 0.6 Operating temperature IEC 60068-2 -20 Storage temperature IEC 60068-2 -40 Humidity IEC 60068-2-30 2 x 24 hr cycle 95% RH max. without condensation 55°C Vibrations according to IEC/EN60068-2-6 10 Shocks IEC 60068-2-6 5 g
Standards
Marking CE (LVD) 73/23/EEC - EMC 89/336/EEC Product standard NF EN 60255-6 / CEI 60255-6 / UL 508 / CSA C22.2 N°14 Electromagnetic compatibility Immunity EN 61000-6-2/IEC 61000-6-2
Certifications UL, CSA, GL
Conformity with environmental directives RoHS, WEEE
50 / 60 Hz ±10%
60 Hz ± 10%
b
Undervoltage -2 to -20% of selected Un for M3US: (-2 to -12% across the 3 x 208 V range) (-2 to -17% across the 3 x 220 V range) for H3US: (-2 to -12% across the 3 x 220 V range)
b
Overvoltage 220% of selected Un For M3US and H3US:
(+2
+10% across the 3 x 480 V
30 s (0, +10%)
z
250 V
z
5 A 10 mA / 5 V 1250 VA
30 x 10
> 500 M / 500 V
Casing: IP30 Rigid: 1 x 4
1 x 11 AWG - 2 x 14 AWG Flexible with ferrules: 1 x 2.5 1 x 14 AWG - 2 x 16 AWG
150 Hz, A = 0.035 mm
Emission EN 61000-6-4/EN 61000-6-3 IEC 61000-6-4/IEC 61000-6-3 Emission EN 55022 class B
c
a
6
c
2
- 2 x 2.52 mm2
1 Nm / 5.3 8.8 Lbf.Ft+50°C+70°C
a
range)
2
- 2 x 1.52 mm
pending
2
27
Overview
Phase control
Principles
3-phase voltage controllers which monitor:
- Undervoltage, adjustable from -20 to -2% of Un
- Overvoltage, adjustable from 2 to 20% of Un
- Presence of the neutral (H3USN only) Measurements are taken between Phases for the H3US - M3US and between Phases and Neutral for the H3USN Faults are signalled via LEDs, distinguishing the origin of the fault (one LED for the upper threshold, one LED for the lower threshold).
Voltage selector switch: Set the selector switch to the 3-phase network voltage Un. The position of this selector switch is only taken into account when the unit is powered up. If the switch position changes while the unit is operating, all the LEDs flash but the product continues to work normally with the voltage selected on energisation prior to the change of position. The LEDs return to their normal state if the switch is reset to its initial position defined before the last energisation.
M3US - Under/Overvoltage Operating principle
1
L1 L2
2
L3
3 4
5
6 6
Overvoltage
B
Hysteresis
C
Undervoltage
D
Phases L1, L2, L3
E
Relay
F
Over and undervoltage threshold delay
G
H3US - H3USN - Under/Overvoltage Operating principle
1
L1 L2
2
L3
3
4 5
6
7 8
Overvoltage
B
Hysteresis
C
Undervoltage
D
Phases L1, L2, L3
E
Relay R1
F
Relay R2
G
Overvoltage threshold delay
H
Undervoltage threshold delay
I
M3US
The relay monitors its own supply voltage. It controls:
- Undervoltage, adjustable from -20 to -2% of Un (-12 to -2% over the 3 x 208 V 17% to -2% for the 3 x 220 V
- Overvoltage, adjustable from +2 maximum voltage 528 V
An adjustable time delay from 0.3 to 30s can be used to disable the output relay during a transient fault. In the event of a voltage fault, the relay opens at the end of the time delay set by the user. In the event of phase failure, the relay opens instantaneously, without waiting for the end of the time delay. When the unit is powered up with a measured fault, the relay stays open.
H3US
The relay monitors its own supply voltage. It controls:
- Undervoltage, adjustable from - 2 to - 20% of Un (-2 to -12% over the 3 x 220 V the minimum voltage 194 V
- Overvoltage, adjustable from + 2 to +20% (+2 to +10% over the 3 x 480 V maximum voltage 528 V
Each threshold has its own time delay with independent setting between 0.3 and 30 s. In the event of a voltage fault, the corresponding relay (one undervoltage output/one overvoltage output) opens at the end of the time delay set by the user. In the event of phase failure, both relays open instantaneously, without waiting for the end of the time delay. The two relay LEDs go out.
H3USN
The relay monitors its own supply voltage. It controls:
- Presence of the neutral,
- Undervoltage, adjustable from -2 to -20% of Un,
- Overvoltage, adjustable from +2 to +20%. Each threshold has its own time delay with independent setting between 0.3 and 30 s. In the event of a voltage fault, the corresponding relay (one undervoltage output/one overvoltage output) opens at the end of the time delay set by the user. If neutral is lost, both relays open instantaneously and the corresponding LED is extinguished, without waiting for the end of the time delay. The two relay LEDs are extinguished.
a
range due to the minimum voltage 183 V a)
a
a
+20% (+2 +10% over the 3 x 480 V
).
a
)
).
a
range and -
a
range due to the
a
range due to
a
range due to the
28
Dimensions (mm)
www.crouzet.com
M3US
60
3,5
45
67,5
Connections
M3US
L1
L2
L3
1
F1
L1 L2RL3
L2
L3
L1
12
1112 14
100 mA fast-blow fuse or cut-out
B
H3US
H3US - H3USN
44
23,2
5,5
17,5
3,5
90
2,6
67,5
45
60
44
23,2
5,5
35
90
2,6
H3US - H3USN
– KM1
11
14
U1
V1
W1
M1
3
L1
L2
L3
1
F1
L1 L2
L2
L3
L1
12
1112 14
22 21 24
100 mA fast-blow fuse or cut-out
B
11
R1 R2
22
14
– KM1
L3
21
24
U1
W1
V1
M1
3
L1
L2
L3
N
1
F1
L1 L2
L2
L3
(N)
L1
12
1112 14
22 21 24
100 mA fast-blow fuse or cut-out
B
L3
11
R1 R2
22
14
W1
U1
V1
M1
3
– KM1
(N)
21
24
29
Loading...