crosscontrol CCpilot VS Technical Manual

Product revision: A

2017-11-23

CCpilot VS 12”

Technical Manual

www.crosscontrol.com

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

2

Contents

Revision history ..................................................................................................................................3

1. Introduction ..................................................................................................................................4

1.1. Document conventions ........................................................................................................... 4

1.2. Identification............................................................................................................................... 4

1.3. Environmental resistance ......................................................................................................... 4

2. Device overview ..........................................................................................................................5

2.1. Front side view ............................................................................................................................ 5

2.2. Rear side view ............................................................................................................................ 6

2.3. Left side view .............................................................................................................................. 6

3. Mounting and handling ...............................................................................................................7

3.1. Mounting ..................................................................................................................................... 7

3.2. Connecting to power supply .................................................................................................. 7

3.3. Cable installation ....................................................................................................................... 9

3.4. Special considerations.............................................................................................................. 9

3.5. Handling and maintenance ................................................................................................. 10

3.6. Transportation ........................................................................................................................... 11

3.7. Decommissioning .................................................................................................................... 11

4. Basic operation ..........................................................................................................................11

4.1. Turning ON/OFF ........................................................................................................................ 11

4.2. Light sensor ................................................................................................................................ 12

4.3. Using the touch screen ........................................................................................................... 12

4.4. Status notification .................................................................................................................... 12

4.5. Error codes ................................................................................................................................ 13

5. Interface overview .....................................................................................................................14

5.1. Front panel ................................................................................................................................ 14

5.2. Buzzer ......................................................................................................................................... 15

5.3. Analog video input ................................................................................................................. 15

5.4. CAN ............................................................................................................................................ 15

5.5. Ethernet ..................................................................................................................................... 15

5.6. USB .............................................................................................................................................. 16

5.7. Analog input ............................................................................................................................. 16

5.8. Configurable input .................................................................................................................. 16

5.9. High-side outputs ..................................................................................................................... 17

5.10. RS-232 ....................................................................................................................................... 18

5.11. RS-485 ....................................................................................................................................... 18

5.12. Key switch signal .................................................................................................................... 18

6. Connectors .................................................................................................................................18

6.1. Deutsch DT connectors, general .......................................................................................... 19

6.2. Deutsch DT connector A pinout ........................................................................................... 20

6.3. Deutsch DT connector B pinout ............................................................................................ 20

6.4. Deutsch DT connector C pinout ........................................................................................... 20

6.5. M12 connectors, general ....................................................................................................... 21

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

3

6.6. USB M12 connector pinout .................................................................................................... 21

6.7. Ethernet M12 pinout ................................................................................................................ 21

6.8. USB Type A connectors, general .......................................................................................... 22

6.9. USB Type A pinout .................................................................................................................... 22

7. Specifications .............................................................................................................................22

7.1. Technical data ......................................................................................................................... 22

7.2. Environmental specifications ................................................................................................ 26

7.3. EMC specification ................................................................................................................... 26

7.4. Weight and dimensions .......................................................................................................... 27

Technical support ............................................................................................................................29

Trademarks and terms of use ........................................................................................................29

Index .................................................................................................................................................30

Revision history

Rev

Date

Author

Comments

A

2017-11-23

Released

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

4

1. Introduction

CCpilot VS is a display computer with a 12” widescreen high-resolution TFT and PCAP touch
screen. The strong LED backlight in combination with the optically bonded PCAP, results in
excellent sunlight readability properties.

The powerful Arm® based main CPU and Linux® operating system constitute an open platform
that facilitates the implementation of premium user-machine interaction, reliable controls and
integrated fleet management solutions. In addition, there is one co-processor responsible for
hardware control and supervision.

This technical manual provides important information regarding the device’s hardware and its
basic usage. For software and operating system specifics, please see additional documentation.

1.1. Document conventions

This document uses the following conventions:

Description

Appearance

Important information

(exclamation symbol)

Text formats used in this document are described in the table below:

Format

Use

Italics

Names, designations, and references

Bolded

Important information

1.2. Identification

Each device has an identification label with serial number, article number and revision which
identify your unique device. Take note of these numbers. During service and other contact with the
supplier it is important to be able to provide this information.

Figure 1: Identification label

1.3. Environmental resistance

The CCpilot VS 12” device has been designed to manage tough environmental demands. Much
effort has been put into designing and selecting system components to provide a reliable and robust
device.

Thorough testing has been performed in order to ensure compliance to a broad range of applicable
regulatory requirements and to meet the user expectations of a ruggedized device for machinery
control.

A complete list of standards to which the device has been tested for compliance can be found in
chapters 7.2 and 7.3.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

5

2. Device overview

This chapter contains illustrations of the CCpilot VS 12” showing the location of external
connectors, indicators etc. Connectors are described in more detail in chapter 6. Additional
mechanical information can be found in chapter 7.4.

2.1. Front side view

At the front side of the device there is a 12” widescreen display with a projected capacitive touch­sensor (PCAP).

There is a light sensor in the front panel which enables automatic dimming of display.

Figure 2: CCpilot VS front side view

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

6

2.2. Rear side view

At the rear side of the device there are interface connectors, i.e. 3x Deutsch DT connectors, 2x M12
USB connectors and a M12 Ethernet connector.

There are also four M5 threaded inserts for mounting the device to a VESA75 mount.

Finally, there is a combined sound exit hole and ventilation membrane.

Figure 3: CCpilot VS rear side view

2.3. Left side view

On the left side of the device there is an on/off button with a built-in RGB status LED as well as two
USB type A connectors, placed under dust-protecting lids.

Figure 4: CCpilot VS left side view

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

7

3. Mounting and handling

This chapter contains recommendations for installation, handling and maintenance of the device.

3.1. Mounting

CCpilot VS 12” supports a standardized VESA75 mounting interface.

It is recommended to use 4 pc. M5 x 0.8 Allen screws, with a length of 12 mm. The recommended
fastening torque is 1.5 - 2.0 Nm. Using fluid locker or locking washers (split ring, toothed lock, etc.)
is required for proper mounting. Ensure that the M5 mounting screws are clean and dry before
mounting.

Note that the depth of the threaded holes is 8 mm. Be careful not to use too long screws which may
damage the device when tightened.

