Crosley CT14NKXHN00, CT14NKXHW00 Owner’s Manual
TOP-MOUNT
REFRIGERATOR
REFRIGERATEUR
SUPERPOSE
A_ I "'+,[]X I< ='= °
ol0d ........d ul,/:_,al@_
Table of Contents/Table des matieres ..........2
2202007A
www.crosley.com
TABLEOF CONTENTS
TABLEDESMATIERES
REFRIGERATOR SAFETY ............................................... 3
PARTS AND FEATURES ..................................................4
INSTALLING YOUR REFRIGERATOR .............................. 5
Unpacking Your Refrigerator ........................................... 5
Space Requirements ....................................................... 5
Electrical Requirements ................................................... 6
Connecting the Refrigerator to a Water Source ............ 6
Reversing the Door Swing ............................................... 8
Reversing the Door Handles ........................................... 9
Door Closing and Alignment ......................................... 10
Understanding Sounds You May Hear ......................... 10
USING YOUR REFRIGERATOR ....................................... 11
Ensuring Proper Air Circulation ..................................... 11
Setting the Control ......................................................... 11
Adjusting Control Settings ............................................. 12
Food Storage Guide ....................................................... 12
REFRIGERATOR FEATURES ........................................... 14
Drop-in Door Trim .......................................................... 14
Refrigerator Shelves ...................................................... 14
Crisper and Crisper Cover ............................................. 14
Ice Maker Operation ...................................................... 15
CARING FOR YOUR REFRIGERATOR ........................... 16
Cleaning Your Refrigerator ............................................ 16
Changing the Light Bulb ................................................ 16
Power Interruptions ....................................................... 17
Vacation and Moving Care ............................................ 17
TROUBLESHOOTING ....................................................... 18
ASSISTANCE OR SERVICE ............................................. 21
WARRANTY ....................................................................... 22
SECURITE DU REFRIGERATEUR ................................. 23
PIECES ET CARACTERISTIQUES ................................. 24
INSTALLATION DU REFRIGERATEUR .......................... 25
D(_ballage de votre r(_frig(_rateur ................................... 25
Espacement requis ........................................................ 25
Sp(_cifications (_lectriques ............................................. 26
Raccordement du r(_frig(_rateur
une canalisation d'eau ................................................... 26
Inversion du sens d'ouverture des portes .................... 28
Inversion des poign(_es de porte .................................. 29
Fermeture et alignement des portes ............................ 30
Les bruits de I'appareil que vous pouvez entendre .... 31
UTILISATION DU REFRIGERATEUR .............................. 31
Pour s'assurer d'une circulation d'air appropriee ....... 31
Reglage des commandes .............................................. 32
Ajustement des r(_glages de commande ..................... 32
Guide d'entreposage des aliments ............................... 33
CARACTERISTIQUES DU REFRIGERATEUR ................ 34
Tringle d(_pos(_edans la porte ...................................... 34
Tablettes du refrig(_rateur .............................................. 34
Bac a I(_gumes et couvercle .......................................... 35
Utilisation de la machine a gla(;ons .............................. 36
ENTRETIEN DE VOTRE REFRIGERATEUR ................... 37
Nettoyage du r(_frig(_rateur ............................................ 37
Remplacement de I'ampoule d'(_clairage ..................... 38
Pannes de courant ......................................................... 38
Entretien avant les vacances ou
Iors d'un d(_m(_nagement .............................................. 39
DEPANNAGE ..................................................................... 40
ASSISTANCE OU SERVICE ............................................. 43
GARANTIE ......................................................................... 44
REFRIGERATORSAFETY
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This symbol alerts you to hazards that can kill or hurt you and others.
All safety messages will be preceded by the safety alert symbol and the word "DANGER" or
This is the safety alert symbol.
"WARNING." These words mean:
You will be killed or seriously injured if you don't
follow instructions.
You can be killed or seriously injured ifyou don't
follow instructions.
All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic
precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before servicing.
• Replace all panels before operating.
• Remove doors from your old refrigerator.
• Use nonflammable cleaner.
• Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
• Use two or more people to move and install
refrigerator.
• Disconnect power before installing ice maker.
• Use a sturdy glass when dispensing ice or water (on
some models).
SAVETHESE INSTRUCTIONS
ProperDisposalof
YourOld Refrigerator
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or
brain damage.
