Crimestopper Security Products RS-1304DP, RS-1301DP, RS-1303DP, RS-1300DP User Manual

RS-1301DP/1303DP/1304DP 1 WAY SYSTEMS

This device complies with FCC Rules part 15. Operation is subject to

ause harmful

interference, and (2) This device must accept any interference that

may be received, including interference that may cause undesired

operation. The manufacturer is not responsible for any radio or TV

cations to this equipment.

Such modification could void the user’s authority to use the

RS-1604TW1/1704TW2/1804FM 2-WAY SYSTEMS
RS-1300DP ADD-ON MODULE

DP SERIES (Data port)

REMOTE ENGINE STARTING SYSTEM

INSTALLATION INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS on your choice of a “Cool Start” System with Data Port Technology for direct connection for bypass
module by Crimestopper Security Products Inc. This booklet contains the information necessary for installing your remote
starter system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech
Support number below.

Note: Some features will not be available on units with 1 button, 2 button, and 3 button remotes.

DISCLAIMER:

This installation book is designed for the installer or individual with an existing understanding of automotive electrical
systems, along with the ability to test and connect wires for proper operation. To ease installation, we suggest that you
READ THIS MANUAL before beginning your installation. This book is provided as a GENERAL GUIDELINE and the
information contained herein may differ from your vehicle. Crimestopper Security Products, Inc. and its’ vendors shall not
be liable for any accident resulting from the use of this product. This system is designed to be professionally installed into
a vehicle in which all systems and associated components are in perfect working condition.

TECHNICAL SUPPORT: [phone]

Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
E-mail: [e-mail]

CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063

REV A 2.07.2006

the following two conditions: (1) This device may not c

interference caused by unauthorized modifi

Pre-Installation Considerations….………...……...………………………………………………………………..….………..2

Installation Cautions & Warnings………………………………………………………………………………..….....……..…3

Wiring……..……………………....…………………………………………………………………………………...………...3-7

Wiring High-Current Connector…….…………………………………………………………………………....……..........8-9

Power Door Lock Wiring...…………………………………….…………….……..…………...……………..….………..10-11
Smart Tachless, Tach Reference, Tach Finder, & Timed Crank Modes…………………..…..………...….……..…12-15
Diesel Glow Plug Delay..………………….……………………………...……………………...…..…………..…….………16

Options Programming ………..……………………….……………………………..……………..…….....………..……16-21

Transmitter / Transceiver Programming……………………….……………….……………..………...….………….....….22

2 Vehicle Operation.……………………………….………………………………...…………………….….……..…………23
Troubleshooting “Before You Call” Section……………..…………………………..…………….……….……..….………24
Jumper Pin, Antenna, System Diagram & Data port Diagram………………………………..………….……….……25-28

PRE-INSTALLATION CONSIDERATIONS

BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS

BRAKES, ENGINE / BODY COMPUTER AND BATTERY).

PLAN OUT YOUR INSTALLATION and determine most suitable locations for all components to be placed. These components
include: the module itself, valet/program button, possible relays, and antenna/receiver (RS1301/3/4DP, 1604TW1,1704TW2,
1804FM only, the RS-1300DP model does not include antenna or remotes.) Allow enough wire to create a service loop with strain
relief, should servicing be required. This will also allow easier access and mounting.

DAMAGE to the CoolStart unit resulting from incorrect installation or failure to follow guidelines stated in this book will not be
covered under warranty and will be subject to repair or replacement charges.

USE A VOLT/OHM METER to test and locate all connections. Test Lights can damage a vehicle’s computer systems.

ADDITIONAL PARTS, which are not included with this unit, may be needed for your particular vehicle. These items may include

extra relays or Anti-Theft System Bypass modules.

TABLE OF CONTENTS

2

INSTALLATION CAUTIONS & WARNINGS

**FOR SAFETY REASONS, DO NOT INSTALL in vehicles with MANUAL TRANSMISSIONS.** If accidentally left in

gear, a remote started vehicle could become a self-propelled threat to life and property.