3.2. Connecting to power supply

This chapter describes how the CCpilot VS is preferably connected to the power supply of the
vehicle. The principle is the same also for other types of installations.

Carefully read through the following sub-chapters before installing the device. Connector pinouts
are found in chapter 6.

3.2.1. Wire gauge

Wire gauge for the power supply should be dimensioned with respect to the start current at
cranking.

 Current consumption of the CCpilot VS 12” device is found in chapter 7.1.
 Power consumption of external loads driven by the CCpilot VS 12” device should also be

taken into account.

 The wire gauge for the power supply is recommended to be at least 1.5 mm

2

/AWG 15 for

“normal” loads and at least 2.5 mm2 /AWG 14 if using high external loads.

 The DT connectors accept wire gauges between 0.75 and 3.3 mm

2

/AWG 12 to 18.

3.2.2. External fuse

To prevent cable fire in case of short circuit, an external fuse must always be used when powering
the device from a high current capable power source, for example a vehicle battery.

 The fuse shall be located as close to the battery/power source as practically possible.
 Fuse rating shall be dimensioned with respect to wire gauge, maximum current

consumption and the inrush current of the device. Refer to chapter 7.1 for fuse rating
details.

 As a guideline, a slow acting fuse with 15 A current rating should be used.
 Remember to also apply fusing for the on/off control wiring, see chapter 3.2.4.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

8

3.2.3. External key switch signal

The device’s key switch signal should be connected to the positive supply line via the vehicle’s

ignition key switch.

 The wire gauge for the key switch signal shall be dimensioned to handle the total switch

current and the fuse type and rating shall be selected to prevent cable fire in case of cabling
short circuit.

 As a guideline, a slow acting fuse in the range of 100-500 mA for the key switch signal

should be sufficient for most practically usable wire gauge.

3.2.4. Application example

Below is an application example schematic of the CCpilot VS 12” power supply connection.

If the system has a main switch for completely disconnecting the battery (S1 in schematic below),
the device’s power supply and key switch signal shall be connected after the main switch.

It is not recommended to disconnect the battery without shutting down the device first - since
doing so will immediately switch off all internal voltages, regardless of ongoing operations. Any
information which was not saved to flash memory will be lost when disconnecting the battery.
However, no physical damage will be caused to the device by disconnecting the battery.

Figure 5: Schematic example for power supply installation of a CCpilot VS 12” device in a
vehicle. The ignition switch (S2) can be shared by several devices (Device X, Y, …)

By connecting the power supply according to the example above, the CCpilot VS 12” device will
automatically start up when the key switch (S2) is closed and shut down when the switch is opened.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

9

Note that the on/off behavior of the CCpilot VS 12” described here is the default configuration. Its
response to the on/off signal may be altered using the CCAux API, see chapter 4.1 for more details.

3.3. Cable installation

Cables shall be installed in such a way that they don’t run any risk of being damaged, pinched or

worn.

 Avoid excessive bending and twisting of cables.
 Use strain-relief on cables near the device to minimize stress on cables and connectors.
 Properly snap the connectors to give reliable contact and sealing and to avoid unnecessary

strain.

 Shielded cables are recommended and in some cases necessary to ensure reliable

communication and appliance with agricultural EMC standards.

3.3.1. Recommendations for cable shields and coaxial cables

To achieve electromagnetic compliance and stable operation of the system, shielded cables are
required for Ethernet and USB interfaces. In addition, it is recommended to use 75 Ω coaxial cables
for connecting analog video sources to the device.

When using shielded cables for Ethernet, the shield is preferably connected/grounded at the other
end of the cable (and remain unconnected close to the CCpilot VS 12” device).

When using shielded cables for the M12 USB ports, the shield is preferably spliced and joined with
the USB connector’s shield. Avoid creating ground-loops in the USB cable by insulating any
attached USB-devices from ground structures connected with the CCpilot VS 12” device.

Below are recommendations for inserting cable shields and coaxial cables into Deutsch DT plugs to
achieve robust connections and retaining IP classification of the device.

 Splice the cable shield (or coaxial inner and outer conductors) outside of the DT plug and

use regular, round cables for insertion into the plug.

 Minimize distance between cable joints and the DT plugs for best shielding effect.

3.4. Special considerations

To ensure proper and reliable operation and to retain IP-classification of the device, below
recommendations must be followed:

 The device should be placed in a way that prevents direct exposure to water or close

proximity to hot-air vents.

 To enable sufficient cooling, the device must be installed in a way that allows ambient air to

circulate around it. A clearance of at least 50 mm around the device is recommended.

 To maintain IP classification, all three Deutsch DT connectors must be attached to the

device. Blind plugs must be used for unconnected pins. Please note that the protective caps
mounted on the DT connectors are for transportation protection only. The rubber sealing
of the USB-ports on the left side of the device must also be properly attached when not
using the USB-ports.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

10

 The device has a ventilation membrane, refer to Figure 3 for the location. For proper

ventilation of the device, dirt and water must be prevented from accumulating and covering
the membrane. Be cautious not to insert objects which may puncture the membrane. Doing
so will violate the IP-classification and void the warranty of the device.

 Install the device and any cables attached such that they are not subject to excess vibrations

or other potentially harmful stress.

 Loose fasteners are a common cause for excessive vibration. Fasteners may come loose due

to improper mounting techniques such as omitting thread lockers (fluid locker or locking
washers) or by over/under-tightening. Proper tightening requires dry, clean fasteners and a
torque wrench.

 If the device is exposed to chemicals, water, dirt or other pollutants, it’s recommended to

have it cleaned off as soon as possible. See chapter 3.5.1 for cleaning instructions.

3.5. Handling and maintenance

Handle the device with care and pay attention to the following handling instructions:

 Disconnect all cables to the device during welding or when performing other service to the

machine imposing a risk of damaging electronic devices.

 Service and repair to the device shall only be made by authorized personnel. If the device is

opened by unauthorized personnel, its warranty will be void.

 Scratches or other damages may occur to the display surface if it is exposed to sharp

objects, abrasives or heavy impacts. This must be avoided to increase the longevity of the
screen.

