Crosley 2212430 User Manual

®

T OP-MOUNT

REFRIGERATOR

Table of Contents..........2

2212430

www .cr osley.com

T ABLE OF CONTENTS

REFRIGERATOR SAFETY.......................................................... 3

INSTALLING YOUR REFRIGERATOR..........................................4

Unpacking Your Refrigerator.......................................................4

Space Requirements....................................................................4

Electrical Requirements...............................................................5

Connecting the Refrigerator to a Water Source..........................5

Base Grille....................................................................................6

Refrigerator Doors: Removing,

Reversing (optional) and Replacing.............................................7

Door Closing and Alignment........................................................8

Understanding Sounds You May Hear........................................9

USING YOUR REFRIGERATOR....................................................9

Ensuring Proper Air Circulation....................................................9

Setting the Control(s) .................................................................10

Adjusting Control Settings.........................................................10

REFRIGERATOR FEATURES......................................................11

Refrigerator Shelves...................................................................11

Lateral Adjustable Shelf.............................................................11

Meat Drawer and Cover.............................................................12

Chilled Meat Drawer...................................................................12

Crisper and Crisper Cover.........................................................12

Crisper Humidity Control ...........................................................13

Utility or Egg Bin.........................................................................13

Wine or Can/Bottle Rack ...........................................................13

FREEZER FEATURES..................................................................13

Ice Maker....................................................................................13

Freezer Shelf ..............................................................................14

Adjustable Half-width Freezer Shelf ..........................................14

Pull-out Freezer Floor.................................................................15

DOOR FEATURES........................................................................15

Door Rails...................................................................................15

Door Bins....................................................................................15

Can Rack....................................................................................15

Adjustable Utility Compartment & Tray.....................................15

Flip-up Door Shelf......................................................................16

CARING FOR YOUR REFRIGERATOR.......................................16

Cleaning Your Refrigerator.........................................................16

Changing the Light Bulbs...........................................................16

Power Interruptions....................................................................17

Vacation and Moving Care.........................................................17

TROUBLESHOOTING..................................................................17

ASSISTANCE OR SERVICE.........................................................19

WARRANTY.............................................................................. 20

2

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or

“WARNING.” These words mean:

You can be killed or seriously injured if you don't
immediately follow instructions.

You can be killed or seriously injured if you don't
follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can

WARNING:

precautions:

■

■

■

■

■

■

■

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

To redu ce t he ris k of fire, electric shock, or injury when using your refrigerato r, follo w these basic

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extensio n cord.
Disco n n e c t po wer before ser v ic i n g .

Replace all panels before operating.
Remove doors from your old refriger a tor.

■

Use nonflammable cleaner.

■

Keep flammable materials and vap or s , such as
gasoline, aw ay from refr iger ato r.

■

Use two or mo re peop le to mov e and install
refrigerator.

■

Disconnect power before installing ice maker (on
ice maker kit ready models only).

■

Use a sturdy glass when dispensing ice or water
(on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of

Your Old Refrigerator

W ARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or
brain damage.

IMPORTANT : Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
– even if they will sit for “just a few days.” If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.

Before you throw away your old refrigerator or freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

3

INSTALLING YOUR

REFRIGERATOR

Unpacking Y our Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install
refrigerator.

Failure to do so can result in back or other injury.

Remove shelves from the shipping position (shelves are
shipped upside down):

Grasp the front of the upper shelf with one hand and use the

1.

other hand to remove packing material from the shelf area.
Lower the front of the upper shelf until shelf hooks can be

2.

removed from the shelf supports and pull the shelf forward.
Flip the shelf over and insert the rear shelf hooks into the

3.

shelf supports. Tilt th e front of shelf up until rear shelf hooks
drop into the shelf supports.

Lower the front of the shelf and check to make sure that it is

4.

securely in position.

Removing packaging materials

■ Remove tape and any labels from your refrigerator before

using (except the model and serial number label).
To remove any remaining tape or glue, rub the area briskly

with your thumb. Tape or glue residue can also be easily
removed by rubbing a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and
dry .

■ Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see “Refrigerator Safety” section.

■ On some models, shelves, bins, door shelf rails, and other

feature parts may be packaged in the Int erior FeaturePak.
Follow the instructions contained in the package for proper
assembly.

IMPORTANT :

■ Depending on your model, do not remove any permanent

instruction labels inside your refrigerator or the Tech Sheet
that is fastened behind the base grille.

■ Depending on your model, do not remove the white

Styrofoam inse rt that is located behi nd the control panel on
the ceiling of the refrigerator. The insert is part of the
refrigerator and not part of the packing materi al. If the insert
is removed, ice may migrate down from the freezer and cause
icicles to form.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor.
Always pull the refrigerator straight out when moving it.
Do not wiggle or “walk” the refrigerator when trying to move
it, as floor damage could occur.

Cleaning before use

After you remove all of the package materials, clean the inside of
your refrigerator before using it. See the cleaning instructions in
the “Caring for your Refrigerator” section.

Important information to know about glass shelves
and covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter
into many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when re­moving them to avoid impact from dropping.

Space Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as
gasoline, away from refrigerator.

Failure to do so can result in death, explosion,
or fire.

■ To ensure proper ventilation for your refrigerator , allow for a .5

in. (1.25 cm) space on each side and at the top.

.5" (1.25 cm)

2" (5.08 cm)

■ If your refrigerator has an ice maker, make sure you leave

some extra space at the back for the water line connections.
The refrigerator can be flush against the back wall if you do
not have an ice maker installed.

■ If you are installing your refrigerator next to a fixed wall, leave

2 in. (5.08 cm) minimum on each side (depending on your
model) to allow for the door to swing open.

Do not install the refrigerator near an oven, radiator, or

NOTE:

other heat source, nor in a location where the temperature will fall
below 55°F (13°C) .

4

Electrical Requirements

W ARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection:

Recommended gr oun ding met hod

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be tur ned off by a switch. Do not use an
extension cord.

Before performing any type of installation, cleaning, or

NOTE:

removing a light bulb, turn the control, (Thermostat, Refrigerator
or Freezer Control depending on the model) to OFF and then
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source
and reset the control (Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.

Tools required:

■ Standard screwdriver

■ ⁷⁄₁₆ in. and ¹⁄₂ in. open-end wrenches or two adjustable

wrenches

■ ¹⁄₄ in. nut driver

■ ¹⁄₄ in. drill bit

■ Hand drill or electric drill (properly grounded)

Your refrigerator dealer has a kit available with a

NOTE:

¹⁄₄ in. (6.35 mm) saddle-type shut-off valve, a union, and copper
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes. Do not use a piercing­type or ³⁄₁₆ in. (4.76 mm) saddle valve which reduces water flow
and clogs more easily.

