Crosley CDG4000HW1, CDG4000FW1 Owner’s Manual

AUTO DRY

__MED DRY

Normal

Pe_m Press

o o

45 75

DRYER OPERATING iNSTRUCTiONS

O Mo_eDry
0 N{_rmal

5O

No

Heat

TEMP

Low

0 LessDry
0 Damp

0

DRYNESS

0 PressSave_' 0 PressSavef
0 CydeS gnal 0 deankintFilter

O0 O0

OPTIONS Selec_ START Pause

0- Ca_cel

0 Drying
0 (oe[ D_wn

O O (olltro[ @

Before Operating Your Dryer

Read your dryer Owner's Guide. It has important
safety and warranty information. It also has many

suggestions for best drying results.

To reduce the risk of fire, electric

shock or injury to persons, read the IMPORTANT
SAFETY INSTRUCTIONS in your dryer Owner's
Guide before operating this appliance.

Operating Steps

Read "Drying Procedures" inyour Owner's Guide.
It explains these operating steps in detail.

1. Prepare items for drying.

2. Check that lint screen is clean and in place.

3. Load the dryer. If desired, add a dryer fabric
softener sheet. Close the door.

4. Select the cycle and drying temperature for each

load. To change the temperature, turn the TEMP
knob to the desired temperature.

,

A suitable dryness level and options will

automatically be displayed for each cycle. To

change the dryness level, press DRYNESS until

the desired selection is made. To select an
option, press OPTIONS until the indicator for a

desired option flashes and press Select.

Follow the same steps to delete an option. Ifa

dryness level or option isnot available for a cycle,

it will not light.

,

The changes you make will be remembered the

next time that cycle is selected. See the "Dryer
Settings Chart" for more details.

.

Press START to begin cycle.

, To pause the cycle or change settings,

press Pause/Cancel once.To resume

the cycle, press START again.

• Tostop or change the cycle, press
Pause/Cancel twice.

8. A signal will sound at the end of the cycle and
periodicallyduring Press Saverwhen the Cycle

Signal option is selected. When the cycle ends,
remove items immediately and hang or fold.

9. Clean the lint screen after every load.

Cycle Selection

For best results, follow the fabric care label

instructions on items to be dried.

Auto Dry
Auto Dry cycles take the guesswork out of drying
time. The load will automatically be dried at the
selected temperature to the desired dryness level.
The dryer senses the moisture level of the load as
it tumbles through heated air. Auto Dry cycles save
time and energy and protect fabrics.

When the load has reached the selected dryness
level, it will continue to tumble, unheated, during a
Cool Down period. This helps reduce wrinkling and
makes items easier to handle during unloading.

Drying time varies depending on size and dampness
of load, weight and fabric type. Room temperature
and humidity, type of installation and electrical
voltage or gas pressure can also affect drying time.

Towels
Select this Auto Dry cycle for towel loads.

Normal
Select this Auto Dry cycle for cotton items.

Perm Press
Select this Auto Dry cycle to dry cottons and blends

with a no-iron finish.

PN 134420600D (0604)

Cycle Selection (Con't)

Delicate
Select this Auto Dry cycle for knits and delicate

items.

Quick

Select this cycle to quickly dry a small load made
up of just a few items. It provides approximately

20 minutes of tumbling followed bya 10-minute cool
down period.

Touch Up
Select Touch Up to help remove wrinkles from clean
and dry items that were not taken from the dryer at
the end of the cycle, have been stored in crowded
closets or drawers, or unpacked from luggage

following a trip. It provides approximately 10 minutes

of tumbling followed by a 5-minute cool down
period.

Timed Dry
To manually select the drying time for any load,
turn the knob to a numbered setting. Drying times

from 15 to 90 minutes are available in 15-minute

increments. You will not be able to select a cycle
or dryness level. Timed Dry is recommended when
using the No Heat option.

Note: To change cycles, press Pause/Cancel
twice.

Temperature Selection

For best results, follow the fabric care label
instructions on items to be dried.

High is recommended for sturdy fabrics.

Medium is recommended for wrinkle free,
permanent press and lightweight fabrics.

No Heat should only be used with a Timed Dry
setting to dry items containing feathers, down, foam
rubber, plastics or rubber-like materials; to freshen
clothing, pillows or blankets; or to dust draperies.

Note: Using No Heat in any Auto Dry cycle will
result in long drying times and/or wet loads at the
end of the cycle.

Toavoid fire hazard, do not use heat

to dry items containing feathers or down, foam
rubber, plastics, or similarly textured, rubber-like
materials. Use the No Heat setting only.

Cycle Adjustments

A suitable combination of dryness level and options
will automatically be displayed for each cycle. The
settings can be changed before the cycle isstarted.
Those adjustments will automatically be
remembered each time that cycle is selected. Ifa
dryness level or option is not recommened for a
cycle, the indicator will not light. See the "Dryer
Settings Chart" for more details.

If changes are attempted after the cycle starts, the
status lights will blink and the signal will beep 3
times. The cycle must be paused before the set-
tings can be changed.

Dryness Level

Tochange the dryness level, press DRYNESS until
the desired selection is made. Select Normal for

most loads.
Occasionally a load may seem too damp or over-

dried at the end of the cycle. To increase drying
time for similar loads in the future, select More

Dry. For loads requiring less drying time, select
Less Dry.

Select Damp Dry for items you wish to partially
dry before hanging or ironing.

Note: To prevent over-drying, not every dryness
level isavailable with every cycle.

Options

To select an option, press OPTIONS until the
indicator for the desired option flashes and press
Select. If an option is not available for a cycle, the
indicator will not light. Follow the same steps to
delete an option.

The Cycle Signal will sound at the end of the cycle
and periodically during Press Saver.

Select Press Saver if the dried load might not be
removed promptly at the end of the cycle. The dry
load will continue tumbling without heat for 30
minutes to help reduce wrinkling. When the Cycle
Signal is selected, a beep will be heard periodically.
The load may be removed any time during Press

Saver.

Dryer Features

_(Control Lock)
Toavoid having someone accidentally start or stop

the dryer, press OPTIONS and Select at the same
time and hold for about 10 seconds until the

_(Control Lock) lights up. Tounlock the controls,
press and hold OPTIONS and Select for about 10

seconds.

Status Lights
The following indicators may be lighted during the
cycle:
'* Drying

,* Cool Down
o Press Saver

Clean Lint Filter

_ (Control Lock)

Low is recommended for delicate fabrics.

PN 134420600D (0604)