 The internal eMMC flash storage has a limited number of write cycles. Therefore it is

recommended that the amount of writing to flash is limited within software applications.1

 Always consider personal safety when installing and operating the device. For example, in

vehicle installations, CrossControl does not recommend that the device is being actively
operated by the driver when a risk of injury to people or damage to property is present.

3.5.1. Cleaning

To ensure proper and reliable functionality over time, pay attention to the following cleaning
instructions and precautions:

 Wipe the device clean from dirt using a soft damp cloth, preferably of microfiber type.

Larger amount of dry dust may be swept off using a soft brush before wiping clean.

 Avoid using alkaline, alcoholic or other potentially adverse chemicals for cleaning as doing

so may damage the device. However, small amount isopropyl alcohol may be used for
removing harsh stains.

 Avoid spraying or by other means applying larger amount of water or alcohol directly to

the device. Instead, lightly dampen a cloth before using it for cleaning the device.

1

The eMMC is used in pseudo SLC mode and implements both static and dynamic wear levelling to reach the

best reliability. The number of program/erase cycles is between 20k to 60k depending on the manufacturer and
temperature. Our recommendation for the application software is to temporary cache in RAM and to write larger
chunks of data to the eMMC. This recommendation is not specific to eMMC but is applicable to all flash
memories.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

11

 After cleaning, make sure that the device surface is left dry.
 Never use high-pressure air, vacuum, water or steam to clean the device.

3.5.2. Real time clock battery

Time and date information is stored in a memory sustained by an internal back-up battery.

The expected life time of the battery is approximately 20 years. The battery is not replaceable.

3.6. Transportation

When transporting the device it is recommended to use the original packaging. Make sure that
protective caps are used on all non-mated connectors. The storage temperature interval [-30°C to
+80°C] must be met.

3.7. Decommissioning

When the device has reached its end of life it should be handed over to the supplier or other
qualified party for recycling the product in an environmentally friendly manner. The manufacturer
does not handle decommissioning of the product.

4. Basic operation

This section covers basic operation of the device such as start-up, shut-down, display operation and
status notification.

Observe that the behavior of the on/off controls (on/off button and key switch signal) is user
configurable.

Button backlight is used for status notification while starting up, shutting down or when the device
is in rescue mode. Both button backlight and the buzzer is software controllable for notifications
from user applications.

See chapter 4.4 for details of button backlight status notification.

The buzzer is used for audible alerts as well as for various error notifications, see chapter 4.5 for
error code details.

4.1. Turning ON/OFF

The device can be turned ON or OFF from different actions as described in the following chapters.

To avoid data loss or corrupted flash memory, it is recommended that necessary data is saved and
user applications are properly closed before the device is shut down.

4.1.1. Key switch signal

The factory default way of turning the device ON or OFF is by the use of the vehicle’s ignition

switch.

Turning the vehicle’s ignition key to position ON will start the device.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

12

Turning the vehicle’s ignition key to position OFF will turn off the device.

4.1.2. On/off button

While in off-state, pressing and holding the on/off button will turn ON the device.

While the device is operating, pressing and holding the on/off button for 1 sec will turn OFF the
device.

4.1.3. Linux shutdown command

The device can be turned OFF by executing Linux shell shutdown commands, for example:

# s h ut do w n

4.1.4. Forced shutdown

If the device stops responding, a forced shutdown can be performed by pressing and holding the
on/off button until the device is switched off.

 The button press response time for the forced shutdown (long press) is user configurable

and the default value is set to 8 seconds.

It is not recommended to use the forced shut down unless absolutely necessary - since doing so will
immediately switch off all internal voltages, regardless of ongoing operations. Any information
which was not saved to flash memory will be lost when performing a forced shutdown. However, no
physical damage will be caused to the device by a forced shutdown.

4.2. Light sensor

The CCpilot VS 12” contains a light sensor that can be used to automatically adjust the display
brightness, depending on the ambient light conditions. As depicted in Figure 2, the light sensor is
located in the lower left corner of the front surface. When automated dimming is enabled, the level
of sensitivity can be adjusted.

The screen brightness can also be manually controlled directly from user applications through
APIs.

For proper operation it is important to keep the light sensor opening clean and with free visibility.

4.3. Using the touch screen

To reduce the amount of reflections when operating under sunny conditions, the touch screen’s
protective glass is covered with an anti-glare film. Do not use any sharp or abrasive objects when
interacting with the touch screen.

Basic usage of the capacitive touch screen should be intuitive for most users. Note that the touch
screen is capable of handling two simultaneous touches.

4.4. Status notification

The LED in the on/off button is used for status notification while starting up, shutting down or in
other operational states. The buzzer may also be used for user notifications. See Table 1 for a
description of the status notification behavior for different operational states.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

13

Table 1: LED and buzzer indication for different operational states

Operational state

LED indication

Buzzer notification

Device off

OFF

-

Power applied, device off

OFF

-

Starting up

Yellow flashing, 2 Hz

Short beep

Operating (started up)

Static green

-

Shutting down

Static green

-

Forced shutdown

Blue flashing, 2 Hz

short beep

Rescue mode, starting

Static orange

Short beep

Rescue mode, running

Green flashing, 2 Hz

Software upgrade

Yellow flashing, 0.5 Hz

-

4.5. Error codes

The LED in the on/off button is also used for indicating error codes by emitting a blue blinking
pattern after shutdown of the device. The device may be started again when in this mode, by the
button or the key switch signal. Depending on the nature of the error, the device may start or go
back into error indication.

When an error occurs, the device is immediately shut down and the error is reported by blinking a
specific number of times corresponding to an error code (see table of error codes). The blinks will
be in a continuous sequence of 1 Hz blinks, with a longer pause of two seconds after the specific
number of blinks, allowing the end user to count the number of blinks. Refer to Figure 1 below for
an example.

Figure 6: Example of the blinking pattern for error code 3

When an error occurs, an error code is also immediately saved to persistent storage (FRAM). If
several errors occur before the device it is shut down, only the code of the first error is saved and
reported. The error code in persistent storage can be read and cleared from a user application.
Refer to Table 2: CCpilot VS 12” error codes for a complete listing of the error codes.

The number of blinks is important information if the unit is sent in for service/repair.