Cold water supply

The ice maker water valve contai ns a flow washer which is used
as a water pressure regulator. The ice maker needs to be
connected to a cold water line with water pressure between 30
and 120 psi. If a problem occurs, ca ll your utility company.

Connecting to water line:

Unplug refrigerator or disconnect power.

1.

Turn OFF main water supply. Turn ON nearest faucet long

2.

enough to clear line of water.
Locate a ½ in. to 1¹⁄₄ in. (12.7 mm to 3.18 cm) vertical COLD

3.

water pipe near the refrigerator.

Horizontal pipe will work, but the following procedure

NOTE:

must be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.

To determine the length of copper tubing you will need,

4.

measure from connection on lower left rear of refrigerator to
water pipe. Add 7 ft. (2.1 m) to allow for moving refrigerator
for cleaning. Use ¹⁄₄ in. (6.35 mm) O.D. (outside diameter)
copper tubing. Be sure both ends of copper tubing are cut
square.

Using a gr ounded drill, drill a ¹⁄₄ in. hole in the cold water pipe

5.

you have selected.

Connecting the Refrigerator

to a W at er Source

Read all directions carefully before you begin.
IMPORTANT :

■ If operating the refrigerator before installing the water

connection, turn ice maker to th e OFF position to prevent
operation without water.

■ All installations must be in accordance with local plumbing

code requirements.

■ Use copper tubing and check for leaks.

■ Install copper tubing on ly in areas where temperatures will

remain above freezing.

■ It may take up to 24 hours for your ice maker to begin

producing ice.

1. Cold Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut-Off Valve

7. Packing Nut

5

6. Fasten shut-off valve to cold water pipe with pipe clamp. Be
sure outlet end is solidly in the ¹⁄₄ in. drilled hole in the water
pipe and that washer is under the pipe clamp. Tighten
packing nut. Tighten the pipe clamp screws carefully and
evenly so washer makes a watertight seal. Do not overtighten
or you may crush th e c op pe r tubing, especially if soft (co iled )
copper tubing is used. Now you are ready to connect the
copper tubing.

7. Slip compression sleeve and compression nut on copper
tubing as show n. Inse rt end of tu bing into o utle t en d sq uar el y
as far as it will go. Screw compression nut onto outlet end
with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and
turn ON main water supply and flush out tubing until water is
clear. Turn OFF shut-off valve on the water pipe. Coil copper
tubing.

Connecting to refrigerator:

1. Attach the coppe r tube to the va lve inlet us ing a compr ess ion

nut and sleeve as shown . Tighten the compression nut. Do
not overtighten. Use the tube clamp on the back of the
refrigerator to secure the tubing to the refrigerator as shown.
This will help prevent damage to the tubing when the
refrigerator is pushed back against the wall. Move to step 2.

2. Turn shut-off valve ON. Check for leaks. Tighten any
connections (including connections at the valve) or nuts that
leak.

Base Grille

To remove the base grille:

1. Open the refrigerator door.

2. Grasp the grille with both hands.

3. Lift up and tilt the bottom of the grille toward you.
NOTE: Do not remove the Tech Sheet that is fastened behind the

grille.

To replace the base grille:

1. Open the refrigerator door.

2. Place upper clips in openings in the metal panel.

3. Roll the grille down toward the refrigerator until it snaps into

place.

1. Tube Clamp

2. Copper Tubing

3. Compression Nut

4. Valve Inlet

3. The ice maker is equipped with a built-in water strainer. If
local water conditions require periodic cleanin g or a well is
your source of water supply, a second water strainer should
be installed in the ¹⁄₄ in. (6.35 mm) water line. Obtain a water
strainer from your nearest appliance dealer. Install at either
tube connection.

4. Plug in refrigerator or reconnect power.

6

Refrigerator Doors: Removing, Reversing (optional) and Replacing

TOOLS NEEDED: ⁵⁄₁₆ in. hex-head socket wrench, No. 2 Phillips screwdriver, flat-head screwdriver, ⁵⁄₁₆ in. open-end wrench, flat 2 in.
putty knife.

IMPORTANT: Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food and any
adjustable door or utility bins from doors.

Door Removal &

Replacement

Base Grille

Top Hinge

1. Top Hinge Cover

5

/

2. " Hex-Head Hinge Screws

16

3. Top Hinge

Center Hinge

Door Swing Reversal (optional)

2

1

1

1. Cabinet Hinge Hole Plugs

2

1

1

1. Door Hinge Hole Plug

3

1.

2
3

1

1. Flat-Head Handle Screws

2. Freezer Handle

4

1

1-2

5

/

" Hex-Head Hinge

16

Screws

1-1

1

1

1. Center Hinge

5

/

2. " Hex-Head Hinge Screws

16

Bottom Hinge

1. Bottom Hinge

5

/

2. " Hex-Head Hinge Screws

16

1

7

1. Door Handle Sealing Screws

2

Front View

1. Door Stop Screw

1

Side View

2

2. Door Stop

1

2

6-1

1

1. Door Handle
Screw Cover

5

1. Door Handle
Seal Screw Front

6-2

1. Flat-Head

Handle Screw

1

2

3

6-3

2. Refrigerator Handle

3. Handle Screw

7

Door and hinge removal

⁵⁄₁₆

” Hex Head Hinge Screw

Unplug refrigerator or disconnect power.

1.

Open refrigerator door and remove base grille from the

2.

bottom front of the refrigerator (see Base Grille graphi c).
Close the refrigerator door and keep both doors closed until

3.

you are ready to lift them free from the cabinet.

Provide additional support f or the doors while the

NOTE:

hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.

Remove the parts for the top hinge as shown in Top Hinge

4.

graphic.
Lift the freezer door free from the cabinet.

5.

Remove the parts for the center hinge as shown in the Center

6.

Hinge graphic.
Lift the refrigerator door free from the cabinet.

7.

Remove the parts for the bottom hing e as shown in the

8.

Bottom Hinge graphic.

IMPORTANT: If you want to reverse your doors so that they
open in the opposite direction, follow these steps. If you are
not reversing the doors, see “Door and hinge replacement”.

Door reversal (optional)

Door Stop Screw Door Hinge Hole Plug

Door Handle Sealing Screw Cabinet Hinge Hole Plug

Flat-Head Handle Screw Door Handle Screw Cover

Door Handle Seal Screw Front Round-Head Handle Screw

Cabinet

Remove

1.

move them to opposite side (see Graphic 1-1).
Remove cabinet hinge hole plugs from cabinet top and move

2.

them to opposite side hinge holes as shown (see Graphic 1-

2).

