How it Works
Crosley
Loading...
BTF1240FS1
Installation Guide
8 pgs912.3 Kb0
Owner’s Manual
10 pgs1.22 Mb0

Crosley BTF1240FS1, FTF1240FS0, FTF1240FS1, FTF530FS1, FTF530FS2 Installation Guide

...
installation instructions
Notice d'installation
Before beginning installation, carefully read these instructions. This will simplify the installation and ensure the
washer is installed correctly and safely. Leave these instructions near the washer after installation for future reference.
NO TE: The electrical service to the washer must conform with local codes and ordinances and the latest edition of the National Electrical Code, ANSI/NFPA 70 or in Canada, CSA C22.1 Canadian Electrical Code Part 1.
Avant de commencer, life attentivement le present document. Cela simplifiera rinstallation et assurera la pose correcte et securitaire de la laveuse. Apres I'installation, laisser ce document a proximite de la laveuse pour reference
_For your safety the information in this manual must be followed to minimize the risk of fire or explosion
or to prevent property damage, personal injury or lossof life.
Do not store or use gasoline or other flammable vapors and liquid in the vicinity of this or any other appliance.
- WHAT TODO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not useany phone inyour building.
• Clear the room, building or area of all occupants.
• Immediately call your gassupplier from a neighbor_ phone. Follow the gas suppliers instructions.
• If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or the gassupplier.
_Pour votre securite, suivre lesdirectives donnees dans le present guide afin de minimiser lesrisques
d'incendie, d'explosion, de dommages materiels, de blessures et de mort.
Ne pasentreposer ni utiliser d'essence ou d'autres vapeurs ou liquides inflammables a proximite de cette secheuseou de
tout autre appareil electromenager.
- QUEFAIRES'IL YA UNE ODEUR DE GAZ N'allumer aucun appareil electrique.
Ne toucher aucun commutateur electrique; ne pas utiliser le telephone dans I'immeuble. Faire sortir tousles occupants de la piece, de I'immeuble ou de lazone avoisinante.
Appleler la comgagnie de gaz immediatement en utilisant le telephone d'un voisin. Suivre les instructions de la compagnie de gaz.
S'il est impossible dejoindre la compagnie de gaz, appeler les pompiers.
L'installation et les reparations doivent etre effectuees par un technicien qualifie, un agent de service ou la compagnie de
gaz.
Printed in U.S.A. P/N 134891600 (0706)
CONTENTS
SUBJEC T PA GE
Pre-lnstallation Requirements ................................................. 2
Electrical Requirement .......................................... 2
Grounding Requirement ........................................ 2
Water Supply Requirements .......................................... 2
Drain Requirements ................................................ 2
Location ©f Your Washer ........................................... 2
Unpacking ...................................................... 2-3
Rough-In Dimensions ............................................. 3
Installation ....................................................... 4
Replacement Parts ............................................... 4
Franqais ........................................................... 5-8
PRE-INSTALLATION REQUIREMENTS
Tools Required for Installation:
1. 1/4 in. nut driver
2. 3/8 in. socket with ratchet.
3. 3/8 in. open end wrench.
4. 7/16 in. socket with ratchet.
5. 9/16 in. open end wrench.
6. Channel-lock adjustable pliers.
7. Carpenter's level.
ELECTRICAL REQUIREMENTS
CIRCUIT- Individual, properly polarized and grounded 15 amp.
branch circuit fused with 15 amp. time delay fuse or circuit breaker. POWER SUPPLY- 2 wire, with ground, 120 volt, single phase, 60 Hz, Alternating Current. NOTE: The use of this washer with power created by gas powered generators, solar powered generators, wind powered generators or any other generator other than the local utility company is not recommended.
WATER SUPPLY REQUIREMENTS
Hot and cold water faucets MUST be installed within 42 inches (107 cm) of your washer's water inlet. The faucets MUST be 3/4 inch (1.9 cm) garden hose type so inlet hoses can be connected. Water pressure
MUST be between 10 and 120 pounds per square inch (maximum unbalance pressure, hot vs. cold, 10 psi.) Your water department can advise you of your water pressure.
DRAIN REQUIREMENTS
1,
Drain capable of eliminating 17 gals (64.3 L) per minute.
2.
A standpipe diameter of 1-1/4 in. (3.18 cm) minimum.
3.
The standpipe height above the floor should be:
Minimum height: 24 in. (61 cm) Maximum height: !)6 in. (244 cm)
96 in.
(244 cm)
Max.
24 in.
(61 cm)
Min.