Table 2: CCpilot VS 12” error codes

Error code

Error code name

Likely problem cause

1

errCodeReadErrEEPROM

Corrupted FRAM. Invalid values. FRAM
may need to be manually
reprogrammed or replaced.

2

errCodeWriteErrEEPROM

Corrupted FRAM. Invalid values. FRAM
may need to be manually
reprogrammed or replaced.

3

errCodeDriverInit

FRAM or light sensor malfunction.
Problem with cable to button/USB PCB.

4 - -

5

errCodeMPDoneTimeoutErr

Timeout waiting for the MP_DONE
signal – MP error. Boot loader missing.
Faulty or unprogrammed eMMC.

6

errCodeTimeOutWaitingForVoltages

Internal or external voltages did not
stabilize during start-up. Power supply

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

14

current limitation. Power cables not
thick enough (>1.5 mm2).

7

errCodeTEMPOutOfLimits

Internal PCB temperature above 95 °C
or temperature sensor malfunction

8 - - 9 - - 10

errCodeRCCInit

SS circuit malfunction (clocks).

11

errCodeSSState

Programming bug or faulty processor.

12

errCodeManageDiagnostics

Failed to save diagnostic data to
FRAM.

13

errCodeManageActDeAct

HAL_IO errors (SS internal).

14

errCodeTickTimeOutTimer

HAL_IO errors (SS internal).

15

errCodeOperateModeStateError

SS internal.

16

errCodeHALIOReadErr

HAL_IO errors (SS internal).

17

errCodeHALIOWriteErr

HAL_IO errors (SS internal).

18 -

19 -

20 -

21 -

22 -

23 -

24 -

25

errCode12VOutOfLimits

Internal 12V voltage out of limits during
operation.

26

errCode5VOutOfLimits

Internal 5V voltage out of limits during
operation.

27

errCode3V3AOutOfLimits

Internal 3V3A voltage out of limits
during operation.

5. Interface overview

This section describes the various interfaces of the device. Main part of these interfaces can be
accessed via software APIs. These are described in the CCpilot VS 12” Software Guide.

5.1. Front panel

5.1.1. Touch screen

The front panel contains a projective capacitive (PCAP) touch screen, which is capable of handling
two simultaneous touches.

5.1.2. Light sensor

There is a light sensor in the front panel used by user applications or used with the built in
automated function for dimming of the display brightness.

For light sensor location, see Figure 2. Refer to the CCpilot VS 12” Software guide for details about
accessing the light sensor data from user applications.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

15

5.2. Buzzer

There is a built-in buzzer that can be used for audible notifications. The buzzer is software
controllable with configurable volume and frequency.

For buzzer location see Figure 3. See chapter 4.4 for buzzer notification events. Refer to the CCpilot
VS 12” Software guide for details about controlling the buzzer from user applications.

5.3. Analog video input

There is a video input for connecting an analog video source such as a rear-view camera. Displaying
of analog video is handled in hardware with minimum impact on CPU load.

The analog video input supports a wide range of commonly used composite video formats (both
PAL and NTSC).

See chapter 7.1 for details.

For proper video performance and to ensure electromagnetic compatibility, 75 Ω coaxial cable shall
be used for connecting the video source. Preferably use coaxial cables of type M17/94-RG179. Refer
to chapter 3.3.1 for recommendations about connecting video coaxial cable.

It is important to supply the analog video source with a stable well-filtered supply voltage. Note
that video input grounds are internally connected with main supply ground. Precautions should be
made to avoid ground-loops between the video source and main supply ground which could affect
video quality. One way of avoiding ground-loop is to add video isolators or use a video source with
galvanic isolation between supply and signal ground.

5.4. CAN

CCpilot VS 12” has four CAN ports, supporting ISO 11898 CAN 2.0B protocol (29-bit extended
identifier) and bit rates up to 1 Mbps.

CCpilot VS 12" is compliant with AEF ISO 11783.

Note that Internal EMI filters on CAN High/Low signals have a capacitance of 100 pF (typ) which
deviates from the ISO 11898 standard and implies some limitations on the CAN bus topology
(maximum bus length, number of CAN nodes etc.) when running at high bit-rates, i.e. above 250
kbps.

The ports feature highly protected CAN transceivers which are tolerant for bus short-circuits to
main supply voltage and ground.

CAN shield connections are according to J1939-11 with capacitive coupling to ground. There is no
device-internal CAN bus termination, therefore bus termination must be applied externally.

5.5. Ethernet

CCpilot VS 12” has an Ethernet interface supporting 10BASE-T/100-BASE-TX/1000-BASE-T and
Auto-MDIX.

The Ethernet interface is galvanic isolated with 1.0 kVAC insulation voltage.

Shielded cables shall be used to ensure reliable communication and electromagnetic compliance.

As with all Ethernet enabled devices, connecting the device to a public network environment may
impose an IT security threat.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

16

5.6. USB

CCpilot VS 12” has in total four USB ports; two ports are located in the M12 connectors 3 and 4 at
the rear of the device, and two ports are located in the USB type A connectors on the left side, refer
to Figure 3 and Figure 4 for localization of the ports. They can be used for connecting USB storage
devices or other peripherals such as mouse, keyboard or various wireless interfaces. All USB-ports
are capable of both full-speed (12 Mbps) and hi-speed (480 Mbps) communication.

Note that the sealing property (IP classification) of the device is not retained when removing the
protective rubber lids for accessing the USB ports on the left side.

Each USB ports can supply up to 2A. The USB ports are internally over-current and short-circuit to
ground protected.

Shielded cables shall be used to ensure reliable communication and electromagnetic compliance.
Refer to chapter 3.3.1 for recommendations about connecting shield cables.

5.7. Analog input

CCpilot VS 12” has one fixed analog input 0-14V range with 12.7 kΩ input impedance to ground.

5.8. Configurable input

CCpilot VS 12” has one configurable input for a wide range of digital and analog measurements.
This input can be configured according to Table 3 below.