Freezer door

Remove freezer handle assembly as shown . Keep all parts

1.

together (see Graphic 2).
Remove door hinge hole plug. Move to opposite side as

2.

shown (see Graphic 3).
Remove door handle sealing screws. Move to opposite side

3.

of freezer door as shown (see Graphic 4).
Remove door stop. Move to opposite side of freezer door as

4.

shown (see Graphic 5).
Position freezer handle on opposite side of freezer door.

5.

Assemble handles on door as shown (see Graphic 2).
Tighten all screws. Set aside door until hinges and

6.

refrigerator compartment door are in place.

in. hex head hinge screws from handle side and

⁵⁄₁₆

Refrigerator door

Remove refrigerator handle bottom trim. For

1.

the handle screw cover (see Graphic 6-1). For
trim down as shown (see Graphic 6-2).

Remove refrigerator handle assembly as shown. Keep all

2.

parts together (see Graphic 6-3 ).
Remove door hinge hole plug from refrigerator door. Move to

3.

opposite side hinge h ole as shown (see Graphic 3).
Remove door handle sealing screws. Move to opposite side

4.

of refrigerator door as shown (see Graphic 4).
Remove door handle seal screw front. Move to opposite side

5.

of refrigerator door as shown (see Graphic 7).
Remove door stop. Move to opposite side of refrigerator door

6.

as shown (see Graphic 5).
Position refrigerator handle on opposite side of the

7.

refrigerator door as shown (see Graphic 6-3). Drive top two
screws in handle first. Align lower portion of handle and drive
bottom screw.

Align refrigerator bottom trim. For

8.

handle screw cover (see Graphic 6-1). For
into place (see Graphic 6 -2).

Tighten all screws. Set aside refrigerator door until bottom

9.

hinge is instal led on product.

Style 1,

Style 1,

replace the door

Style 2,

Style 2,

slide trim

remove

slide

Door and hinge replacement

Graphic may be reversed if door swing is reversed.

NOTE:

Replace the parts for the bottom hinge as shown. Tighten

1.

screws.
Replace the refrigerator door.

2.

Provide additional support for the doors while the

NOTE:

hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.

Assemble the parts for the center hinge as shown and tighten

3.

all screws (see Center Hinge graphic).
Replace the freezer door.

4.

Assemble the parts of the top hinge as shown (see Top Hinge

5.

graphic). Do not tighten screws completely.
Line up the doors so that the bot tom of the freezer door

6.

aligns evenly with the top of the refrigerator door. Tighten all
screws.

Final Steps

Check all holes to make sure that hole plugs and screws are

1.

in place. Reinstall top hinge cover (see Top Hinge graphic).
Replace the base grille (see Base Grille graphic).

2.

Plug in refrigerator or reconnect power.

3.

Reset the controls (see “Setting the Controls” section).

4.

Return all removable door parts to doors and food to product.

5.

Door Closing and Alignment

Door Closing

Your refrig erator ha s two fron t adjus table r olle rs – one on th e right
and one on the left. If your refrigerator seems unsteady or you
want the doors to close easier, adjust the refrigerator's tilt using
the instructions below:

Plug into a grounded 3 prong outlet.

1.

Move the refrigerator into its fi nal position.

2.

Remove the base grille (see “Base Grille” earlier in this

3.

section). The two leveling screws are part of the front roller
assemblies which are at the base of the refrigerator on either
side.

8

4. Use a screwdriver to adjust the leveling screws. Turn the
leveling scr e w to the right to raise that side of the ref r ige r a t o r
or turn the leveling screw to the left to lower that side. It may
take several turns of the leveling screws to adjust the tilt of
the refrigerator.

NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws and
rollers. This makes it easier to adjust the screws.

5. Open both doors again and check to make sure that they
close as easily as you like. If not, tilt the refrigerator slightly
more to the r ear by turning both l eveling sc rew s to the righ t. It
may take several more turns, and you should turn both
leveling screws the same amount.

6. Replace the base grille.

Door Alignment

If the space between your doors looks uneven, you can adjust it
using the instructio n s be low:

1. Pry off the top hinge cover.

2. Loosen the top hinge screws using a ⁵⁄₁₆ in. socket or wrench.

3. Have someone hold the door in place or put a spacer

between the doors while you tighten the top hinge screws.

4. Replace the top hinge cov e r.

■ Your refrigerator is designed to run more effici ently to keep

your food items at the desired temperature. The high
efficiency compressor may cause your new refrigerator to run
longer than your old one, and you may hear a pulsating or
high-pitched sound.

■ Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

■ You may hear the evaporator fan motor circulating the air

through the refrigerator and freezer compartments.

■ As each cycle ends, you may hear a gu rgling sound due to

the refrigerant flowing in your refrigerator.

■ Contraction and expansion of the inside walls may cause a

popping noise.

■ You may hear air being forced over the condenser by the

condenser fan.

■ You may hear water running into the drain pan during the

defrost cycle.

USING YOUR

REFRIGERATOR

Ensuring Proper Air Circulation

In order to ensure proper temperatures, you need to permit
airflow between the refrigerator and freezer sections. As shown in
the illustration, cool air enters through the bottom of the freezer
section and moves up. Most of the air then flows through the
freezer section vents and recirculates under the freezer floor. The
rest of the air enters the refrigerator section through the top vent.

Understanding Sounds You May Hear

Your new refrigerator may make sounds that your old one didn’t
make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces, like the floor, walls, and cabinets, can make the sounds
seem louder than they actually are. The following describes the
kinds of sounds and what may be making them.

■ If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to fill the ice
maker for each cycle.

■ The defrost timer will click when the automatic defrost cycle

begins and ends. Also, the Thermostat Control (or
Refrigerator Control depending on the model) will click when
cycling on and off.

■ Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

Do not block any of these vents with food packages. If the
vents are blocked, airflow will be prevented and temperature and
moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent
odor transfer and drying out of food, wrap or cover foods tightly.

9

Setting the Control(s)

For your convenience, the refrigerator controls are preset at
the factory. Controls for the refrigerator and freezer are located

in the top of the refrigerator section.

When you first install your refrigerator, make sure that the
control(s) are still preset. The control(s) should be at the
“mid-settings” as shown for each style of control.

Mid-setting “3”

Mid-setting “3”

WARMER

1

2

REFRIGERATOR

3

RECOMMENDED SETTING

4
5

COLDER

WARMER

FREEZER

RECOMMENDED SETTING

COLDER

1
2

3

4
5

Adjusting Control Settings

Give the refrigerator time t o co o l do w n co m p le tely before adding
food. It is best to wait 24 hours before you put food into the
refrigerator. The “mid-settings” indicated in the previous section
should be correct for normal household refrigerator usage. The
controls are set correctly when milk or juice is as cold as you like
and when ice cream is firm.