DO NOT extend the Remote start ignition harness length. Mount the module so that main harness reaches all ignition
switch wiring. Extending these wires could result in poor or improper performance.

DO NOT route any wiring that may become entangled with brake, gas pedals, steering column or any other moving parts
in the vehicle.

DO NOT exceed the rated output current of any circuit on the Remote start module. Failure to observe this warning will
result in damage to the unit not covered under warranty.

DO NOT remote start the vehicle in a closed garage! Make sure that the garage door is open or there is adequate
ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes.

WIRING

PIN 1: YELLOW/WHITE: (-) HORN CHIRP/HONK OUTPUT

Connect to the LOW CURRENT Negative Horn Trigger wire usually located near the steering column. If the vehicle horn
circuit requires +12V, then a relay is required. RELAY WIRING: Connect the Yellow/White wire to terminal #85, connect
relay terminals #86 and #87 to +12V constant power. Connect terminal #30 to the +12V positive Horn activation wire.

PIN 2: BLACK: MAIN SYSTEM GROUND

Connect to chassis metal of the vehicle. An existing bolt or screw may provide an adequate ground, or drill a small hole,
scrape away paint and attach using a sheet metal screw & star washer. This wire must be connected to a proper ground
or undesirable and inconsistent operation will occur. Do not use Factory ground locations.

PIN 3: YELLOW/BLACK: (-) IGNITION OUTPUT -or- ANTI-GRIND/STARTER DISABLE OUTPUT

This negative output wire is programmable and can function two different ways. It can be used as a Negative Ignition
output for GM Anti-theft and Transponder Bypass modules, or it can be programmed to function as an Anti grind/Starter
Disable output. As a Negative Ignition wire, this wire turns on when the remote start button is pressed and stays on
through the duration of the remote start. As an Anti grind/Starter disable this wire activates when the Lock button on the
remote is pressed and during remote start. When using this wire for an Anti grind/Starter disable, an optional Relay is
needed to interrupt the Starter circuit. The starter disable circuit adds an anti-theft feature to this remote start system and
prevents accidental grinding of the starter if key is turned too far after a remote start. See diagrams on NEXT PAGE.

3

WIRING

PIN 3: YELLOW/BLACK FOR NEGATIVE IGNITION OUTPUT: (Relay and/or Module not included)

ANTI-THEFT/

YELLOW/BLACK

Diode isolate

OR

OR

85

86

TRANSPONDER

MODULE

if using both!

30 87

+12V CONSTANT

3rd IGN

(If needed)

IGN SW.

PIN 3: YELLOW/BLACK: FOR ANTI-GRIND/STARTER DISABLE OUTPUT: (Relay not included)

TO

MOTOR

IGN 1

IGN 2

ACC

START

BROWN

YELLOW/BLACK

CUT

8685

MAKE CERTAIN TO CONNECT "BROWN" START OUTPUT WIRE TO

MOTOR SIDE OF ANTI-GRIND/START DISABLE RELAY.

MAKE SURE 86 TERMINAL HAS POWER WITH IGNITION ON AND CRANK

4

WIRING

PIN 4: BROWN: (-) AUX OUTPUT (TRUNK POP) or DOME LIGHT ILLUMINATION OUTPUT

This output is programmable for two modes of operation. See Programming Option Section.

Mode (1) DEFAULT: Provides a Ground pulse when button #3 (Trunk) on the remote transmitter is pushed to activate
a factory electric trunk release or other optional accessory.
Mode (2) ALTERNATE: Provides a Ground output for 30 seconds when the unlock button is pressed for use as a dome
light illumination output.

Note when using the Brown wire as a Trunk Pop, you may also need or want to program option #14 so the system
also provides an Unlock signal when the trunk pop is activated. This may help to prevent unnecessary triggering of
Factory Alarm systems or you may want the convenience of having the door unlock at the same time.