IMPORTANT - Child entrapment and suffocation are not
problems of the past. Junked or abandoned refrigerators
are still dangerous - even if they will sit for "just a few
days." If you are getting rid of your old refrigerator, please
follow these instructions to help prevent accidents.
Before you throw away your old refrigerator or freezer:
• Take off the doors.
• Leave the shelves in place so that children may not
easily climb inside.
PARTSAND FEATURES
This manual covers several different models. The refrigerator you have purchased may have some or all of the items listed.
The location of the features may not match your model.
9
4
I
5
1. Ice Cube Trays
2. Temperature Control and Light Switch Panel
3. Model and Serial Number Label
4. Adjustable Wire Shelves
5. Crisper Cover
6. Crisper Drawers
.... 11
7. Leveling Rollers (not shown)
8. Freezer Door Shelves
9. Magnetic Door Gaskets
10. Dairy Compartment
11. Door Shelves
INSTALLINGYOUR
REFRIGERATOR
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion,
or fire.
Removing Packaging Materials
• Remove tape and any labels from your refrigerator
before using (except the model and serial number
label).
To remove any remaining tape or glue, rub the area
briskly with your thumb. Tape or glue residue can also
be easily removed by rubbing a small amount of liquid
dish soap over the adhesive with your fingers. Wipe
with warm water and dry.
Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove tape
or glue. These products can damage the surface of
your refrigerator. For more information, see
"Refrigerator Safety" section.
On some models, shelves, bins, door shelf rails, and
other feature parts may be packaged in the Finishing
Touches TM FeaturePak. Follow the instructions
contained in the package for proper assembly.
IMPORTANT:
• Depending on your model, do not remove any
permanent instruction labels inside your refrigerator, or
the Tech Sheet that is fastened behind the base grille.
Depending on your model, do not remove the white
Styrofoam insert that is located behind the control
panel on the ceiling of the refrigerator. The insert is part
of the refrigerator and not part of the packing material.
If the insert is removed, ice may migrate down from the
freezer and cause icicles to form.
To ensure proper ventilation for your refrigerator, allow
for a .5" (1.25 cm) space on each side
Allow 3" (7,5 cm) of space between overhead cabinets
and refrigerator top.
Allow at least 1" (2.5 cm) between back of cabinet and
the wall.
II I
JI I
• If your refrigerator has an ice maker, make sure you
leave some extra space at the back for the water line
connections.
If you are installing your refrigerator next to a fixed wall,
leave 2" (5.08 cm) minimum on the hinge side
(depending on your model) to allow for the door to
swing open.
• Level the refrigerator (See "Door Closing and
Alignment").
NOTE: Do not install the refrigerator near an oven, radiator,
or other heat source, nor in a location where the
temperature will fall below 40° F (5° C).
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
*_s ,,_.... ,,_, _,_ ,_ '_ ,,, _ ....... ,, ,z_ ,,_
Read all directions carefully before you begin.
IMPORTANT:
• If operating the refrigerator before installing the water
connection, turn ice maker to the OFF position to
prevent operation without water.
• All installations must be in accordance with local
plumbing code requirements.
• Use copper tubing and check for leaks.
• Install copper tubing only in areas where temperatures
will remain above freezing.
• It may take up to 24 hours for your ice maker to begin
producing ice.
Tools required:
• Standard screwdriver
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection:
@
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused,
grounded electrical supply is required. It is recommended
that a separate circuit serving only your refrigerator be
provided. Use an outlet that cannot be turned off by a
switch. Do not use an extension cord.
NOTE: Before performing any type of installation, cleaning,
or removing a light bulb, turn the control, (Thermostat,
Refrigerator or Freezer Control depending on the model) to
OFF and then disconnect the refrigerator from the
electrical source. When you are finished, reconnect the
refrigerator to the electrical source and reset the control
(Thermostat, Refrigerator or Freezer Control depending on
the model) to the desired setting.
• 7Ae-inchand V_-inch open-end wrenches or two
adjustable wrenches
• V4-inch nut driver
• V4-inch drill bit
• Hand drill or electric drill (properly grounded)
NOTE: Your refrigerator dealer has a kit available with a
_A-inch saddle-type shut-off valve, a union, and copper
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes. Do not use a
piercing-type or sA_-inch saddle valve which reduces water
flow and clogs more easily.
