Crosley CRG3140GBBA, CRG3140GBBB, CRG3140GBBC, CRG3140GBBD, CRG3140GBBE Installation Guide

INSTALLATION AND SERVICE MUST BE PERFORMED BY

AQUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

This conversion kit must be installed by a qualified service technician in accordance with the

manufacturer's instructions and all applicable codes and requirements ofthe authority having jurisdiction. Failure
to follow instructions may result in fire, explosion or production of carbon monoxide causing property damage,
personal injury or loss of life. The qualified service agency is responsible for the proper installation of this kit. The
installation is not proper and complete until the operation of the converted appliance is checked as specified in
the manufacturer's instructions supplied with this kit.

Before proceeding with the conversion, shut off the gas supply before disconnecting electrical

power to the range. Be sure both power supplies are off before installing the conversion kit. Failure to do so could
cause serious bodily injury.

Determine the combination of top burners that are featured on your range. Identify the parts you need from this kit to com-
plete the L.P. conversion. When burners are converted from Natural to L.P. the BTU ratings are as follows:

5,000 BTU* Natural Gas to 4,500 BTU* L.P. Gas
9,500 BTU* Natural Gas to 8,000 BTU* L.P Gas
12,000 BTU* Natural Gas to 10,000 BTU* L.P. Gas

Quantity Part Number Part Description

14,000 BTU* Natural Gas to 11,000 BTU* L.P.Gas
16,000 BTU* Natural Gas to 14,000 BTU* L.P. Gas

Notes

1
1

1
1
1
1

1
1
1
1
1

1
1
1
4
1

1
1
1
1
1

1
1
1

*Note: For o oeration at elevations above 2000 ft., appliance rating shall be reduced at the rate of 4 percent for each 1000 ft. above
sea level.

316037527 L.P.Conversion Kit Label
316417504

316005215
316005216
316005217
316005218

316005219
316005220
316005221
316005222
316241200

316237910
316237904
316237905
316237906
316237907

316005223
316005224
316005225
316005226
316005227

316005228
316005229
316005230

Instructions for converting range to L.P. Gas English, French & Spanish
Rating Plate - English

Rating Plate - English
Rating Plate - English
Rating Plate - English
Rating Plate - French

Rating Plate - French
Rating Plate - French
Rating Plate - French

L.P.Conversion Label
Orifice - 14,000 BTU*
Orifice - 11,000 BTU*
Orifice - 10,000 BTU*
Orifice - 8,000 BTU*

Orifice - 4,500 BTU*
Rating Plate - English

Rating Plate - French
Rating Plate - English
Rating Plate - French
Rating Plate - English
Rating Plate - French

Rating Plate - English
Rating Plate - French

English & French

4- 8k
3+1
2+1+1

1+1+1+1

4- 8k
3+1
2+1+1

1+1+1+1
English, French & Spanish

Black
Red

Green

No Color
Blue
1-11k, 2-8k, 1-4.5k
1-11k, 2-8k, 1-4.5k

1-11k + 3-8k
1-11k + 3-8k
1-14k, 1-10-k, 1-8k, 1-4.5k
1-14k, 1-10-k, 1-8k, 1-4.5k
1-14k, 1-10-k, 1-8k, 1-4.5k
1-14k, 1-10-k, 1-8k, 1-4.5k

IMPORTANT: After replacing the natural gas to LP orifices, be sure to keep the original factory installed natural
gas orifices for future range conversion back to natural gas. The factory orifices are marked with 101 for 5,000 BTU;

Tools Required for L.P. Conversion:

3/8", 1/2" and 5/8" Open End Wrench

1/8" Wide Flat Blade Screwdriver _ & 7mm Nutdriver

pin 316417504 (0407)

1

Frangais- Pages 6-10

Espa5ol - Paginas 11-15

How to Convert the Range for use with LP/
Propane Gas

1. Convert the Pressure Regulator

To access the gas regulator, remove the storage drawer or warmer
drawer. If equipped with a storage drawer, open and remove the drawer
completely. For models equipped with a storage drawer or front panel,

remove the storage or front panel and skip steps a & b below. For models
equipped with warmer drawer, follow all the instructions below to remove

the warmer drawer.
a. _!_ Electrical Shock Hazard can occur and result in

serious injury or death. Disconnect electrical power to the range
before removing the warmer drawer for servicing.

b. Locate glide lever on each side of drawer, pull up on the left glide lever

and push down on the right glide lever (See Fig. 1).
c. Pull the drawer away from the range (See Fig. 2).
d. Remove the regulator access cover if equipped. Do not remove the

Pressure Regulator or allow it to turn.
e. Remove the dust protector from the cap. Using a 5/8" wrench,

unscrew the cap from the pressure regulator. Do not remove the

spring from the regulator.
f. Turn the cap over so the hollow end faces outward. Place the solid

end of the cap into the loop end of the dust protector (See Fig. 3).
g. Replace the cap on the regulator. The letters LP should be visible on

the exposed end of the cap. Snap the dust protector over the

regulator cap.

Pull up with finger

Pressure

Front access to Regulator: Regulator

Open storage or warmer drawer, located at

or remove lower panel rear of

(on some models)

Fig. 2

Dust

Protector

Spring

Left Glide

Push down with finger

Fig. 1

Hollow End Solid End

Towards Towards

Fig. 3

Regulator Regulator

for Natural Gas for LP/Propane Gas

Natural Gas Orifice to L.P. Orfice Conversion for each
size of burner

(A locations) 5,000 BTU Natural Gas

converts to 4,500 BTU L.P. Gas

Install (blue) marked orifice .68mm for L.P.

(B locations) 9,500 BTU Natural Gas

converts to 8,000 BTU L.P. Gas

Install (no color) marked orifice .89 mm for L.P.

(D locations) 12,000 BTU Natural Gas

converts to 10,000 BTU L.P.Gas

Install (green) marked orifice .95 mm for L.P.

(E locations) 14,000 BTU Natural Gas

converts to 11,000 BTU L.P. Gas

Install (red) marked orifice 1.01 mm for L.P.

(F locations) 16,000 BTU Natural Gas

converts to 14,000 BTU L.P.Gas

Install (black) marked orifice 1.99mm for L.P.

Fig. 4