For models with two controls:

The Refrigerator Control functions as the thermostat for the entire
product (refrigerator and freezer sections). The higher the number
setting, the longer the compressor will run to keep the
temperature colder. The Freezer Control adjusts the cold air flow
from the freezer to the refrigerator.

If you need to adjust temperatures in the refrigerator or freezer,
start by adjusting the refrigerator first. Wait 24 hours after the
refrigerator adjustment to check the freezer temperature. If it is
too warm or too cold, then adjust the Freezer Control as well.

For models with a single control:

The Temperature Control functions as the thermostat for the
entire product (refrigerator and freezer sections). The higher t he
number setting, the longer the compressor will run to keep the
temperature colder.

Use the settings listed in the chart below as a guide. Always

remember to wait at least 24 hours between adjustments.

Mid-setting “4”

REFRIGERATOR

4

FREEZER

4

NOTE: To turn your refrige rato r off, turn the refrige rato r con tr o l to
the word OFF or until the word OFF appears, as shown below.
Your product will not cool when the refrigerator control is set to
OFF.

REFRIGERATOR

OFF

WARMER

1
2

REFRIGERATOR

3

RECOMMENDED SETTING

4
5

COLDER

Give your refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before you put food into
the refrigerator.

IMPORTANT: If you add food before the refrigerator has cooled
completely, your food may spoil. Turning the Refrigerator or

Freezer Control(s) to a higher (colder) than recommended
setting will not cool the compartments any faster.

On models with t wo controls, the Free z er Co n trol functions as an
airflow director . Setting “1” will direct more of the cold air into the
refrigerator section, while se tting “5” (or “7” depending on your
model) will d ir ect mor e of the cold air into th e f re eze r se ction . Th e
cold air flows from the freezer compartment through the top vent
into your fre sh food s ect io n ( s ee d ia gra m in the "En su ring Proper
Air Circulation" section). On models with one control, the airflow
does not require adjustment.

CONDITION/REASON:

REFRIGERATOR section
too warm

■ Door opened often

■ Large amount of food added

■ Room temperature very warm

■ Blocked air stream

FREEZER section too warm/ice not
made fast enough

■ Door opened often

■ Large amount of food added

■ Very cold room temper a ture (can ’t

cycle often enough)

■ Heavy ice usage

■ Blocked air stream

RECOMMENDED
ADJUSTMENT:

Turn
REFRIGERATOR
Control or
TEMPERATURE
Control to next
higher number, wait
24 hours, then re­check

Move items out of
air stream

Turn FREEZER
Control or
TEMPERATURE
Control to next
higher number, wait
24 hours, then re­check

Move items out of
air stream

10

CONDITION/REASON:

REFRIGERATOR section
too cold

■ Controls not set correctly for your

conditions

■ Blocked air stream

FREEZER section too cold

■ Controls not set correctly for your

conditions

RECOMMENDED
ADJUSTMENT:

Turn
REFRIGERATOR
Control or
TEMPERATURE
Control to next
lower number, wait
24 hours, then re­check

Move items out of
air stream

Turn FREEZER
Control or
TEMPERATURE
Control to next
lower number, wait
24 hours, then re­check

To remove and replace a shelf in a metal frame:

Pull the shelf forwa rd to the stop.

1.

Tilt the front of the shelf up and lift it slightly as you pull the

2.

shelf from the frame.
Replace the shelf by guiding it back into the slots on the

3.

frame and pushing the shelf in past the stop.

Shelves a nd Shel f Fram es

To remove and replace a shelf/frame:

Remove the shel f/fr ame b y til ting it up at the fr on t and l ifti ng i t

1.

out of the shelf supports.
Replace the shelf/frame by guiding the rear shelf hooks into

2.

the shelf suppo rts . Ti lt the front of the shelf up until rear shelf
hooks drop into the shelf supports.

Lower the front of the shelf and check to make sure that the

3.

shelf is securely in position.

■ Blocked air stream

Move items out of
air stream

REFRIGERATOR FEATURES

Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word “Accessory.” Not all accessories will fit all models.
If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in t he "Assistance or
Service" section.

Important information to know about glass shelves
and covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter
into many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when re­moving them to avoid impact from dropping.

Refrigerator Shelves

The shelves in your refrigerat or are adjustable to meet your
individual storage need s. Your model may have glass or wire
shelves.

Storing similar food items together in your refrigerator and
adjusting the shelves to fit different heights of items will make
finding the exact item you want easier. It will also reduc e the
amount of time the refrigerator door is open, and save energy.

Slide-out Shelves (on some models)

■ To slide out shelf, carefully pul l front of shelf toward you.

■ To slide in shelf, push shelf in until it stops.

Lateral Adjustable Shelf

(on some models)

To slide the shelf from side to side:

Lift up on the front of shelf and slide to the desired location.

1.

Lower shelf to the level position.

2.

You do not have to remove small items from the shelf

NOTE:

before moving it from side to side. You may need to remove
larger items.

To remove the shelf:

The shelf is heavy and must be removed using both

NOTE:

hands.

Hold the back of the shelf with one hand.

1.

Lift the front of the shelf with the other hand to a 45° angle

2.

and lower it slightly t o rele ase it fr om th e upper chan nel of the
track. Pull the shelf straight out.

11

To remove and replace the shelf track:

LOW

HIGH

1. Remove the shelf track by lifting both sides of the track
slightly and pulling the track straight out.

2. Replace the track by guiding the track hooks into the shelf
support slots on the back wall.

NOTE: Make sure that both sets of track hooks are in the
slots and that the slots are parallel with each other.

3. Push the track back and do wn securely into the shelf
supports.

To replace the shelf:
NOTE: Make sure that both of the rear shelf slides are securely in

the track before letting go of the shelf. The lateral shelf may be
difficult to install if the track is placed too close to the refrigerator
ceiling. Reposition the track on a lower rung until the shelf can be
tilted enough to easily slide into the track.

1. Hold the shelf at the front and tip the front at a 45° angle to
the track.

2. Insert both of the rear shelf slides into the upper channel of
the track, and lower the front of the shelf into place.

Meat Drawer and Cover

(on some models)

To remove and replace the meat drawer (all styles):

1. Remove the meat drawer by sliding it out to the stop. Lift the

front of meat drawer with one hand while supporting the
bottom of drawer with other hand. Slide drawer out the rest of
the way.