Cold Water Supply
The ice maker water valve contains a flow washer which is
used as a water pressure regulator. The ice maker needs to
be connected to a cold water line with water pressure
between 30 and 120 psi. If a problem occurs, call your
utility company.
Connectingto water line:
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet
long enough to clear line of water.
3. Find a 1/2-inchto 11/4-inchvertical COLD water pipe
near the refrigerator.
NOTE: Horizontal pipe will work, but the following
procedure must be followed: Drill on the top side of the
pipe, not the bottom. This will help keep water away
from the drill. This also keeps normal sediment from
collecting in the valve.
To determine the length of copper tubing you will need,
measure from connection on lower left rear of
refrigerator to water pipe. Add 7 feet (2.1 m) to allow for
moving refrigerator for cleaning. Use 1/4-inchO.D.
(outside diameter) copper tubing. Be sure both ends of
copper tubing are cut square.
5. Using a grounded drill, drill a 1/4-inchhole in the cold
water pipe you have selected.
Connecting to refrigerator:
NOTE: The first step for connecting the water line to your
refrigerator is different depending on the type of water
valve provided with your refrigerator. See the diagrams
below to determine the style of valve you have. (On kit
models, assemble water valve to refrigerator per kit
instructions.)
1.
For Style 1, disconnect the tube clamp on the back of
the product and insert the copper tubing through the
clamp, as shown. Remove the tape label from the valve
inlet and insert copper tubing until it bottoms out
(approximately C\v-inch). Tighten nut by hand as much
as possible; then turn the nut an additional Z\x turn
using awrench. Do not overtighten. Re-attach the tube
clamp and tube to the back of the cabinet. Skip to
Step 2.
For Style 2, disconnect the tube clamp on the back of
the product and insert copper tubing through the
clamp as shown. Attach the copper tube to the valve
inlet using a compression nut and sleeve as shown.
Tighten the compression nut. Do not overtighten. Re-
attach the tube clamp and tube to the back of the
cabinet. Move to Step 2.
2. Turn shut-off valve ON. Check For Leaks. Tighten
any connections (including connections at the
valve) or nuts that leak.
1,Cold Water Pipe
2. Pipe Clamp
3, Copper Tubing
4, Compression Nut
5, Compression Sleeve
6, Shut Off Valve
7, Packing Nut
6.
Fasten shut-off valve to cold water pipe with pipe
clamp. Be sure outlet end is solidly in the 1/4-inchdrilled
hole in the water pipe and that washer is under the pipe
clamp. Tighten packing nut. Tighten the pipe clamp
screws carefully and evenly so washer makes a
watertight seal. Do not overtighten or you may crush
the copper tubing, especially if soft (coiled) copper
tubing is used. Now you are ready to connect the
copper tubing.
Slip compression sleeve and compression nut on
copper tubing as shown. Insert end of tubing into outlet
end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not
overtighten.
8.
Place the free end of the tubing into acontainer or sink,
and turn ON main water supply and flush out tubing
until water is clear. Turn OFF shut-off valve on the water
pipe. Coil copper tubing.
Style I
2
1, Tube Clamp
2. Copper Tubing
3. Compression Nut
4. Valve Inlet
Style 2
To remove doors from hinges:
I. Keep doors closed until ready to lift free from the
cabinet.
1
I
2
t22222)
C===)
CZZ3
(222223
C222:3
1. Tube Clamp
2. Copper Tubing
3. Compression Nut
The ice maker is equipped with a built-in water strainer.
If local water conditions require periodic cleaning or a
well is your source of water supply, a second water
strainer should be installed in the 1/4-inchwater line.
Obtain a water strainer from your nearest appliance
dealer. Install at either tube connection.
2. Start at the top hinge and work your way down to the
center hinge and bottom hinge. Remove all screws and
components as shown.
3. Open and lift doors off hinges.
NOTE: If you are reversing the door swing, you should
move the handles while the doors are off of the refrigerator.
Follow the instructions in the "Reversing the Door
Handles" section.
To replace doors on hinges:
1. Remove hole plugs covering the screw holes on the
opposite side of the refrigerator using a flat putty knife.
2. Replace the doors.
3. Start at the bottom hinge and work your way up to the
center hinge and top hinge replacing all components
and screws as shown.