NOTE:
Drain hose attached to the washer carl reach a 58 in. (147 cm) high standpipe. For higher standpipe use hose P/N 131461201,
available from an authorized parts distributor. If drain is less than 24 in. (61 cm), install a siphon break kit, available at your
local hardware store.
LOCATION OF YOUR WASHER
OUTLET RECEPTACLE - Properly grounded 3-prong receptacle to
be located so the power supply cord is accessible when the washer is in an installed position. NOTE: GFI (Ground Fault Interrupter)
receptacle is not required.
GROUNDING REQUIREMENTS
Improper connection of the equipment grounding
conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly
grounded.
1. The washer MUST be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electrical shock by
a path of least resistance for electrical current.
2. Since your washer is equipped with a power supply cord having an equipment-grounding conductor and a grounding plug, the plug MUST be plugged into an appropriate, copper wired
receptacle that is properly installed and grounded in accordance with all local codes and ordinances or in the absence of local
codes, with the National Electrical Codes, ANSI/NFPA 70 (latest edition). If in doubt, call a licensed electrician. DO NOTcut off
or alter the grounding prong on the power supply cord. In situations where a two-slot receptacle is present, it is the owner's
responsibility to have a licensed electrician replace it with a properly grounded three prong grounding type receptacle.
DO NOT INSTALL YOUR WASHER:
1. In an area exposed to dripping water or outside weather conditions. The ambient temperature should never be below 60 degrees F (15.6 degrees C) for proper washer operation.
2. In an area where it will come in contact with curtains or drapes.
3. In an area (garage or garage-type building) where gasoline of other flammables are kept or stored (including automobiles).
4. On carpet. Floor MUSTbe solid with a maximum slope of 1/2 in. per foot (1.27 crrl per 30.5 cm). To ensure vibration or movement does not occur, reinforcement of the floor may be necessary.
IMPORTANT MINIMUM INSTALLATION CLEARANCES When installed in alcove or closet:
Sides, Rear = 0 in. (0 cm)
Top = 0 in. (0 cm) Front Console Model
Top = 15 in. (38.1 cm) Rear Console Model
When installed in closet: Front = 1 in. (2.54 cm) Closet door ventilation required:
2 Iouvered openings each 60 in 2 (387 cm2), 3 in. (7.6 cm) from top and bottom of door.
UNPACKING
1. Cut the shipping carton along the (Jotted line along the base of the unit.
2. While in the carton carefully lay the washer on its back side.
3. Remove the styrofoam base.
4. Carefully return the washer to an upright position and remove
the carton.
2
5. Carefully move the washer to within 4 feet (122cm) of the final location.
6. Remove the following from the back side of the washer:
3 bolt 3 yellow plastic spacers,
2 or 3 metal "P" clamps.
BOLT
SPACER
©
"P" CLAMP
9. Remove the large styrofoam block located under the drum. Lift up on the drum, tilt the base of the foam block inwards toward the
rear of the washer until free, then pull it out.
10. Remove and discard the yellow ribbon and label from the front of
the washer.
11. From the rear of the washer, carefully pull out the power supply
cordthrough the hole in the backsheet.
12. Replace the service panel and screws.
NOTE: If the washer is to be transported at a later date, the shipping support hardware must be reinstalled to prevent shipping damage.
Retain the hardware in the plastic baq provided,
7. Remove the service panel from the front of the washer.
8. Remove the 4 nuts and 6 large washers that attach the 2 yellow shipping braces to the drum and the base. Lift up on the drum and remove the braces (a yellow ribbon surrounds the items to
be removed). These braces must be removed to allow the power
supply cord to be released from the shipping ring.
ROUGH-IN DIMENSIONS
17
(43.2)
inch (cm) Adjustable Legs
24 3A
(62.9)
Power
Cord 331/2
(85)
SIDE
26%
(67.9) _"
2_
(7.3)
o
@
17
24 3/4
(62.9)
Power
Cord
331/2
(85)
inch (cm) Adjustable Legs
263/4
"_ (67.9) _"
27/8
.... (7.3)
361(91.5)
Water
Under
Counter
34%
(87.9)
BACK
UNDER COUNTER INSTALLATION
If an under counter" installation is desired, the washer MUST have a top sheet kit installed, P/N 131445600. Kit is available from an authorized parts distributor. _Custorn sized countertop is required.
Inlets
31%
(80.3)
l
3
36
(91.5)
Under
Counter
34%
(8i'9)
Watel
Inlets
31%
1803:
, I
Loading...
+ 5 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use