Table 3: Input configurations

Input modes

Configurations

Digital input modes

Digital input

Range

0-10V

Input configurations
Pull-down (ca 14 kΩ to GND)

Pull-up (ca 4,7 kΩ to Vin and 14 kΩ to
GND)

Input modes
Mode 1

low level ca 2,5 V

High level ca 3,4 V

Mode 2

low level ca 1,5 V

High level ca 6,3 V

Frequency measurement

Range

0.1-10 000 Hz

Input configurations
Pull-down (ca 14 kΩ to GND)

Pull-up (ca 4,7 kΩ to Vin and 14 kΩ to
GND)

Input modes
Mode 1

low level ca 2,5 V

High level ca 3,4 V

Mode 2

low level ca 1,5 V

High level ca 6,3 V

Analog input modes

Voltage measurement

Range

0-32V

For electrical specification at different input modes, see chapter 7.1.

Note that the input ground is internally joined with main supply ground. Precautions should be
made to avoid ground-loops between input ground and main supply ground. Ground-loop currents
may affect readings.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

17

The co-processor handles the configurable input and adds features such as averaging for frequency
measurements. Measurement results are accessible to user applications through software APIs.
Refer to the CCAux API documentation for programming details. Each input mode is described
more in chapters 5.8.1 and 5.8.2 below.

5.8.1. Digital input and frequency measurement

Digital and frequency input modes can be used for connecting simple logical signals (for example
switch to battery/ground or various logic output sensors) or frequency-output sensors commonly
used in industrial applications.

The input can be configured for two different logic signal levels thresholds and can be set as either
pull-down only or internal pull-up (together with the pull-down). This makes the input compatible
with a wide range of sensors with different output types and signal levels.

The selectable internal pull-up is sourced from the main supply input through internal over-voltage
protection. Therefore, pull-up will follow the main supply voltage but never exceed 55 VDC in case of
main voltage transients.

Frequency measurement is implemented by timer captures at a time-base of 72 MHz (100 ppm).
This time-base gives a theoretical frequency resolution of approximately 0.014 Hz at 1 kHz and 3.12
Hz at 15 kHz (better resolution at lower frequencies). Refer to the CCAux API documentation for
details about available configurations.

See chapter 7.1 for electrical characteristics such as absolute maximum voltage, digital threshold
levels, pull-up strength, frequency range and accuracy.

5.8.2. Voltage measurement

The input can be used for measuring DC-voltages in range of 0-32 V.

See chapter 7.1 for electrical characteristics such as impedance and accuracy.

5.9. High-side outputs

CCpilot VS 12” has six self-protected high-side digital outputs for switching various external loads
such as buzzers, relays, solenoids, lamps or other resistive or inductive loads.

The high-side output drivers are powered from the main supply voltage through internal over­voltage protection that limits the output voltage to 50 VDC (typ) in case of supply voltage transients.
Four of the outputs are specified for 400mA load and two are specified for 800mA load, but all use
the same technical solution. Each output is current-limited to 1200 mA per channel (typ).

Each output provides diagnostics/fault-detection for both ON- and OFF-state according to Table 4
below.

Table 4: Diagnostics and fault detection for high-side outputs

OFF-state

ON-state

Open load

-

Short to battery

- - Overload or short to ground

-

Over-temperature

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

18

To ensure long-term reliability, the fault-detection flags are continuously monitored and each
output is automatically switched OFF in case its fault flag is triggered in ON state. An output
switched OFF by a fault condition must be re-enabled by the user or user application.

Observe that high continuous load of the outputs generates internal heat in the device. At high
ambient temperatures, this may lead to outputs automatically switching off because of thermal
protection. Outputs can be re-enabled by the user (or user application) once the driver IC
temperature has decreased below its threshold. If output over-temperature shutdown occurs, it is
recommended to improve air ventilation around the device and if possible reduce the amount of
output load.

Output on/off control as well as fault monitoring is handled by a co-processor and controlled
through CCAux API.

See chapter 7.1 for electrical characteristics such as channel resistance, timing, current limit, and
fault-detection details.

5.10. RS-232

CCpilot VS 12” has two RS-232 ports, each supporting communication rates up to 115200 bps.

See chapter 7.1 for electrical characteristics such as protection voltages.

5.11. RS-485

CCpilot VS 12” has one RS-485 port, supporting communication rates up to 9600 bps.

The RS-485 configuration in CCpilot VS 12” comprises one A/B pair, i.e. full-duplex
communication is not supported.

See chapter 7.1 for electrical characteristics such as protection voltages.

5.12. Key switch signal

To simplify the cable harness design, CCpilot VS 12” has two input pins reserved for the key switch
signal. These pins are connected internally, i.e. any of the pins can be used. Refer to chapter 6.2 and

6.3 for pinout details.

6. Connectors

All external connectors are accessible from the rear or left side of the device.

The main connectors are the three 12-pin Deutsch DT series connectors, marked with letters A, B
and C and features keying (A-, B- and C-key respectively). The DT connectors are located to the left
of the rear side. To the right of the rear side there are three M12 connectors, marked with 3, 4 and
Eth. Finally, on the left side of the device there are two USB type A connectors marked 1 and 2.
These USB connectors are protected under a rubber sealing. Refer to Figure 7 for an overview of the
connectors.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

19

Figure 7: CCpilot VS 12” connectors

Connector pinouts are found in the following chapters.

6.1. Deutsch DT connectors, general

Use caution and avoid plugging/unplugging Deutsch DT connectors while the device is powered up.
If a connector pin becomes bent the interface may not function correctly and the device should be
returned to the manufacturer for repair.

Pay close attention to the coding; violence or excessive force should not be used when mating the
connectors.

Note that the pin-order 1-12 in tables below are oriented as when looking at the receptacles from
the rear of the CCpilot VS 12” device, i.e. pin 1 at top-left position and pin 12 at bottom-left position,
see Figure 8.

Figure 8: DT connector pinout

The connector pins are rated for 13 A continuous current.

The DT connector pins are made of tin-plated brass. It is recommended to use tin-plated
receptacles in the mating connectors. Using different plating in the cable connectors might cause
galvanic corrosion.