2. Replace the meat drawer by guiding it into the meat cover
supports and pushing it in until it stops.

To remove and replace the meat drawer cover (Style 1 glass):

1. Remove the meat drawer. Remove the cover by tilting up the

front of the cover and lifting at the back. Pull the cover
straight out.

2. Replace the cover by guiding the rear hooks into the shelf
supports. Tilt the cover up at the front until the rear hooks
drop into the slots.

3. Lower the front of the cover to a level position and replace the
meat drawer.

Chilled Meat Drawer

(on some models)

To adjust the meat drawer temperature:

■ Slide the meat drawer temperature control forward to make

the meat drawer less cold.

■ Slide the meat drawer temperature control backward to make

the meat drawer colder.

COLDER

COLD

Meat stor age gui de

Store most meat in original wrapping as long as it is airtight and
moisture-proof. Rewrap if necessary. See the following chart for
storage times. When storing meat longer than the times given,
freeze the meat.

Fresh fish or shellfish..................use same day as purchased

Chicken.....................................................................1-2 days

Ground beef..............................................................1-2 days

Variety meats (liver, heart, etc.)..................................1-2 days

Cold cuts...................................................................3-5 days

Steaks/roasts............................................................3-5 days

Cured meats............................................................7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers wi th tight lids.

Crisper and Crisper Cover

(on some models - Accessory)

To remove and replace the crisper(s):

1. Slide crisper(s) straight out to the stop. Lift the front of the

crisper(s) and slide out the rest of the way.

2. Replace the crisper(s) by sliding back in full y past the drawer
stop.

To remove and replace the meat drawer cover (Style 2
plastic):

1. Remove the meat drawer. Tilt the cover up at the front and

pull it forward and out.

2. Replace the meat drawer cover by fitting the notches and rear
edge of the cover over rear and center crossbars on the shelf.

3. Lower cover into place and replace the meat drawer.

12

To remove the crisper(s) cover:

1. Remove crisper(s).

2. Holding the glass insert firmly with one hand, press up in

center of glass insert until it rises above the plastic frame.
Carefully, slide the glass insert forward to remove.

3. Lift the cover frame up and remove it.

To replace crisper(s) cover:
NOTE: Before reinstalling the cover, make sure the

U-shaped re in forcement bar is reinsta lle d in th e front edge of the
crisper cover.

1. Fit back of cover frame into supports on side walls of the
refrigerator and lower the front of the cover frame into place.

2. Slide rear of glass insert into cover frame and lower front into
place.

Crisper Humidity Control

(on some models)

You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and
HIGH.

■ LOW (open) lets moist air out of the crisper for best storage

of fruits and vegetables with skins.
Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or h ull berri es until they ar e r ead y to use.
Sort and keep berries in original container in crisper, or store
in a loosely closed paper bag on a refrigerator shelf.

Vegetables with skins: Place in plastic bags or plastic
container and store in crisper.

■ HIGH (closed) keeps moist air in the crisper for best storage

of fresh, leafy vegetables.
Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place i n plastic bag or
plastic container and store in crisper.

Humidity control location:

■ Humidity Control on crisper drawer (Style 1 - on left)

■ Humidity Control on crisper cover (Style 2 - on right)

Wine or Can/Bottle Rack

(on some models - Accessory)

To remove and replace the wine rack (left) or can/bottle rack
(right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the

wall of the refrigerator.

FREEZER FEATURES

Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word “Accessory.” Not all accessories will fit all models.
If you are inte r e sted in pu r cha sin g one of th e ac ces sori es , pl eas e
call the toll-free number on the cover or in the "Assistance or
Service" section.

Ice Maker

(on some models - Accessory)

There are two styles of ice makers:

■ Normal (Style 1 - on left)

■ Maximum Ice (Style 2 - on right)

Utility or Egg Bin

(on some models -Accessory)

Remove the cover and place the eggs in the egg tray. If you
prefer , you can remove the egg tray and place the entire carton of
eggs in the bin. Replace the cover.

NOTE: Eggs should be stored in a covered container. If your
model does not have an egg bin or covered utility bin, store
eggs in their original container on an interior shelf.

MAX

NORMAL

To turn the ice maker on:

The on/off switch for the ice maker is a wire shut-off arm located
on the side of the ice maker. To tur n the ice maker on, simply
lower the wire shut-off arm.

NOTE: The ice maker will not make ice until the freezer is cold
enough. Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced .

13

To turn the ice maker off:

■ Automatic turn off: As ice is made, the ice cubes will fill the

ice storage bin, and the ice cubes will raise the wire shut-off
arm to the OFF (arm up) position.

■ Manual turn off: Lift the wi re shut-off arm to the OFF (arm up)

position and listen for the click to make sure the ice maker
will not continue to operate.

To increase ice production rate:

■ Maximum Ice Production (on some models): In maximum ice

production, the ice maker should produce approximat ely 16
to 20 batches of ice in a 24-hour period. If your refrigerator
has the maximum ice production feature, push the switch to
MAX.

■ Normal Ice Production: In normal ice production mode, the

ice maker should produce approximately 8 to 12 batches of
ice in a 24-hour period. If ice is not being made fast enough,
turn the Freezer Control toward a higher (colder) number in
half number steps. (For example, if the control is at 3, move it
to between 3 and 4.) Wait 24 hours and, if necessary,
gradually turn the Freezer Control to the hi ghest setting,
waiting 24 hours between each increase.

REMEMBER:

■ Allow 24 hours to produce the first batch of ice.

■ Discard the first three batches of ice produced to avoid

impurities that may be flushed out of the system.

■ The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

■ Avoid connecting the ice maker to a softene d water supply.

Water softener chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoid e d, make sure the water softener is
operating properly and is well maintained.

■ It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

■ Do not force the wire shut-off arm up or down.

■ Do not store anything on top of the ice maker or in the ice

storage bin.

Freezer Shelf

(on some models)

To remove the shelf:

1. Lift entire shelf slightly.

2. Move shelf all the way to one side.

3. Tilt other side up and out of shelf supports.

4. Pull shelf up and out

To replace the shelf:

1. Tilt the shelf and insert into freezer compartment.

2. Insert one end of the shelf all the way into the center of the

shelf supports.

3. Lower other end of sh elf and insert into the shelf supports.

4. Lower shelf into place.

NOTE: The shelf should lower slightly and lock into place. If the

shelf does not appear stable, make sure both ends of the shelf
are inserte d int o th e sh el f supp o r ts .

Frozen food storage guide

Storage times will vary according to the quality and type of food,
the type of packaging or wrap used (should be airtight and
moisture-proof), and the storage temperature. Seal the package
or container securely to prevent taste and odor transfer
throughout the product. Ice cryst a ls inside a sealed package are
normal. This simply means that moisture in the food and air
inside the package have condensed, creating ice crystals.