BROWN WIRE: TRUNK OUTPUT or DOME LIGHT

+12V CONSTANT

BROWN

85

86

30 87

+12V CONSTANT

Trunk Soleniod

OR *

(Default)

-OR-

Dome Light

Circuit

5

* Test activation circuit in vehicle.

Connect to+12V for Positive circuits

or Ground for Negative circuits. Relay

not included.

WIRING

PIN 5: GREEN: (-) START ACTIVATION INPUT, OEM INTERFACE or TURBO TIMER INPUT

See descriptions & diagrams below.

Mode (1) [Default (-) Neg. Start Activation] This wire
allows a host (or parent) alarm’s or keyless entry system
to activate a Remote Start by sending a 1-Second
Negative signal to the Green input wire to trigger a
remote engine start or stop. Connect the Green wire to
the host system’s Auxiliary channel output wire.

Mode (2) [Alternate OEM Interface] This mode allows the
system to Remote Start or Stop when 3 successive
Negative pulses are sent to the Green input wire.
Connect the Green input wire to the Negative lock signal
wire of the factory system. If your Factory OEM system
does not have this type of signal, then a relay is required.

TURBO TIMER INPUT [No programming required] This
wire allows the system to keep a vehicle running for 1-5
minutes [selectively] after removing the key. This mode
requires the use of a momentary switch that is not
included with the kit. Connect a 2-pole momentary
switch with one side to chassis Ground and the other
side to the Green input wire. If you own a turbo or turbo
diesel vehicle, you can now allow the CoolStart system to
keep your engine running for 1-5 minutes after
exiting/locking your vehicle to cool-down without the need
for an external “Turbo Timer”.

NOTE: The turbo timer button will also trigger a
remote start if it is inadvertently pressed when the
vehicle is not running. Please note this when
installing the button and choose a location out of harm’s way.

RS-1300 EXPANSION (Default)

GREEN

1 sec. (-) pulse

RS-1300 OEM INTERFACE

GREEN

3 Consecutive

(-) pulses

New TURBO TIMER MODE

GREEN

FACTORY KEYLESS

AFTERMARKET

ALARM / KEYLESS

(Aux Channel

Output)

MODULE

Momentary

Switch

(Not included)

6

WIRING

PIN 6: GRAY: (-) NEGATIVE HOOD PIN SWITCH (REQUIRED FOR PROGRAMMING)

Connect the Gray wire to a switch that is at ground when the hood is open. If an existing switch is not available, then we
recommend one to be installed. When this wire is grounded, the remote start is inhibited. If hood is opened on a remote
started engine, the unit will immediately shut the motor off. The unit will not attempt to start if hood is open. The hood pin
is also used for remote transmitter programming.

PIN 7: PINK: NEGATIVE GLOW PLUG

Connect Pink wire to indicator circuit that shows a (-) Signal while the “WAIT TO START LAMP” is on. When this wire is
used, the system will wait until light turns off before attempting a remote start.

PIN 8: PURPLE: (+12V) BRAKE RESET

Connect the Purple wire to the side of brake pedal switch that shows +12 volts ONLY when pedal is depressed. This is the
wire that turns off the remote start once the driver’s key is in the Ignition and turned to the ON position.

PIN 9: ORANGE/BLACK: (-) OEM DISARM OUTPUT

This wire provides a Ground pulse to disarm the vehicles' Factory anti-theft system prior to a Remote Start. Connect this
wire to the vehicles' anti-theft disarm wire. This wire is sometimes found coming off the Driver's door key switch or at the
Factory Anti-theft control module. This wire may not be needed if Factory Security only requires a door unlock pulse.

PIN 10: ORANGE: (-) OEM REARM OUTPUT

This wire provides a ground pulse to rearm the vehicles' FACTORY anti-theft system after a timed-out or aborted remote
start. Connect this wire to the vehicles' anti-theft rearm wire or to the door pin circuit depending on your requirements.
This wire may be needed to pulse the door pin circuit on vehicles with retained accessory power.