Note that all three Deutsch DT connectors must be mated with its corresponding cable connector or
a proper blind plug to maintain the IP-classification.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

20

6.2. Deutsch DT connector A pinout

Table 5: DT connector A pinout

DT Connector A

Matching plug: DT06-12SA (A-key)

Pin

Signal

Comment

1

Power supply

12 V or 24 V, see chapter 3.2.4 for information on
connection

2

High side output 1

(max 800 mA load)

3

High side output 2

(max 400 mA load)

4

CAN1 high

5 CAN1 low

6 CAN1 ground

7 CAN2 high

8 CAN2 low

9 CAN2 ground

10

Key switch signal

See chapter 3.2.4 for information on connection

11

Not connected

12

Ground

6.3. Deutsch DT connector B pinout

Table 6: DT connector B pinout

DT Connector B

Matching plug: DT06-12SB (B-key)

Pin

Signal

Comment

1

High side output 3

(max 800 mA load)

2

CAN3 high

3 CAN3 low

4 CAN3 ground

5 CAN4 ground

6 Analog input

7 Key switch signal

See chapter 3.2.4 for information on connection

8

Ground

9

Configurable input

10

CAN4 high

11

CAN4 low

12

Ground

6.4. Deutsch DT connector C pinout

Table 7: DT connector C pinout

DT Connector C

Matching plug: DT06-12SC (C-key)

Pin

Signal

Comment

1

High side output 4

Video supply (max 400 mA load)

2

Video IN

3 Video shield

Internally connected to supply ground

4

RS-485B

5 RS-485A

6 High side output 5

(max 400 mA load)

7

Spare

8 Spare

9 High side output 6

RS-232 supply (max 400 mA load)

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

21

10

RS-232 2 TxD

11

RS-232 2 RxD

12

Ground

6.5. M12 connectors, general

Pay close attention to the coding; violence or excessive force should not be used when mating the
connectors. The connectors are oriented so that an angled cable should be pointing downwards.
Refer to Figure 9 for pin orientation.

Figure 9: M12 connector pinout, A-coded to the left and X-coded to the right

The M12 connector pins/receptacles are made of gold-plated copper-zinc alloy. It is recommended
to use gold-plated pins/receptacles in the mating connectors. Using different plating in the cable
connectors might cause galvanic corrosion. The M12 contact body is made of polyamide and the
sleeve around it is made of nickel-plated zinc.

Note that all three M12 connectors must be mated with its corresponding cable connector or a
proper blind plug to maintain the IP-classification.

6.6. USB M12 connector pinout

Table 8: USB M12 connector pinout

USB M12 Connector

Matching plug: SACC-M12MS-5CON-PG 7-SH (male, 5-pin, A-coded)

Pin

Signal

1

VBUS

2

Data-

3

Data+

4

Ground

5

Ground

6.7. Ethernet M12 pinout

Table 9: Ethernet M12 connector pinout

Ethernet M12 Connector

Matching plug: SACC-MSX-8QO SH ETH SCO (male, 8-pin, X-coded)

Pin

Signal

1

TR0+

2

TR0- 3 TR1+

4

TR1- 5 TR3+

6

TR3- 7 TR2-

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

22

8

TR2+

6.8. USB Type A connectors, general

USB type A connectors do not meet the CCpilot VS 12” IP-classification unless the rubber lid is
closed. There is an inner sealing to prevent water and dust to enter the device via the USB type A
connectors. However, the connector itself might be damaged by water and dust, so make sure the
rubber lids always are closed when not using the connectors.

If the rubber lids should be damaged contact the supplier for replacement parts.

6.9. USB Type A pinout

Table 10: USB type A connector pinout

USB type A Connector

Matching plug: male, 4-pin, type A

Pin

Signal

1

VBUS

2

Data-

3

Data+

4

Ground

7. Specifications

7.1. Technical data

Temperature specification

Operating

-30 to +70 °C

Storage

-30 to +80 °C

Kernel

Main Processor

NXP™ i.MX6: ARM 32-bit, 1 GHz, Automotive, Quad core, Cortex®-A9

Co-processor

STMicroelectronics STM32F373, Cortex®-M4

Data storage

4 Gbyte, Industrial grade eMMC

(Note)

RAM memory

2 Gbyte, DDR3

Note: The eMMC is used in pseudo SLC mode and implements both static and dynamic wear levelling to

reach the best reliability. The number of program/erase cycles is between 20k to 60k depending on the
manufactures and temperature. Our recommendation for the application software is to temporary
cache in RAM and to write larger chunks of data to the eMMC. This recommendation is not specific to
eMMC but is applicable to all flash memories.

Power Supply

Supply voltage

Nominal
Extreme

12 VDC or 24 VDC

7.5 VDC…32 VDC

Power consumption

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

23

Typical, operating
Max, operating
Device without ext loads
4x USB @ max load
6x HS out @ max load
Shutdown

Vin = 12 VDC Vin = 24 VDC

17 W (typ) 17 W (typ)
143 W max 230 W max
17 W max 17 W max
40 W max 40 W max
86 W max 173 W max

0.44 mA (typ) 0.85 mA (typ)

Inrush current

Duration ca 60 ms

Vin = 12 VDC Vin = 24 VDC

< 8.5 A < 4.5 A

External fuse recommendation

Current rating

15 A* (including maximum external loads)

* This assumes that the fuse is in accordance with IEC 20127 i.e. can be continuously

operated at 100% of rated current.

CAN interfaces

Type

Non-isolated, ISO 11898-2, CAN 2.0B with cable shield decoupling
according to J1939-11.
Supports ISOBUS

CAN transceiver

NXP TJA1051T/3

Baud Rate

20 – 250 kbps (up to 1 Mbps)*

* Internal CAN bus filters have a capacitance of 100pF (typ) as stated in the J1939 specification. This

puts restrictions on the CAN bus topology considering bus length, number of CAN nodes etc. when

running at bit-rates higher than 250 kbps.

Protection

Short circuit protected to -32V to +32V

USB interfaces

Type

4x USB 2.0 compatible host ports

Two USB ports are available in M12 connectors, the remaining ports are USB type A connectors covered

by a removable rubber sealing. Device IP-classification is not retained when the USB sealing is removed.

Speed
Full-speed (12 Mbps) and Hi-speed USB (480 Mbps) is supported.

