Crosley CAE25ESR2, CAE25ESR1, CAE18ESR1, FAM157R1A1, FAM157R1A2 Installation Guide
...
Instructions
For Heavy
Median {FAM
Please read ALL instructions be_hre installing.Two people are
recommended to install this prodaetdf a new electrical outlet
is reqaired,have the outlet installed by a qaalified electrician
be_re installing anit. See#5 in Prdiminary lnstraetions
_bllowing.
Duty {/:AS Models) and
Models) Air Conditioners
Preitiminary
Do the _bHowiog be_bre startiog to iostall aoR.See illustrations
bdow.
Check dimensions of your unit to determine model type:
Heavy duD' (FAS) Median (FAM)
Unit Height: 18.5/8" 17.5/8"
Unit Width: 26 1/. 23 1/.
Min. Window Opening: 19" 18 72"
Min. Window Width: 31" 26 1/,,
Max. Window Width: 43" 40 1/2"
SIDE RETAINER /
1°
Check window opening size =the mounting parts furnished
with this air conditioner arc made to install in a wooden
sill double-hung window.The standard parts are for
window dimensions listed aboveX)pen sash to a minimum
of i9"(483mm). (FIG. i)
2. Cheek condition of window =all wood parts of window
must be in good shape and able to firmly hold the needed
sorer s.If not, make repairs before installing uniL
FIG. 1
SASH
T
19"MIN
1/2" MIN
1
BRACKET
3_
Check your storm windows =if your storm window
*?ame does not allow the clearance required, correct by
adding a piece of wood as shown in FIG.2, or by removing
storm window while room air conditioner is being installed.
(continued)
FIG. 2
SASH
t
19" MIN
1/2" MIN i 1 1/2"MIN
STORM WINDOW FRAME OR
OTHER OBSTRUCTION
I _ ENTIRESTOOL,FASTEN
STORM WINDOW FRAME OR WITH TWO NAILS OR
OTHER OBSTRUCTION SCREWS.
P/N 66121623
4. CHECK FOR ANYTHING THAT COULD BLOCK
AIRFLOW- check area outside of window for things
such as shrubs, trees, or awnings. Inside, be sure
flu_nimre, drapes, or blinds will not stop proper air flow.
5. Check the avaiiaNe deetrkai service - power suppb_ must
be the same as that shown on the unit serial nameplate.
(See Owner's Guide fbr serial plate location. _Power cold
is 48"long. Be sure you have an outlet near.
All models have a 3-prong sel_Ace phlg to provide proper
sel_/ice and sate positive groudmg. Do not change plug m
any way. Do not use an adapter plug. If your present wall
outlet does not match your plug, call a qualified electlician
to make the needed change.
NC Avoid ISlehazad or electric
shock. Do not use m_extension cord or gm
adaptor phlg. Eb not remove _uLvprong fi_om
the power cord.
Too s Nequired
a large flat blade screwdriver
tape uleasure
adjustable wrench or pliers
pencil
Level
Socket wrenches
Phillips screwdriver
Hardware {in plastic bag)
Qty.
,_ Washer Head
Locking Screw
For window panels
3/4" Long Hex°Head Screw
2
Groundhog type wall
receptacle
./ .............................................................
circul
re o,
_, grou_
plug and current
detection device
6. Careful b, unpack air conditioner - remove all packing
material. Protect floor or carpet ti_om damage. Two
people should be used to move and install unit.
Safety Lock
@_ 1/2" Long Screw
__ 3/4" Long Flat
and locknut
Head Bolt and
Locknut
Sill Angle Bracket
locking screw %r
top angle, side
Long hex-head
retainer 5/16"
Long
4 ea.
2 ea.
10
Remove Chassis
lnstatm Top Angl÷
and Side Bracket
1. 1hill down ftont panel axt remove filter. (See FIG. !).
2. Lift ftont upwards and place to one side.
3. Locate file fimr flont screws _mdremove. These screws will
be needed to re=install the flont later. (See f'IG.2)
4. PU away flont flom cabinet sides as per photo (see FIG.3)
5. Gently lift flont offunit and place to one side (See FIG.4).
6. Remove shipping crews flom top ofumt gradalso on the side
by the base if installed.
7. Hold the cabinet wNle pulling on the base hgmdle, gradcare-
fillly lemove the unit.
8. Add two i[)_un inserts to holes in top of cabinet where
shipping screws were removed flom.
Attach tbam gasket to top angle above holes as
shown in FIG. 6.
2. Install top
gmgk grad
side retainers
to cabinet as
shown in FIG. 6.
Assemble Window
Fill÷r Panels
Place cabinet on floor, a bench, or a table.
2.
Slide 'T' section of window filler panel into side retainer
on the side of the cabinet (see Figures 7°8). Do both
sides.
FIG. 7
PLASTI( \r_TNDOV, FILLER
FRAME PANEL
9. Your unit may come wifil internal packaging.THIS
PACKAGING MUST BE P,EMOVED PRI()R T()
INSTALLING THE AIR C()NDITIONER BACK
INT() THE CABINET. (See HG. 5)..
d
[3
FIG. 8
RETASNER
TOP
VIEW
i AIR ( O)q)ITIONE_
CABE','ET
T' SECTION
SIDE
PLASTIC
FRAME
WENT)OW HOLE
FILLER
PANEL
Loading...