PIN 12: RED/WHITE: TACHOMETER INPUT

When installing the system in Tach mode, this wire must be connected to a valid source of AC voltage. This wire allows
the unit to sense the engine running and control the starter motor. See TACH REFERENCE MODE.

PROGRAM/OVERRIDE SWITCH: 2 PIN PLUG (REQUIRED FOR PROGRAMMING & LEARNING REMOTES)

This switch is used for programming features, transmitters, valet mode, and to override the optional starter disable (if
installed) in the event of a non-operating remote control.

LED: 2 PIN PLUG (OPTIONAL)

The LED is used as a VALET/PROGRAMMING indicator and it will also FLASH for use as security deterrent when the
optional ANTI-GRIND/STARTER DISABLE output is programmed.

7

WIRING: 7-PIN HIGH-CURRENT CONNECTOR

BROWN: +12V STARTER OUTPUT 30A:

Connect to circuit in the vehicle that has power ONLY while the STARTER MOTOR is CRANKING.

GRAY: +12V ACCESSORY OUTPUT 30A:

Connect to circuit in the vehicle that provides Accessory Power for systems such as HEAT and A/C. Typically, this wire
turns ON with the first position of the key, DROPS OUT WHEN CRANKING, then returns as the engine starts and runs.

(2) RED: +12V POWER INPUT WIRES (30A Fused):
Connect to both of these leads to +12V Constant Power. We recommend the BATTERY POSITIVE
TERMINAL.

PINK: +12V IGNITION OUTPUT 30A:

Connect to circuit in the vehicle that provides true Ignition Power for systems such as Spark and Fuel. Typically, this wire
turns ON with the second position of the key, STAYS ON WHEN CRANKING, and continues ON as the vehicle runs.

PINK/WHITE: +12V MULTI-FUNCTION OUTPUT 30A (JUMPER SELECTABLE):

This is an optional multi-function output wire the can be configured as a Second IGN, ACC or STARTER output. Some
vehicles require more than just one IGN, ACC, or STARTER wire in order to start and run successfully. If this is the case
for your particular vehicle, then use the jumper pin located under the access panel on the top of the CoolStart control
module to configure this wire to suit your needs. The DEFAULT setting is IGNITION. See Jumper Pin Diagram.

WHITE: +12V or (-) NEGATIVE PARKING LIGHT OUTPUT:

Connect to vehicle parking light circuit at the back of light switch or if this is not possible, connect directly to one of the
parking lights at the front of the vehicle. If your vehicle has a multiplex lighting system that requires a (-) Negative parking
light output, then open the access door on the top of the module and move the jumper. See Jumper Pin section. Some
European vehicles require separate left and right circuits. Use a dual relay or diodes to isolate the output. Note the
current limit on the Negative parking light output. You may require an external relay to prevent damage to the unit.

(1) Default parking light output is +12 volts.
(2) Use an external relay for vehicles that draw excess current from extra running lights, light bars, or trailers.
Parking light output is limited to (+) 10 amps or (-) 500 mA only.

SEE DIAGRAM on NEXT PAGE

8

WIRING: 7-PIN HIGH-CURRENT CONNECTOR

Current systems or you will risk damaging the

unit and creating a hazardous condition! Use Part #CS

-

403 relays for circuits up to 70 amps.

7-PIN High Current

Connector

TOP

PARKING

LIGHTS

FUSE

+10A or 500mA (-)

FUEL

PUMP

+ STARTER

-

COIL

WHITE

ENGINE
ECU

RED

PINK/WHITE

GRAY

RED

BROWNPINK

Diagram not to scale,

for illustration purposes

only. Your vehicle may

differ.

FUSE

30A

FUSE

30A

+

VEHICLE

BATTERY

-

START 2

IGN 2

OR

ACC 2

IF NECESSARY

NOTE: Heavy duty/High Current Ignition circuits greater than 30 AMPS. Industrial vehicles, dual AC, etc. require high-

current relays. DO NOT use the outputs of the Remote Starter for High-

IGN

ACC

IGN. SWITCH

H/V/AC

9