VBUS supply

According to USB specification, but with increased drive capacity

5.0 V, 2 A per port, internally over-current and short-circuit protected.

Ethernet

Type

Gigabit Ethernet compatible with 10BASE-T, 100BASE-TX and
1000Base-T Ethernet standards.
Auto-MDIX support.

Insulation voltage

1000 VAC, 50/60Hz for 1 minute.

Analog video

Number of inputs

1

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

24

Supported input signals

Composite video 75 ohm, PAL and NTSC

Protection

Video inputs are over-voltage protected up to +40 VDC.

Configurable Inputs

Number of inputs

1

Input voltage tolerance

+32.0 V (max), referred to main supply ground

- 32.0 V (min), referred to main supply ground

(inputting voltages greater than specified may damage the device)

Digital input levels mode 1
Rising threshold
Falling threshold
Hysteresis

applies to both Digital and Frequency modes

3.4 V (typ)

2.5 V (typ)

0.9 V (typ)

Digital input levels mode 2
Rising threshold
Falling threshold
Hysteresis

applies to both Digital and Frequency modes

6.3 V (typ)

1.5 V (typ)

4.8 V (typ)

Frequency measurement
Frequency range
Duty-cycle range

Time base
Accuracy

Input amplitude ranges according to above.

0.1 Hz – 10 kHz
40-60%

Exceeding above duty-cycle limits may cause inaccurate readings.

72 MHz (± 100 ppm)
± 0.50 % (typ) up to 15 kHz

Input jitter (pulse time variations) will affect accuracy, especially at high frequencies.

Input impedance with pull­up enabled

4.7 kΩ (± 2 %) to main supply voltage and 14.04kΩ (± 2 %) to ground.

Input impedance with pull­up disabled

14.04kΩ (± 2 %) to ground.

Voltage measurement
Range (min)
Accuracy
Resolution
Input Impedance

0 – 32.0 VDC
± (2% + 40 mV)
8 mV
14,04kΩ (± 2 %)

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

25

High-side digital outputs

Number of channels

6

Current limit
Initial peak current
Repetitive short-circuit

1200 mA (typ) (min 700 mA, max 2000 mA) per channel
1000 mA (typ).

Diagnostics

OFF state diagnostics
ON state diagnostics

Built-on diagnostics and fault flag monitoring.

To ensure long-term reliability, the fault flags are continuously monitored and each output is

automatically switched OFF in case the fault flag is triggered in ON state.

Open load, short to battery
Over-load (or short to GND), over-temperature

Open-load detection
Internal pull-up current
Threshold voltage

5 µA (typ)

2.0 V (typ) (min 1.5V, max 3.5V)

Open load is detected when output voltage rises above the threshold voltage in OFF state.

Short-circuit detection
Voltage threshold

2.8 V (typ)

Over-current is detected when output voltage falls below the threshold voltage in ON state.

Over-temp. detection
Turn-off Threshold
Hysteresis

+175 °C typ (min 150 °C, max 200 °C)
10 °C

ON-state resistance

400 mΩ (typ), 700 mΩ (max)

Slew rate
Turn ON:
Turn OFF:

80 µs (typ), 180 µs (max)
80 µs (typ), 200 µs (max)

OFF-state leakage

5 µA (typ)
12 µA (max)

Buzzer

Frequency range

1 – 20 kHz (SPL peak at 3200 Hz)

SPL

85 dBA at 1 meter (typ, 3200 Hz)

The buzzer is located on the back (connector side) of the device and the effective SPL varies

dependent on the acoustic properties of the installation environment.

Button and Status notification

On/off button

On/off button with backlight and tactile feedback.

Status notification

Button backlight is used for status notification, such as blinking at 2 Hz
during start-up, etc.

Software

Operating system

Yocto Linux, Kernel version 4.1.38

Additional software

CCAux API. Refer to the CCpilot VS Software Guide and
Programmer’s guide for details.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

26

Display

Size
Diagonal size
Active area
Pixel pitch

12.1 inch widescreen

261.12 x 163.2 mm
204 x 204 µm

Type
Aspect ratio
Resolution
Colour depth
Contrast ratio
Viewing angle

TFT
16:10
WXGA, 1280x800
24 bit (16.7 million colors)
450:1 (min), 700:1 (typ)
Horizontal: ± 80°
Vertical: -60° -- +80°

Backlight
Type
Brightness
LED Life time

LED
1080 cd/m2 (min), 1350 cd/m2 (typ)
80 000 h (min), 100 000 h (typ) before brightness is reduced with 50 %
(when operated with full brightness at 25 °C)

(Note that higher operating temperatures affects LED life time.)

Touch-screen
Type
Simultaneous touches
Protective glass thickness
Coating
Surface Hardness

Optically bonded
Projective capacitive touch panel (PCAP)
2

1.8 mm
Clear and CS (chemically strengthened)
5H

7.2. Environmental specifications

Environmental Test

Test standard

Notes

Dry Heat

IEC 60068-2-2:2007

Operating: +70°C, 24h
Storage: +80°C, 16h

Damp Heat

IEC 60068-2-30:2005

Operation: +25°C / +55°C
>90% RH 2*24h

Cold

IEC 60068-2-1:2007

Operating: -30°C, 24h
Storage: -30°C, 24h

Change of temperature

IEC 60068-2-14:2009

-30°C to +70°C, 5°C/min
3hr hold time, 20 cycles

Vibration

IEC 60068-2-64:2008

0.005 g2/Hz 10 Hz

0.005 g2/Hz 260 Hz

0.002 g2/Hz 350 Hz
3x8h

Shock

IEC 60068-2-27:2008

± 15 g / 11ms 3x1000 impulses

Enclosure Ingress Protection

IEC 60529:2014

IP65

Any changes or modifications to the device not expressly approved by CrossControl could void the
environmental classification, warranty, and user's authority to operate the equipment.

7.3. EMC specification

The CCpilot VS 12” device has been tested for Electromagnetic Compatibility according to the
following standards.