4,
Line up doors so they are centered between the sides
of the cabinet and parallel with each other.
5.
Fill all unused openings with screws or plastic hole
plugs. Moisture will enter any unfilled openings.
NOTE: If the doors are not closing on their own, see
the "Door Closing and Alignment" section.
Top Hinge
4. Plug in refrigerator or reconnect power.
TOOLS NEEDED:
%6-inch hex-head socket wrench, No. 2 Phillips
screwdriver, flat-head screwdriver, 1/2-inch open-end
wrench, flat 2-inch putty knife.
5/16inch Hex-Head Hinge Screw
Door Stop Screw
Sealing Screw (use on top of doors)
SUGGESTION: Reversing the door swing should be
performed by a qualified person.
IMPORTANT: Before you begin, turn the refrigerator OFF,
unplug it, and remove any food from door shelves.
1.Hex-Head Hinge Screws
2. Top Hinge
3. Spacer
4. Sealing Screws
Center Hinge
3. Remove refrigerator handle assembly as shown. Keep
all parts together.
To reinstall freezer handle:
1
2
3
4
1,Door Stop
2. Door Stop Screw
3. Center Hinge
4, Hex-Head Hinge Screws
5, Sealing Screws
Bottom Hinge
1. Position freezer handle on the opposite side of the
freezer door and install top two screws.
2. Install the bottom two screws.
3. Tighten all screws.
To reinstall refrigerator handle:
1. Unscrew the hole plug in the refrigerator door and
screw it into place on the opposite side.
2. Position the refrigerator handle on the refrigerator door
and attach it at the top with two screws.
3. Align the lower portion of the handle and attach it to the
refrigerator with one screw.
4. Position screw cover over the screw and push it until it
snaps into place.
3
2
3
1,Door Stop
2. Door Stop Screw
3. Bottom Hinge
4, Hex-Head Hinge Screws
Cone Screw (Useon Topand Bottom of
Handle Screw (Use on Front of Handles)
To remove handles:
Handles)
Countersink Screw
8
1,Plugs
2. Countersink Screw
3, Top Endcap
4, Stick on Shim
5, Bottom Endcap
5, Handle Screw
7, Screw Cover
8, Plug
I I
5
6
Z
1
1. Remove freezer handle assembly as shown. Keep all
parts together,
2. Pry off screw cover and remove screw.
9
Your refrigerator has two front adjustable rollers - one on
the right and one on the left. If your refrigerator seems
unsteady or you want the doors to close easier, adjust the
refrigerator's tilt using the instructions below:
Roll out the refrigerator and use a level to check the
floor at the back from side-to-side. If needed, use
shims to level the back of the refrigerator if it is uneven.
Roll the refrigerator back into place with the rear rollers
on top of any shim(s) used so that the rear of the
refrigerator is level.
With the rear already level and the refrigerator in place,
use the bottom leveling screws to level the refrigerator
from side-to-side. They are part of the front roller
assemblies, which are found at the base of the
refrigerator on either side.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws
and rollers. This makes it easier to adjust the screws.
To level your refrigerator, you may either turn the screw
clockwise to raise that side of the refrigerator or turn
the screw counterclockwise to lower that side. Place a
level on top of the refrigerator to check adjustments.
If the doors do not close on their own, you will need to
raise the front of the refrigerator so it is slightly higher
than the back. To do this, turn both leveling screws
clockwise 1/2turn.
I/..Jl,.l = = 1 J,j/l_t _
Your new refrigerator may make sounds that your old one
didn't make. Because the sounds are new to you, you
might be concerned about them. Most of the new sounds
are normal. Hard surfaces, like the floor, walls, and
cabinets, can make the sounds seem louder than they
actually are. The following describes the kinds of sounds
and what may be making them.
• If your product is equipped with an ice maker, you will
hear a buzzing sound when the water valve opens to fill
the ice maker for each cycle.
The defrost timer will click when the automatic defrost
cycle begins and ends. Also, the Thermostat Control
(or Refrigerator Control depending on the model), will
click when cycling on and off.
• Rattling noises may come from the flow of refrigerant,
the water line, or items stored on top of the refrigerator.
Your refrigerator is designed to run more efficiently to
keep your food items at the desired temperature. The
high efficiency compressor may cause your new
refrigerator to run longer than your old one, and you
may hear a pulsating or high-pitched sound.
