Crimestopper Security Products SV-9155 User Manual

SV

-

9155

View Mirror

4.2” Replacement
Rear

Monitor

INSTALLATION INSTRUCTIONS:

The SV-9155 is a replacement Rear View Mirror. It replaces your factory mirror and adds the
convenience of a 4.2” LCD screen which can be used for a reverse and an external DVD
source. The Reverse Camera Input will automatically switch on when the vehicle is dropped into
reverse. The SV-9155 can be hooked up to any SecurView™ or PlateCam™ camera.

FEATURES:

• Replacement Rear View Mirror with Built-In 4.2” LCD Screen for viewing Reverse
Camera

• Compatible with any Camera which uses an RCA video output

• Provides extra safety precaution when backing-up

• Maintains the “Factory” look of the vehicle

• Optional Normal Image and Reverse Image

• Compatible with 70%-80% of GM, Ford and Toyota vehicles.

• Compatible with 12V and 24V DC vehicles

• Built-In Interface to allow user to switch between to different video inputs

• High-Low voltage and short circuit protection

• Reverse camera input will appear on screen whenever vehicle is shifted into reverse

• Anti-Glaring treatment on Screen

INSTALLATION

INSTALLATION PRECAUTIONS:

1. Secure the mirror tightly to the windshield so that it can not become loose under any

circumstances (Sudden braking, accidents, etc) and cause injuries to the occupants of the
vehicle.

2. Do not install the mirror in an area that is in close proximity with an airbag, as this could cause

injury if the airbags are deployed.

3. Make sure to connect the mirror to the correct voltage. Failure to do so may result in damage

to the mirror or injury to the vehicle occupants

4. Do not submerge the mirror under water. The mirror is not waterproof and this will damage

the electrical components inside of it.

5. The Mirror has built-in circuitry to reverse the image so objects on the right of vehicle appear

on the right and objects on the left appear on the left when looking at the monitor. (See
Reverse Imaging in next section for more information.)

6. Do not attempt to take apart the mirror under any circumstances.

7. Do not operate the monitor if the mirror housing has been damaged.

MIRROR MONITOR INSTALLATION:

1. Remove the OEM Rear View Mirror from the vehicle. Usually the OEM mirror should unscrew

from a mounting plate on the vehicle’s windshield. Do not use excessive force when removing
the factory mirror.

2. Some factory rear view mirrors may have “Reading Lamps” or “Map Lights” built into them. In

order to remove this type of mirror, there will be a wiring harness that will need to be
unclipped before you can proceed with the removal of the mirror itself. Make sure the vehicle
owner is aware that the SV-9155 does not have any lamps built into it and that they will be
losing this accessory once the factory mirror is removed.

3. Once the factory mirror is removed, place the SV-9155 into the position of where the factory

mirror was located for a fest fit.

4. Adjust the angle of the SV-9155 to the best position by rotating the ball-joint of the adjustable

mounting bracket on the back of the mirror.

5. Remove the screw and silver lug form the base of the SV-9155 mounting bracket.

6. Slide SV-9155 Mounting Bracket over the factory mounting plate on the windshield.

7. Make sure that the mounting bracket fits over the entire windshield mounting plate.

8. Re-insert the screw into the mounting bracket and secure the mirror tightly over the factory

mounting plate.

9. DO NOT overturn the mounting screw. This will cause the screw’s threads to strip and may

also damage the threads inside the mounting bracket itself.

10. Route the electrical cable of the SV-9155 up the windshield and underneath the headliner of

the vehicle

NOTE: The holes in the back and the bottom of the unit are provided for ventilation to prevent

overheating of the unit and to ensure reliable operation of the monitor equipment. These holes
must not be blocked with any kind of electrical tape or silicon. If the ventilation holes are
blocked, this could cause damage to the monitor