Page 1
INSTALLATION INSTRUCTIONS
For any further information please contact
Crosswater on: 0845 873 8840
Or visit our web-site at www.crosswater.co.uk
The manufacturer reserves the right to make technical
modifications without prior notice.
P5-Z0A158-E A/1
KL0007WC
4 Way Diverter wall mounted
Page 2
1
2
INTRODUCTION
DIMENSIONS
NOTE: ALL DIMENSIONS IN MILLIMETRES
KL0007WC
PARTS IDENTIFICATION
NOTE: ALL DIMENSIONS IN MILLIMETRES
38
53
8
2-G1/2
96
32
50
60-66
114
34
60
3-G3/4
HOT
INLET
COLD
INLET
MAIN OUTLET
(SHOWER-FIXED HEAD)
This diverter valve is suitable for use with all water systems with a operating
pressure 1 Bar up to 5.0 bar, (beyond which we recommend pressure reducing
valves to be fitted).
The valve has three outlets that allow for additional fittings to be supplied.
BATH BODY JETS
OR HAND SHOWER
BATH
BODY JETS
OR HAND SHOWER
Page 3
INSTALLATION
3
4
HEXAGONAL KEY
HANDLE
VALV E
INSTALLATION
First shut off your water heating system then, with your mains stop cock closed,
open the lowest hot and cold taps in the house and allow to run until the cold
storage tank and pipes are empty (the hot water storage cylinder always
remains full).
Where combination boilers are fitted it is only necessary to turn off the boiler
and shut off the incoming mains.
Fitting isolating valves to the inlet feeds is recommended for ease of
maintenance.
INSTALLATION
Remember to turn off the mains water supply before connecting to
any existing pipe work.
Warning! Please check for any hidden pipes and cables before
drilling holes in the wall
!
Once you have satisfied yourself that there are no leaks, switch on the water
heating.
!
ATTENTION
Having first checked all new connections, turn on the mains stop cock, close
all taps except the new mixer and as the system starts to refill check for leaks.
KL0007WC
COVER PLATE
BLANKING CAP(OPTIONAL)
3/8 FEMALE TO 1/2MALE ADAPTORS
The valve is secured in place by means of rigid (clipped) pipe work. Make sure
the valve is set back from the front face of the wall by the appropriate depth
to allow for plasterboard, filling and tiling etc.
Inlets and outlets are & ports. Make all pipe work connections using a
proprietary thread sealer. Do not use tapered threaded adaptors.
Blank off and seal the open outlet if it is not required.
Apply a narrow bead of clear silicone sealant around the back edge of the
cover plate and carefully press into position.
Fit the control knobs by lining up the flat surface of the valve cover with the
grub screw on the handle, tighten the screw with the supplied hexagonal key.
1/2"
3/4"
Page 4
KL0007WC
6
5
The chrome and gold plate we use on our taps is very durable, nevertheless care should
be taken when cleaning them. They should be cleaned only with warm soapy water
followed by rinsing with clean water and drying with a soft cloth. All finishes are vulnerable
to acid attack and some strong substances such as household cleaners, disinfectants,
denture cleaners, hair dyes, wine making and photographic chemicals can cause the
surface to go black or peel.
CLEANING
CLEANING THE CARTRIDGE
The concealed cartridge should give trouble free service, but in the event of any
problems, servicing is straight forward.
MAINTENANCE
To remove the cartridge.
First shut off the water supply then loosen the grub screw and remove the handle.
Take off the cover plate & threaded collar. Take off and keep safe the washer and
spindle before unscrewing the retaining nut.
Taking note of the orientation of the cartridge remove it.
Wash the cartridge with clean running water, dry and lightly grease the seal.
HEXAGONAL KEY
HANDLE
CARTRIDGE
WASHER
COVER PLATE
THREADED
COLLAR
SPINDLE
RETAINING NUT
VALV E
Loading...