Page 1
Page 2
The exclamation point
within an equilateral
triangle is intended to
alert user to the
presence of important
operating and
maintenance (servicing)
instruction in the
literature accompanying
the appliance.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
The lighting flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert user to
the presence of uninsulated
"dangerous voltage" within
the product's enclosure
that may be of sufficient
magnitude to constitute
risk of electric shock
to persons.
CAUTION: TO REDUCE
THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE
COVER (OR BACK). NO
USER - SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Ventilation not being impeded.
Do not exposed to dripping or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
Specification
FREQUENCY : FM 88 -108 MHz
AM 530 - 1700 KHz
USB Port 2.0 : Full Speed 512MB - 4GB
(Support FAT16, FAT32)
POWER SOURCE : AC Adaptor AC120V/DC 9V 800mA
ANTENNA : External antenna for FM
Built-in ferrite bar for AM
POWER CONSUMPTION : 15W
SPEAKER SIZE : 2" x 3" Dynamic type x 2
SPEAKER OHM : 4 ohm
SPEAKER WATT : 3-5W
POWER OUTPUT : 1.2W x 2
REPLACEMENT NEEDLE : NP1
*DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
USB Specification:
Interface
- USB 2.0 Full speed, HOST (USB HUB is not supported) Corresponding Flash memory
- Compatible with MPEG Audio 1, 2, 2.5
- Compatible with Layer 1, 2, 3
- Compatible with Bit rate: 128 320 Kbps
- Subfolder nest : 8 levels
- Number of track / titles max 999
- Support ID3 tag V2.0
12
LIMITED MANUFACTURERS WARRANTY
Crosley Radio, Inc. warrants the product to be free from defects in material and
workmanship under normal use for a period of one year from the original date of
purchase. This warranty is not transferable. If the product is determined to be defective
during the warranty period, the unit will be repaired or replaced at Crosley Radios sole
discretion. This warranty covers manufacturing defects and normal consumer use and
does NOT cover damage or failure as a result of abuse, accident, alterations, misuse,
neglect, abnormal wear and tear, inadequate maintenance, commercial or unreasonable
use, damage caused by power surges, mishandling, accident, acts of God or attempted
repair by an unauthorized service agent. Also not covered are cosmetic damages,
cords and antennas.
Should this product fail to function in a satisfactory manner, it is best to first return it
to the store or retailer where it was originally purchased. If additional service is still
needed, the original purchaser must FIRST contact our offices to obtain an RA (Return
Authorization) Number.
TO OBTAIN AN RA NUMBER
CALL: 1.888.CROSLEY
(1.888.276.7539)
Send the unit prepaid to the address below in the original packaging (or reasonable
substitute to prevent damage). Clearly mark your RA number on the outside packaging
and include the original sales receipt (or a copy) indicating date of purchase, amount
paid, and place of purchase. You must also include your full name, shipping address
and daytime contact number. Please include a check or money order in the amount
of $19.95, made payable to Crosley Radio, to cover handling and return shipping
charges. Returned products will not be shipped to PO Boxes. Crosley Radio will not
be responsible for delays or unprocessed claims resulting from a purchasers failure
to provide any or all of the necessary information.
CROSLEY RADIO
ATTN: RETURNS DEPT
2001 PRODUCTION DRIVE
Louisville, KY 40299
For additional support: Crosley Radio Consumer Service Department
24 hours a day / 7 days a week
Telephone: 1.888.CROSLEY (1.888.276.7539)
There are no express warranties except as listed above.
The purchasers bill of sale is the only proof of warranty entitlement.
This warranty gives the purchaser specified legal rights in addition to any rights which
may vary from state to state.
In accordance with the Moss-Magnuson Warranty Act of July 10, 1975, this is termed
a limited warranty which in no way compromises Crosley Radios high standards of
quality and workmanship.
Page 3
1 You can connect external components to your
unit by using the Auxiliary Input.
2 Plug Auxiliary cable
(not supplied) into the LINE
IN JACK on the back of your unit.
3 Switch the LINE IN SWITCH to the ON position.
4 Plug the other end of the Auxililary cable into the
output jack on your desired external component.
5 Check the volume level of your external
component.
6 See operators manual for correct operation of
the external component.
NOTE: When not using the Auxiliary Input, make
sure the LINE IN SWITCH is in the OFF position.
