Crosley CAE25ESR2, FAS257R2A2, FAM187R2A1, CAE25ESR1, FAM18HR2A1 Installation Instructions Manual

For Heavy

Median {FAM

Instructions

Duty {/:AS Models) and

Models) Air Conditioners

Please read ALL instructions be_hre installing.Two people are

recommended to install this prodaetdf a new electrical outlet

is reqaired,have the outlet installed by a qaalified electrician
be_re installing anit. See#5 in Prdiminary lnstraetions

_bllowing.

Preitiminary

Do the _bHowiog be_bre startiog to iostall aoR.See illustrations
bdow.

Check dimensions of your unit to determine model type:

Heavy duD' (FAS) Median (FAM)

Unit Height: 18.5/8" 17.5/8"
Unit Width: 26 1/. 23 1/.

Min. Window Opening: 19" 18 72"
Min. Window Width: 31" 26 1/,,
Max. Window Width: 43" 40 1/2"

1°

Check window opening size =the mounting parts furnished
with this air conditioner arc made to install in a wooden

sill double-hung window.The standard parts are for

window dimensions listed aboveX)pen sash to a minimum

of i9"(483mm). (FIG. i)

2. Cheek condition of window =all wood parts of window
must be in good shape and able to firmly hold the needed

sorer s.If not, make repairs before installing uniL

FIG. 1

SASH

1/2" MIN

T

19"MIN

1

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

SIDE RETAINER /

BRACKET

3_

Check your storm windows =if your storm window

*?ame does not allow the clearance required, correct by

adding a piece of wood as shown in FIG.2, or by removing
storm window while room air conditioner is being installed.
(continued)

FIG. 2

SASH

t

19" MIN

1/2" MIN i 1 1/2"MIN

I _ ENTIRESTOOL,FASTEN

STORM WINDOW FRAME OR WITH TWO NAILS OR
OTHER OBSTRUCTION SCREWS.

P/N 66121623

4. CHECK FOR ANYTHING THAT COULD BLOCK
AIRFLOW- check area outside of window for things

such as shrubs, trees, or awnings. Inside, be sure
flu_nimre, drapes, or blinds will not stop proper air flow.

5. Check the avaiiaNe deetrkai service - power suppb_ must

be the same as that shown on the unit serial nameplate.

(See Owner's Guide fbr serial plate location. _Power cold
is 48"long. Be sure you have an outlet near.

Too s Nequired

a large flat blade screwdriver
tape uleasure
adjustable wrench or pliers
pencil

Level
Socket wrenches

Phillips screwdriver

All models have a 3-prong sel_Ace phlg to provide proper

sel_/ice and sate positive groudmg. Do not change plug m
any way. Do not use an adapter plug. If your present wall
outlet does not match your plug, call a qualified electlician
to make the needed change.

NC Avoid ISlehazad or electric
shock. Do not use m_extension cord or gm
adaptor phlg. Eb not remove _uLvprong fi_om
the power cord.

Groundhog type wall
receptacle

./ .............................................................

circul

re o,

_, grou_

plug and current

detection device

6. Careful b, unpack air conditioner - remove all packing

material. Protect floor or carpet ti_om damage. Two
people should be used to move and install unit.

Hardware {in plastic bag)

,_ Washer Head

Locking Screw

For window panels

3/4" Long Hex°Head Screw

Safety Lock

@_ 1/2" Long Screw

and locknut

__ 3/4" Long Flat

Head Bolt and

Locknut

Sill Angle Bracket

Long hex-head

locking screw %r

top angle, side
retainer 5/16"

Long

Qty.

2

4 ea.

2 ea.

10

Remove Chassis

1. 1hill down ftont panel axt remove filter. (See FIG. !).

2. Lift ftont upwards and place to one side.

lnstatm Top Angl÷

and Side Bracket

Attach tbam gasket to top angle above holes as

shown in FIG. 6.

3. Locate file fimr flont screws _mdremove. These screws will
be needed to re=install the flont later. (See f'IG.2)

4. PU away flont flom cabinet sides as per photo (see FIG.3)

5. Gently lift flont offunit and place to one side (See FIG.4).

2. Install top
gmgk grad

side retainers

to cabinet as
shown in FIG. 6.

2.

6. Remove shipping crews flom top ofumt gradalso on the side
by the base if installed.

7. Hold the cabinet wNle pulling on the base hgmdle, gradcare-
fillly lemove the unit.

8. Add two i[)_un inserts to holes in top of cabinet where

shipping screws were removed flom.

Assemble Window

Fill÷r Panels

Place cabinet on floor, a bench, or a table.

Slide 'T' section of window filler panel into side retainer

on the side of the cabinet (see Figures 7°8). Do both
sides.

FIG. 7

PLASTI( \r_TNDOV, FILLER

FRAME PANEL

9. Your unit may come wifil internal packaging.THIS
PACKAGING MUST BE P,EMOVED PRI()R T()
INSTALLING THE AIR C()NDITIONER BACK

INT() THE CABINET. (See HG. 5)..

FIG. 8

d

[3

SIDE

RETASNER

i AIR ( O)q)ITIONE_

CABE','ET

TOP

VIEW

T' SECTION

PLASTIC

FRAME

WENT)OW HOLE

FILLER

PANEL