EMC Test

Test standard

Notes

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

27

Electrical Transients

ISO 7637-2:2011
12 V system

24 V system

Pulse Level
1 -25V
2 +25V
3a -25V
3b +25V
4 -4V
5 +26,5V, Ri = 2Ω

1 -450V
2a +37V
2b +20V
3a -150V
3b +150V
4 -12V
5 +123V, Ri = 2Ω

ESD immunity

ISO 10605:2008, EN 61000-4-2

Air ± 8 kV
Contact ± 6 kV

Radiated RF immunity

(1)

ISO 11452-2:2004

MHz Level Modulation
200-2000 30 V/m 80%AM, 1kHz

Induces RF immunity

(1)

ISO 11452-4:2005/Cor.1:2009
(BCI)

MHz Level Modulation
20-200 60 mA 80%AM, 1kHz

Radiated RF emission

(1)

ISO 13309:2010

Narrow-b. Broad-b.
MHz dBµV/m dBµV/m

30-75 54-44 64-54
75-400 44-55 54-65
400-1000 55 65

(1) Compliance to RF immunity and RF emission standards require use of shielded cabl es for Ethernet, USB and Video interfaces.

EMC tests are performed at 24 VDC supply voltage unless other levels are specified in test standards.

System level compliance to EMC standards may be affected by external factors like mounting,
omitting the use of shielded cables etc.

7.4. Weight and dimensions

Attribute

Description

Comments

Dimensions

312 x 213 x 66 mm

(W x H x D)

Weight

2.0 kg

Mounting holes
Spacing
Thread dimension
Thread depth

VESA75
75 mm
M5
8 mm

Enclosure material

Glass fiber reinforced
polyamide

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

28

Figure 10: CCpilot VS dimensions.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

29

Technical support

Contact your reseller or supplier for help with possible problems with your device. In order to get
the best help, you should have your device in front of you and be prepared with the following
information before you contact support.

 Part number and serial number of the unit, which you find on the identification label, see

Figure 1.

 Date of purchase, which is found on the invoice.
 The conditions and circumstances under which the problem arises.
 Error codes signaled by the status LED
 Possible error messages which are shown.
 Device log files (if possible).
 Information regarding possible external equipment which is connected to the device.

 Additional sources of information are available on the CrossControl support site:

http://support.crosscontrol.com

Trademarks and terms of use

© 2017 CrossControl

All trademarks sighted in this document are the property of their respective owners.

- NXP™ is a trademark of NXP Semiconductors Inc.

- Arm® is a registered trademark of ARM Limited.

- Linux® is a registered trademark of Linus Torvalds in the U.S. and other countries.

- CrossControl and CCpilot are trademarks of CrossControl AB.

CrossControl is not responsible for editing errors, technical errors or for material which has been
omitted in this document. CrossControl is not responsible for unintentional damage or for damage
which occurs as a result of supplying, handling or using of this material including the devices and
software referred to herein. The information in this handbook is supplied without any guarantees
and can change without prior notification.

For CrossControl licensed software, CrossControl grants you a license under CrossControl
intellectual property rights to use, reproduce, distribute, market and sell the software, only as a part
of or integrated within, the devices for which this documentation concerns. Any other usage, such
as, but not limited to, reproduction, distribution, marketing, sales and reverse engineer of this
documentation, licensed software source code or any other affiliated material may not be
performed without written consent of CrossControl.

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

30

CrossControl respects the intellectual property of others, and we ask our users to do the same.
Where software based on CrossControl software or products is distributed, the software may only
be distributed in accordance with the terms and conditions provided by the reproduced licensors.

For end-user license agreements (EULAs), copyright notices, conditions, and disclaimers,
regarding certain third-party components used in the device, refer to the copyright notices
documentation.

Index

Ambient light sensor, 12, 14
Analog input, 16
Analog video, 15, 23
Application example, 8
Backlight, 26
Basic operation, 11
Battery, 11
Button, 12, 25
Buzzer, 15, 25
Cable installation, 9
CAN, 15, 23
Care, 10
Cleaning, 10
Clock, 11
Coaxial cables, 9
Configurable input, 16, 24
Connectors, 18
Contact, 29
Conventions, 4
CPU, 22
Decommissioning, 11
Device overview, 5
Digital input, 17
Dimensions, 27
Display, 26
Document conventions, 4
DT connector A pinout, 20
DT connector B pinout, 20
DT connector C pinout, 20
DT connectors, 19
Electrical specifications, 22
EMC specification, 26
eMMC, 22
Environmental resistance, 4
Environmental specifications, 26
Error codes, 13
Ethernet, 15, 23
Ethernet M12 pinout, 21
Example, 8
External interfaces, 18
Forced shutdown, 12
Frequency measurement, 17
Front panel, 14
Front side view, 5
Fuse, 7
Fuse recommendation, 22
Glass, 26
Handling, 7, 10
High-side outputs, 17, 25

I/O, 16, 17, 24
Identification, 4
Ignition key, 8, 11, 18
Inputs, 16, 18, 24
Inrush current, 22
Installation, 7, 9
Interface overview, 14
Introduction, 4
ISOBUS, 23
Key switch, 8, 11, 18
Left side view, 6
Light sensor, 12, 14
Linux shutdown command, 12
M12 connectors, 21
Maintenance, 10
Mounting, 7
On/Off button, 12
Operating temperature, 22
Operation, 11
Outputs, 17, 18, 25
Overview, 5
PCAP, 12, 14, 26
Pinout, 20, 21, 22
Ports, 18
Power consumption, 22
Power supply, 7, 22
Protective glass, 26
RAM memory, 22
Rear side view, 6
Recycling, 11
RS-232, 18
RS-485, 18
RTC, 11
Shields, 9
Shutdown, 11
Size, 27
Software, 25
Special considerations, 9
Specifications, 22
Start-up, 11
Status notification, 12, 25
Storage, 22
Support, 29
Technical data, 22
Technical support, 29
Temperature specification, 22
Terms of use, 29
TFT, 26
Touch screen, 12, 14, 26

CCpilot VS 12”

Product revision: A

Technical Manual

2017-11-23

www.crosscontrol.com

31

Trademarks, 29
Transport, 11
Turning OFF, 11
Turning ON, 11
USB, 16, 23
USB M12 connector pinout, 21
USB type A connectors, 22

USB type A pinout, 22
Weight, 27
Video, 23
Video input, 15
Wire gauge, 7
Voltage, 22
Voltage measurement, 17