• Water dripping on the defrost heater during a defrost
cycle may cause a sizzling sound.
• You may hear the evaporator fan motor circulating the
air through the refrigerator and freezer compartments,
• As each cycle ends, you may hear a gurgling sound
due to the refrigerant flowing in your refrigerator.
• Contraction and expansion of the inside walls may
cause a popping noise.
• You may hear air being forced over the condenser by
the condenser fan.
• You may hear water running into the drain pan during
the defrost cycle.
IMPORTANT: Be sure to turn both screws an equal
amount or the refrigerator will no longer be level side-
to-side.
5,
Open doors and check if they close automatically. If
not, repeat steps 3 and 4.
6.
Using a level, check to see if the refrigerator is still level
side-to-side. Readjust if necessary.
10
USING YOUR
REFRIGERATOR
In order to ensure proper temperatures, you need to permit
air flow between the refrigerator and freezer sections. As
shown in the illustration, cool air enters through the bottom
of the freezer section and moves up. Most of the air then
flows through the freezer section vents and recirculates
under the freezer floor. The rest of the air enters the
refrigerator section through the top vent.
For your convenience, the Temperature Control is
preset at the factory. The control for the refrigerator and
freezer is located in the top of the refrigerator section. It
controls the temperature in both the refrigerator and
freezer corn partments,
When you first install your refrigerator, make sure that
the Temperature Control is still preset. The
Temperature Control should be at the "mid-setting" (3),
as shown in the illustration below.
NOTE: Turning the Temperature Control to OFF stops
cooling in both the refrigerator and freezer compartments,
but does not disconnect the refrigerator from the power
supply,
Give your refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before you put food
into the refrigerator.
IMPORTANT: If you add food before the refrigerator has
cooled completely, your food may spoil. Turning the
Temperature Control to a higher (colder) than
recommended setting will not cool the compartments
any faster.
Do not block any of these vents with food packages. If
the vents are blocked, airflow will be prevented and
temperature and moisture problems may occur.
IMPORTANT: Because air circulates between both
sections, any odors formed in one section will transfer to
the other. You must thoroughly clean both sections to
eliminate odors. To prevent odor transfer and drying out of
food, wrap or cover foods tightly. (See the "Food Storage
Guide" section for details.)
11
= ,,,o,<_,+_>_+j_,;,<,=,<, ¢,,,j %1111,1%11 ,+,JI,,=I,I,II I%11,=I
I +,,J .+.J
Give the refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before you put food
into the refrigerator. The "mid-setting" (3) indicated in the
previous section should be correct for normal household
refrigerator usage. The control is set correctly when milk or
juice is as cold as you like and when ice cream is firm.
The Temperature Control functions as the thermostat for
the entire product (refrigerator and freezer sections). The
higher the number setting, the longer the compressor will
run to keep the temperature colder.
Use the settings listed in the chart below as a guide.
Always remember to wait at least 24 hours between
adjustments.
RECOMMENDED
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR section
too warm
Turn
TEMPERATURE
Control to next
• Door opened often
• Large amount of food added
higher number,
wait 24 hours,
then re-check
• Room temperature verywarm
FREEZER section too warm/ice
not made fast enough
Turn
TEMPERATURE
Control to next
• Door opened often
• Large amount of food added
higher number,
wait 24 hours,
then re-check
• Very cold room temperature
(can't cycle often enough)
• Heavy ice usage
• Air diffuser blocked by items
Move items out of
airstream
Storing Fresh Food
Wrap or store food in the refrigerator in airtight and
moisture-proof material unless otherwise noted. This
prevents food odor and taste transfer throughout the
refrigerator. For dated products, check code date to
ensure freshness.
Butter or margarine
Keep opened butter in covered dish or closed
compartment. When storing an extra supply, wrap in
freezer packaging and freeze.
Cheese
Store in the original wrapping until you are ready to use
it. Once opened, rewrap tightly in plastic wrap or
aluminum foil.
Milk
Wipe milk cartons. For best storage, place milk on
interior shelf.
Eggs
Store in original carton on interior shelf.
Fruit
Wash, let dry, and store in refrigerator in plastic bags or
crisper. Do not wash or hull berries until they are ready
to use. Sort and keep berries in original container in a
crisper, or store in a loosely closed paper bag on a
refrigerator shelf.