Put no more unfrozen food into the freezer than will freeze within
24 hours (no more than 2-3 lb of food per cubic foot [907-1,350 g
per L] of freezer space). Leave enough space in the freezer for air
to circulate around packages. Be careful to leave enough room
for the door to close tightly.

NOTE: For more information on preparing food for freezing,
check a freezer guide or reliable cookbook

Adjustable Half-width

Freezer Shelf

(on some models)

To remove and replace the shelf:

1. Remove the shelf by lifting the shelf up and pulling straight

out.

2. Replace the shelf over the supports and lower it into place.

14

Pull-out Freezer Floor

(on some models)

To remove and replace the freezer floor:

1. Lift both back “fences” up and out.

2. Remove the freezer floor by pulling it out about 1 in. (25.40

mm) with one hand around the air tower section (center back)
and one hand at center front.

3. Lift up floor at rear until hooks release from cabinet and pull
the floor out the rest of the way.

4. Replace the freezer floor by sliding the floor straight in until
the hooks drop into place at rear of cabinet.

5. Replace “fences” by aligning pins with socket in the floor , and
pushing down until they snap into place.

DOOR FEATURES

Door Bins

(on some models)

To remove and replace the bins:

1. Remove the bin by lifting it up and pulling it straight out.

2. Replac e th e bi n by sliding it in above the de sir e d su ppor t and

pushing it down until it stops.

Can Rack

(on some models - Accessory)

To remove and replace the rack:

1. Remove the rack by lifting it up and pullin g straight out.

2. Replace the rack by holding it above the desired support and

pushing the rack back and down until it stops.

Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word “Accessory.” Not all accessories will fit all models.
If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in t he "Assistance or
Service" section.

Door Rails

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To remove and replace the rails:

1. Remove the rails by pushing in slightly on the front of the

bracket while pulling out on the inside tab. Repeat these
steps for the other end of the rail.

2. Replace the ra ils by al igning th e ends of the b racket s with the
buttons on the sides of the door liner. Firmly snap bracket
and rail assembly onto the tabs above the shelf as shown.

Drop-in Door Rails

To remove and replace the rails:

1. Remove the rails by pu lling stra ight up on ea ch en d of th e rai l.

2. Replace the rails by sliding the shelf rail into the slots on the

door and pushing the rail straight down until it stops.

Adjustable Utility

Compartme nt & T ray

(on some models)

The utility compartment and tray slide from one side to the other
for more flexible storage. The tray fits on either side of the utility
compartment or partially underneath it. Try moving it to different
positions to find the option that works best for you.

To install the utility compartment and tray:

1. Insert the front of the utility tray into the slot on the back of

the shelf rail. Lower the back of the tray into position.

2. Place the front of the utility compartment on top of the shelf
rail. Lower the back of the compartment onto the ribs on the
refrigerator door.

15

To adjust the utility compartment or tray:

1. Lift the front slightly and slide to desired position.

2. Lower front to lock into place.

Flip-up Door Shelf

(on some models)

The shelf bottom flips up so you can stor e taller ite ms in th e doo r
shelf below. When in the down position, the shelf is strong
enough to hold up to 10 pounds (4.5 kg).

CARING FOR YOUR

REFRIGERATOR

Cleaning Y our Refrigerator

■ Do not use paper towels, scouring pads, or other harsh

cleaning tools. These can scratch or damage mat erials.

■ To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs to 1 qt. [26
g to .95 L] of water).

4. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or hars h cleane rs. Dry th or oughly wi th a s oft
cloth.

For additional protection against damage to painted metal
exteriors, apply appliance wax (or auto paste wax) with a
clean, soft cloth. Do not wax plastic parts.

5. Clean the condenser coils regularly. Coils may need to be
cleaned as often as every other month. This may help save
energy.

Style 1 - Condenser coils behind base grille:

■ Remove the base grille (see the “Base Grille” section).

■ Use a vacuum with an extended attachment to clean the

condenser coils when they are dusty or dirty.

■ Replace the base grille when finished.

Style 2 - Condenser coils in back of the refrigerator:

■ Pull refrigerator out away from the wall (see the

“Unpacking Your Refrigerator” section).

■ Vacuum coils when they are dusty or dirty.

■ Roll refrigerator back into place. Make sure to leave 1 in.

(2.5 cm) between the cabinet back and the wall.

■ Check to see if the refrigerator is level.

6. Plug in refrigerator or reconnect power.

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion,
or fire.

Both the refrig e ra tor an d freezer sections defrost auto ma ti c ally.
However, clean both sections about once a month to prevent
odors from building up. Wipe up spills immediately.

To clean your refriger ator :

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.

■ Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior
and door liners or gaskets.

Changing the Light Bulbs

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with one of the same size, shape, and wattage.

To change the refrigerator light:

1. Unplug refrigerator or disconnect power.

2. Reach behind the Control Panel and unscrew the bulb.

3. Replace the b ul b with an a pplia nce b ulb of th e sa me wat tage .

4. Plug in refrigerator or reconnect power.

1

WARMER

ALLOW 24 HOURS BETWEEN ADJUSTMENTSALLOW 24 HOURS BETWEEN ADJUSTMENTS

RECOMMENDED SETTINGRECOMMENDED SETTING

2

FREEZER

3

3

4
5

COOLER

WARMER

1
2

REFRIGERATOR

3

3

RECOMMENDED SETTINGRECOMMENDED SETTING

4

COOLER

5

To change freezer light:
(on some models)

1. Unplug refrigerator or disconnect power.

2. Reach behind light shield to remove bulb.

3. Replace bulb with a 40-watt appliance bulb.

4. Plug in refrigerator or reconnect power.

16

Power Interruptions

If the electricity in your house goes off, call the power company
and ask how long it will be off.

1. If the power will be out for 24 hours or les s, keep both
refrigerator doors closed to help food stay cold and frozen.

2. If the power will be out for more than 24 hours:
a) Remove all frozen food and store it in a frozen food

locker.

OR

b) Place 2 lbs. (907 g) of dry ice in the freezer for every cubic

foot (28 L) of freezer space. This will keep the food frozen
for two to four days.

OR

c) If neither a food locker n o r dry ice is available, consume

or can perishable food at once.

REMEMBER: A fu ll fr eez er s tays co ld l onge r th an a part iall y fi lled
one. A freezer full of meat stays cold longer than a freezer full of
baked goods. If you see that food contains ice crystals, it may be
refrozen, although the quality and flavor may be affected. If the
condition of the food is poor, dispose of it.

V acation and Moving Care

V acations

If you choose to leave the refrigerator on while you’re away,

use these steps to prepare your refrigerator before you leave.