10
1 Connect headphones to the Headphone Jack
2 Adjust volume to the desired listening level.
NOTE: When using headphones, the sound to
the unit speakers will be cut off.
NOTE: Headphones not included with unit.
1 You can connect your radio to different sources
using the auxiliary output.
2 Plug Auxiliary cables (not supplied) into the
LINE OUT JACK.
3 Connect the other end of the Auxiliary cables
into the input on your desired component.
4 See the owners' manual for the component for
correction operation.
NOTE: The Auxiliary Output is a passive signal level
output only and will not power speakers.
Getting Started
Unpacking................................. 4
Power Source........................... 4
Control Locators....................... 5,6
Basic Operation
Turntable Operation.................. 7
Radio Operation....................... 7
USB/SD Operation.................. 8
Recording
PHONO to USB/SD................. 8
MP3 copying............................ 9
Audio/Connections
Auxiliary Output ...................... 10
Auxiliary Input.......................... 10
Headphone Jack operation..... 10
General
Troubleshooting Guide.......... 11
Warranty.............................. 12
About This Manual
Welcome Table of Contents
Auxiliary Output
Audio / Connections
Auxiliary Input
Thank you for purchasing the Crosley Tech Series
Turntable (CR6007A). Before operating this unit,
please read this manual thoroughly and retain it for
future reference.
Instructions in this manual describe the control
functions of the CR6007A.
Included in the package:
Tech Series Turntable
Remote Control
AC Power Adaptor
45 RPM Adaptor
Headphone Jack Operation
The sound from all speakers is cut off.
Headphone Jack
Page 4
1 Slide the FUNCTION Switch to SD/USB mode.
2 Switch the unit ON by turning the VOLUME
ON/OFF KNOB to the on Position.
3 Turn the VOLUME control in mid-range position.
4 Plug-in USB mass storage device. READ is
displayed as the system scans the contents of
USB device.
5
Before starting playback, press and hold
STOP / for approximately 2 seconds to
switch between SD/USB. Release the button when
USB is shown on the display.
6 Track no. 1 of the first folder will be displayed
after the contents of the SD Card have been
USB
MP3
USB
USB
SPEAKER
VOLUME
ON/OFF
KNOB
EARPHONE JACK
RADIO\
SD/USB\
PHONO
SWITCH
SD CARD
DIAL SCALE
AM\FM\
FM.ST
SWITCH
USB PORT
TUNING KNOB
SPEAKER
X-BASS
ON/OFF
BACKWARD SKIP
FORWARD SKIP
REC/ERASE
POWER
INDICATOR
SENSOR
LCD DISPLAY
FM.ST INDICATOR
PROGRAM
STOP/
SD/USB
PLAY/
PAUSE
REPEAT
1 Slide THE FUNCTION Switch to SD/USB mode.
2 Switch the unit ON by turning the VOLUME
ON/OFF KNOB to the on Position.
3 Turn the VOLUME control in mid-range position.
4 Insert SD-Card into the card slot. READ is
displayed as the system scans the contents of
SD card.
5
Track no. 1 of the first folder will be displayed
after the contents of the SD Card have been read.
Press
PLAY/PAUSE / to start playback.
6 Press the
FORWARD SKIP/
/
BACKWARD
SKIP /
once or repeatedly until the desired
track number appears in display.
7 Press STOP /
to stop playback.
Note: If your music is separated into multiple folders
on your SD Card, this unit will only show the actual
MP3 files and will NOT show the different folders in
which the files are stored.
7 Press the
FORWARD SKIP
/ /
BACKWARD
SKIP
/ once or repeatedly until the desired
track number appears in display.
8 Press STOP /
to stop playback.
Note: If your music is separated into multiple folders
on your USB Flash Drives this unit will only show
the actual MP3 files and will NOT show the different
folders in which the files are stored.
Notes:
1. USB connector does not support connection with
USB extension.
2. This unit is not designed for communication with
computer directly.
3.
All USB Flash Drives and SD Cards may not be
compatible with this unit.
IMPORTANT:
Do not disconnect the USB device SD card during
USB/SD mode, as this may damage the external
device or its files. Please power off first or press
another Mode before safely disconnecting the USB
device /SD card.
This unit allows you to convert your records into MP3
format onto either USB Flash Drive or an SD Card.To
convert your records, follow the steps below.