REFRIGERATOR section
too cold
• Control not set correctly for
your conditions
FREEZER section too cold
• Control not set correctly for
your conditions
Turn
TEMPERATURE
Control to next
lower number,
wait 24 hours,
then re-check
Turn
TEMPERATURE
control to next
lower number,
wait 24 hours,
then re-check
12
Leafy vegetables
Remove store wrapping and trim or tear off bruised and
discolored areas. Wash in cold water and drain. Place in
plastic bag or plastic container and store in crisper.
Vegetables with skins (carrots, peppers)
Place in plastic bags or plastic container and store in
crisper.
Fish
Use fresh fish and shellfish the same day as purchased.
Meat
Store most meat in original wrapping as long as it is
airtight and moisture-proof. Rewrap if necessary. See
the following chart for storage times. When storing meat
longer than the times given, freeze the meat.
Chicken ........................................................... 1-2 days
Ground beef .................................................... 1-2 days
Variety meats (liver, heart, etc.) ....................... 1-2 days
Cold cuts ......................................................... 3-5 days
Steaks/roasts .................................................. 3-5 days
Cured meats .................................................. 7-10 days
Do not use:
Bread wrappers
Non-polyethylene plastic containers
Containers without tight lids
Wax paper or wax-coated freezer wrap
Thin, semi-permeable wrap
Freezing
Your freezer will not quick-freeze any large quantity of
food. Put no more unfrozen food into the freezer than will
freeze within 24 hours (no more than 2 to 3 Ibs of food per
cubic foot [907-1,350 g per liter] of freezer space). Leave
enough space in the freezer for air to circulate around
packages. Be careful to leave enough room at the front so
the door can close tightly.
Storage times will vary according to the quality and type of
food, the type of packaging or wrap used (airtight and
moisture-proof), and the storage temperature. Ice crystals
inside a sealed package are normal. This simply means
that moisture in the food and air inside the package have
condensed, creating ice crystals.
NOTE: Allow hot foods to cool at room temperature for 30
minutes, then package and freeze. Cooling hot foods
before freezing saves energy.
Leftovers
Cover leftovers with plastic wrap or aluminum foil.
Plastic containers with tight lids can also be used.
Storing Frozen Food
NOTE: For further information about preparing food for
freezing or food storage times, check a freezer guide or
reliable cookbook.
Packaging
Successful freezing depends on the correct packaging.
When you close and seal the package you must not allow
air or moisture in or out. Ifyou do, you could have food
odor and taste transfer throughout the refrigerator, and
also dry out frozen food.
Packaging recommendations:
• Rigid plastic containers with tight-fitting lids
• Straight-sided canning/freezing jars
• Heavy-duty aluminum foil
• Plastic-coated paper
• Non-permeable plastic wraps (made from saran
film)
• Specified freezer self-sealing plastic bags
Follow package or container instructions for proper
freezing methods.
13
4. Slide shelf out the rest of the way.
REFRIGERATOR
FEATURES
F F_...... _ = • ':A,+I_,{%
i:} 0I,>- DO0
The door trim may be removed for easier cleaning.
To remove the trim:
1. Remove all items from the shelf.
2. Pull straight up on each end of the trim.
To replace the trim:
1. Locate each end of the trim piece above the trim
pocket opening.
2. Push the trim straight down until it stops.
The shelves in your refrigerator are adjustable to match
your individual storage needs.
Storing similar food items together in your refrigerator and
adjusting the shelves to fit different heights of items will
make finding the exact item you want easier. It will also
reduce the amount of time the refrigerator door is open,
and save energy.
To remove a shelf:
1. Remove items from the shelf.
I
To replace a shelf:
1. Slide back of shelf into shelf track in wall of cabinet.
2. Guide front of shelf into shelf track.
3. Slide shelf in all the way.
To remove the crisper(s):
1. Slide crisper(s) straight out to the stop.
2. Lift the front.
3. Slide out the rest of the way.
4. Replace the crisper(s) in reverse order.
Style 1
To remove the plastic cover:
1. Remove crisper(s).
2. Lift cover front and remove the cover support.
3. Lift cover up and slide out.
2. Slide shelf straight out to the stop
3. Depending on your model, lift back or front of shelf to
pass stop.
14
Loading...