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

■ Raise wire shut-off arm to OFF (up) position or move the

switch to the OFF (right) setting.

■ Shut off water supply to the ice maker.

3. Empty the ice bin.

If you choose to turn the refrigerator off before you leave,

follow these steps.

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■ T urn off the water supply to the ice maker at least one day

ahead of time.

■ When the last load of ice drops, raise the wire shut-off

arm to the OFF (up) position or move the switch to the
OFF (right) setting.

3. Depending on your model, turn the Thermostat Control or
Refrigerator Control to OFF. See the “Setting the Controls”
section.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and
mold from building up.

Moving

When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

■ T urn off the water supply to the ice maker at least one day

ahead of time.

■ Disconnect the water line from the back of the

refrigerator.

■ When the last load of ice drops, raise the wire shut-off

arm to the OFF (up) position or move the switch to the
OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen food
in dry ice.

3. Empty the ice bin.

4. Depending on your model, turn the Thermostat Control or

Refrigerator Control to OFF. See the “Setting the Controls”
section.

5. Unplug the refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Ta ke ou t al l r e mo va b le par ts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

9. D epending on the model, raise the front of the refrigerator so
it rolls m o r e e a si ly OR s crew in the leveling legs s o th ey d on't
scrape the floor. See the “Door Closing” or “Leveling Your
Refrigerator” section.

10. Tape the doors shut and the power cord to the refrigerator
cabinet.

When you get to your new home, put everything back
and refer to the “Installing Your Refrigerator” section for
preparation instructions. Also, if your refrigerator has an
automatic ice maker, remember to reconnect the water supply to
the refrigerator.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the
cost of an unnecessary service call.

Your refrigerator will not operate

■ Is the power supply cord unplugged?

Plug into a grounded 3 prong outlet.

■ Has a household fuse or circuit breaker tripped?

Replace the fuse or reset the circuit.

■ Is the Refrigerator Control turned to the OFF position?

Refer to the “Setting the Control(s)” section.

■ Is the refrigerator defrosting?

Recheck to see if the refrigerator is operatin g in 30 minutes.
Your refrigerator will regularly run an automatic defrost cycle.

The lights do not work

■ Is the power supply cord unplugged?

Plug into a grounded 3 prong outlet.

■ Is a light bulb loose in the socket?

Turn the refrigerator control to OFF. Disconnect the
refrigerator from the electrical supply. Gently remove the bulb
and reinsert. Then reconnect the refrigerator to the electrical
supply and reset the refrigerator control.

■ Has a light bulb burned out?

Replace with an appliance bulb of the same wattage, size,
and shape. See the “Changing the Light Bulb(s)” section.

There is water in the defrost drain pan

■ Is the refrigerator defrosting?

The water will evaporate. It is normal for water to drip into the
defrost pan.

■ Is it more humid than normal?

Expect that the water in the defrost pan will take longer to
evaporate. This is normal when it is hot or humid.

17

The motor seems to run too much

The ice maker is producing too little ice

■

Is the room temperature hotter than normal?

Expect the motor to run longer under warm conditions. At
normal room temperatures, expect your motor to run about
40% to 80% of the time. Under warmer conditions, expect it
to run even more of the time.

■

Has a large amount of food just been added to the
refrigerator?

Adding a large amount of food warms the refrigerator. It is
normal for the motor to run longer in order to cool the
refrigerator back down. See the “Refrigerator Features”
section.

■

Are the doors opened often?

Expect the motor to run longer when this occurs. In order to
conserve energy, try to get everything you need out of the
refrigerator at once, keep food organized so it is easy to find,
and close the door as soon as the food is removed.

■

Is the control set correctly for the surrounding
conditions?

Refer to the “Setting the Control(s)” section.

■

Are the doors closed completely?

Push the doors firm ly shut. If they wil l not shut all the wa y , see
“The doors will not close completely” later in this section.

■

Are the condenser coils dirty?

This prevents air transfer and makes the motor work harder.
Clean the condenser coils. Refe r to the “Cleaning Your
Refrigerator” section.

Your new refrigerator will run longer than your old one due

NOTE:

to its high efficiency motor.

The refrigerator seems to make too much noise

■

The sounds may be normal for your refrigerators.

Refer to the “Understanding Soun ds You May Hear” section.

The ice maker is not producing ice

■

Is the freezer temperature cold enough to produce ice?

Wait 24 hours after hook-up for ice production. See the
“Setting the Control(s)” section.

■

Is the wire shut-off arm in the OFF (arm up) position?

Lower the wire shut-off arm to the ON (arm down) position.
See the “Ice Maker Operation” section.

■

Is the water line shut-off valve to the refrigerator turned
on?

Turn on the water valve. See the “Connecting the Refrigerator
to a Water Source” section.

■

Is an ice cube jammed in the ejector arm?

Remove the ice from the ejector arm with a plastic utensil.
Refer to the “Ice Maker Operation” s ection.

■

Does the ice maker mold have water in it or has no ice
been produced?

Check to see if your refrigerator has been connected to your
home water supply and the supply shut-off valve is turned on.
Refer to the “Connecting the Refrigerator to a Water Source”
section.

If not due to any of the above, there may be a problem

NOTE:

with the water line. Call for service.

■

Has the ice maker just been installed?

Wait 72 hours for full ice production to begin. Once your
refrigerator is cooled down, the ice maker should begin
producing 70-120 cubes every 24 hours.

■

Has a large amount of ice just been removed?

Allow 24 hours for ice maker to produce more ice.

■

Is the control set correctly?

Refer to the “Setting the Control(s)” section.

■

Is the water shut-off valve turned completely on?

Turn valve on fully. Refer to the “Connecting the Refrigerator
to a Water Source” section.

■

Is there a water filter installed on the refrigerator? This
filter may be clogged or installed incorrectly.

First, check the filter installation instructions to ensure that
the filter was installed correctly and is not clogged. If
installation or clogging is not a problem, call a qualified
person or a technician.

Off-ta st e or odor in th e ice

■

Are the plumbing connections new, causing discolored or
off-flavored ice?

Discard the first few batches of ice.

■

Have the ice cubes been stored for too long?

Throw old ice away and make a new supply.

■

Has food in the refrigerator been wrapped properly?

Refer to the “Refrigerator Features” section.

■

Do the freezer and ice bin need to be cleaned?

See the “Cleaning Your Refrigerator” section.

■

Does the water contain minerals (such as sulfur)?

A filter may need to be installed to remove the minerals.

The divide r betw een th e two com part ments i s warm

The warmth is pr ob ably due to norma l ope ratio n of the autom atic
exterior moisture control.