1 Slide the FUNCTION button to PHONO mode.
2 Start playback of the record at the point you want
to start recording. (See Turntable Operation on
Page 7 for more information on playing your
record).
3 Press
REC/ERASE / to start recording.
4. REC will show on the display and TO will be
shown briefly.
5 The media that you are recording to (either USB
or SD), will begin flashing on the display once
recording begins.
6 Press
STOP / to stop recording.
58
CARD
CARD
read. Press PLAY/PAUSE / to start playback.
Control Locators
AC ADAPTOR
JACK
EXTERNAL
FM ANTENNA
LINE OUT
JACK
LINE IN JACK
LINE IN SWITCH
LOCK HINGE
LID PIVOT POINT
LID PIVOT POINT
Basic Operation
SD-Card Operation
USB Operation
Phono to USB/SD
Page 5
Troubleshooting
11
There is no Power
1 Make sure radio is plugged in correctly.
2 The unit is not turned on: Rotate the VOLUME
ON/OFF KNOB from the OFF position past the
click to turn on the unit.
There is no Sound
1 Check the volume level by turning the VOLUME
ON/OFF KNOB.
2 Make sure headphones are not connected to
the unit.
3 Check the position of the FUNCTION SWITCH.
Turntable will not work
1 Make sure the FUNCTION SWITCH is set to
phono.
2 Try moving the tone arm to the right until you
hear a click.
3 Make sure the protective needle cover is
removed.
IMPORTANT SAFETY INSTRUCTION
PLEASE READ CAREFULLY ALL THE FOLLOWING IMPORTANT SAFEGUARDS
THAT ARE APPLICABLE TO YOUR EQUIPMENT
1. Read Instructions - All the safety and operating instructions should be read before the product is operated.
2. Retain instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on the product and in the operating Instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.Use
a damp cloth for cleaning.
6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
8. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it from overheating, and these openings must not be blocked
or covered, The openings should never be blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in a built - in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
10. Power Sources - This product should be operated only from the type of power source indicated on the marking label,
if you are not sure of the type of power supply to your home. Consult your product dealer or local power company.For
products intended to operate from battery power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet try reversing the plug, If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power - Cord Protection - Power - supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the product.
13. Lightning - For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the product due to lightning and power - line surges.
14. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
15. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
16. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short - out parts that could result in a fire or electric shock. Never spill liquid of any kind
on the product.
17. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions;
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance - this indicates a need for service.
19. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, or other hazards.
20. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
21. Wall or ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat - The product should be situated away from heat sources such as radiators. Heat registers, stoves, or other
products (including amplifiers) that produce heat.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the users authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio TV technician for help.
AC
Polarized Plug
General
Page 6
1 Remove packing materials from unit.
Note: Save all packing materials.
2 Remove plastic bag covering radio.
3 Remove AC Adaptor from Packing.
4 Open lid and remove styrofoam shipping material
from turntable.
5 Remove black tie-wrap from under the tone arm.
6 Remove white protective needle cover by gently
pulling towards the front of the unit.
7 Install the top lid onto the unit.
SETUP
1 Untie the wire on the AC Adaptor.
2 Untie the FM antenna and allow it to hang down
in a straight line for optimum FM reception. If
you have trouble tuning a FM station, move the
external FM antenna for best reception. Do not
connect FM antenna to outside antenna.
1 Plug the AC Adaptor into appropriate wall outlet.
2 Plug the small end of the adaptor into the AC
ADAPTOR JACK on the back of the unit.
CD
P
4 9
1 Flip the LID LOCK HINGE towards the back of
the unit.
2 Position LID over the turntable and press the lid
onto the LOCK HINGE as shown below.
3 As you press the lid into place, align the PIVOT
PINS on the LID with the LID PIVOT POINTS as
shown below.
4 Press the LID all the way in until the PIVOT PINS
snap into the LID PIVOT POINTS and the LOCK
HINGE clicks into place.
1 To copy one individual song from either USB or
SD, press
REC/ERASE / while the desired
song is playing to start Mp3 copying from USB
to SD card or SD card to USB. Playback will be
stopped and system will scan the contents of
USB/SD card and create a folder to store the
MP3 track.
2 REC " will show on the display.
3 Message COPY 01 will be displayed.
4 The icon for the device that you are recording to,
USB or CARD, will begin flashing. The display
will show 01 as MP3 copying starts, the recording
process will stop as it reaches 100
5 Original MP3 source, SD or USB will begin playing
from the beginning once copying is complete.
6 You can also copy all MP3 songs from USB to
SD card or SD card to USB. While in SD/USB
mode and playback is stopped, press
REC/ERASE / . The unit will copy all songs
from the USB to SD or SD to USB.
This units allows you to delete individual songs from
your SD Card or USB Flash Drive. To erase a
particular song, that song must be playing.
1 While in SD/USB mode, select the song you
would like to delete and begin playback.
2 Once the song is playing, press and hold the
REC/ERASE / button for approximately
2 seconds. The song will stop playing and will
be deleted.
3 The display will briefly show delete"
Note: You can only erase one song at a time. You
cannot erase the entire SD Card or USB Drive at
one time.
2 Press the
FORWARD SKIP
/ /
BACKWARD
SKIP/
once or repeatedly until the desired track
number appears in the display.
3
Press PROGRAM / to confirm. The display
will show the stored track number and the next
available position.
4 Repeat step 2-3 to select and store all desired
tracks. FULL is displayed if you attempt to program
more than 20 tracks
5 Press PLAY/PAUSE /
to play the program.
6 To erase the programmed playback, press the
STOP / button twice. Turning the unit off or
switching to a different function will also erase
the programming.
1 Press REPEAT / on remote at Play mode.
2 Default Play Mode function is OFF.
3 REPEAT 1 / REPEAT FOLDER / REPEAT ALL .
THREE kinds of Play Mode can be chosen in MP3
type.
Press the X-BASS ON/OFF to ON or OFF the
X-BASS effect(Adjust the volume level to mid to
maximize the X-BASS effect).
CD
P
P
CD
You may program up to 20 tracks from your SD Card
or USB Drive to play in the order you
choose.
1 While playback is stopped, press the PROGRAM
/ button to start programming. P and P0-01
will begin flashing on the display.
Getting Started
Unpacking
Power Source
Basic Operation
Deleting MP3 Tracks
MP3 Copying
Programming Tracks
Lid Installation
Play Mode
X-BASS
click
Page 7
SPINDLE
TURNTABLE
ADAPTER FOR 45 RPM RECORDS
TONE ARM
TONE
ARM
REST
SPEED CONTROL SWITCH
6 7
Turn the unit on by rotating the VOLUME ON/OFF
KNOB located on the front panel to the ON position
1 Set the FUNCTION SWITCH to PHONO mode.
2 Set the SPEED CONTROL SWITCH to the
desired speed (33 1/3, 45 or 78 rpm). Place your
record onto the turntable.
3 Move the TONE ARM slightly to the right side
until you hear a click sound to activate the
turntable.
4 Move the TONE ARM by hand over the record
to the point you want the record to start. Adjust
the VOLUME ON/OFF KNOB to your desired
listening level.
5 At the end of the record, the TONE ARM will stop
automatically. You must return the TONE ARM
to the arm rest by hand.
This adaptor allows you to play 45 RPM records.
1 Place the 45 RPM adaptor over the spindle.
2 Gently place your 45 RPM record onto the
turntable.
3 Follow the steps under turntable operation to
play your record.
1 Set the FUNCTION SWITCH to RADIO mode.
2 Set the AM / FM / FM.ST SWITCH to the
desired Band.
3 Select the desired radio station by rotating
TUNING KNOB .
4 Adjust the
VOLUME ON/OFF KNOB to the
desired sound level.
Antenna: for FM reception, the unit is provided with
a FM WIRE ANTENNA , move the wire until the
reception is clear and with no interferences. For AM
reception, the unit is provided with a directional
build-in ferrite antenna. Rotate the set to find the
position in which the best reception is obtained. Do
not connect the EXTERNAL FM ANTENNA to any
outside antenna.
Turntable Operation Radio Operation
Accessory: Adapter for 45 rpm
Antenna
Control Locators
Basic Operation
PLAY/PAUSE
STOP/SD/USB
BACKWARD SKIP
0-9
REC/ERASE
REPEAT
FORWARD SKIP
PROGRAM
PROG
798
3
1 2
4 5
6
0
REPEAT
REC/
ERASE
SD/USB
Loading...