Temperatur e is too warm

■

Are the air vents blocked in either compartment? This
prevents the movement of cold air from the freezer to the
refrigerator.

Remove any objects from in front of the air vents. Refer to
“Ensuring Proper Air Circulation” for the location of air vents.

■

Are the door(s) opened often?

Be aware that the refrigerator will warm when this occurs. In
order to keep the refrigerator cool, try to get everything you
need out of the refrigerator at once, keep food organized so it
is easy to find, and close the door as soon as the food is
removed.

■

Has a large amount of food just been added to the
refrigerator or freezer?

Adding a large amount of food warms the refrigerator. It can
take several hours for the refrigerator to return to the normal
temperature.

■

Is the control set correctly for the surrounding
conditions?

Refer to the “Setting the Control(s)” section.

18

There is interior moisture build-up

■

Are the air vents blocked in the refrigerator?

Remove any objects from in front of the air vents. Refer to
“Ensuring Proper Air Circulation” for the location of air vents .

■

Is the door opened often?

To avoid humidity build-up, try to get ever ythin g you need ou t
of the refrigerator at once, keep food organized so it is easy
to find, and close the door as soon as the food is removed.
(When the door is opened, humidity from the room air enters
the refrigerator . The more often the door is opened, the faster
humidity builds up, especially when the room itself is very
humid.)

■

Is the room humid?

It is normal for moisture to build up inside the refrigerator
when the room air is humid.

■

Is the food packaged correctly?

Check that all food is securely wrapped. If necessary,
repackage food according to the guidelines in th e
“Refrigerator Features” section. Wipe off damp food
containers before placing in the refrigerator.

■

Is the control set correctly for the surrounding
conditions?

Refer to the “Setting the Control(s)” section.

■

Was a self-defrost cycle completed?

It is normal for droplets to form on the back wall after the
refrigerator self-defrosts.

The doors are difficult to open

■

Are the gaskets dirty or sticky?

Clean gaskets and the surface that they touch. Rub a thin
coat of paraffin wax on the gaskets following cleaning.

The doors will not close completely

■

Are food packages blocking the door open?

Rearrange containers so that they fit more tightly and take up
less space.

■

Is the ice bin out of position?

Push the ice bin in all the way.

■

Are the crisper cover, pans, shelves, bins, or baskets out
of position?

Put the crispe r co ver a nd a ll pa ns, sh elve s, bi ns, a nd ba sket s
back into their correct positions. See the “Refrigerator
Features” section for more information.

■

Are the gaskets sticking?

Clean gaskets and the surface that they touch. Rub a thin
coat of paraffin wax on the gaskets following cleaning.

■

Does the refrigerator wobble or seem unstable?

Level the refrigerator. Refer to the “Door Closing and
Alignment” section.

■

Were the doors removed during product installation and
not properly replaced?

Remove and replace the doors according to the “Refrigerator
Doors: Removing, Reversing (optional) and Replacing”
section, or call a qualified service technician.

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still nee d help, follow the instructions below.

When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to bett er respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you
only use factory specified replacement parts. Factory specified
replacement parts will fit right and work right because they are
made with the same precision used to build every new
CROSLEY

To locate factory specified replacement parts in your area, call
our Customer Interaction Center telephone number or your
nearest designated service center.

Call the Whirlpool Consumer Assistance Center
toll free:

Our consultants provide assistance with:

■ Features and specifications on our full line of appliances.

■ Installation information.

■ Use and mainte nance procedur e s.

■ Accessory and repair part s sales.

■ Specialized customer assis tance (Spanish speaking, hearing

■ Referrals to local dealers, repair parts distributors, and

For further assistance

If you need further assistance, you can write to Crosley with any
questions or concerns at:

Please include a daytime phone number in your correspondence.

®

appliance.

In the U.S.A.

1-800-253-1301.

impaired, limited vision, etc.).

service companies. Whirlpool designated service technicians
are trained to fulfill the product warranty and provide after­warranty service, anywhere in the United States.

To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.

Crosley Distribution Center
c/o Correspondence Dept.
675 North Main Street
Winston-Salem, NC 27102-2 111

19

CROSLEY® REFRIGERATOR W ARRANTY

ONE-YEAR FULL WARRANTY ON REFRIGERATOR

For one year from the date of purchase, when this refrigerator is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation will pay for factory specified replacement parts and repair labor costs to correct
defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

FIVE-YEAR FULL WARRANTY ON SEALED REFRIGERATION SYSTEM

For five years from the date of purchase, when this refrigerator is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation will pay for factory specified replacement parts and repair labor costs to correct
defects in materials or workmanship in the sealed refrigeration system. These parts are: compressor, evaporator, con denser, dryer, and
connecting tubing. Service must be provided by a Whirlpool designated service company.

Whirlpool Corporation will not pay for:

Service calls to correct the installation of your refrigerator, to instruct you how to use your refrigerator, to re place house fuses or

1.

correct house wiring or plumbing, or to repl ace light bulbs.
Repairs when your refrigerator is used in other than normal, single-family household use.

2.

Pickup and delivery. Your refrigerator is designed to be repaired in th e home.

3.

Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God, or use of products not approved

4.

by Whirlpool Corporation.

Any food loss due to product failure.

5.

Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

6.

Replacement parts and repair labor costs for units operated outside the United States.

7.

WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIA L DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you spec ific legal rights, and you may also have other rights which vary from state to state.

Outside the 50 Un ited St ates, th is warr ant y do es no t app ly. Contact your au t horized Cr o sle y deal er to deter mine if
another warranty applies.

Whirlpool Corporation is responsible for providing any in-warranty service covered in this warranty. If you need service, first see the
“Troubleshooting” section of this book. After checking “Troubleshooting”, additional help can be found by checking the “Assistance or
Service” section or by calling the Whirlpool Consumer Assistance Center, 1-800-253-1301 (toll free) from anywhere in the U.S.A. or
writing Crosley Distribution Center, c/o Correspondence Dept., 675 N. Main St., Winston-Salem, NC 27102-2111.

Keep this book and your sales slip together for future
reference. You must provide proof of purchase or
installation date for in-warranty service.

Write down the following information about your refrigerator to
better help you obtain assistance or service if you ever need it.
You will nee d to know your complete mode l number and serial
number. You can find this information on the model and serial
number label located on the inside wall of the refrigerator
compartment.

Dealer name__________________________ __________________________
Address________ _______________________________ ___ ______________
Phone number___________ ___ ________________________________ ___ _
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________

01/00

2212430

© 2000 All rig hts r e se rv ed. ® Registered Trademark of Crosley Printed in U.S.A.

3/00