Crimestopper Security Products EZ-30DP, EZ-33DP, EZ-34DP, EZ-31DP User Manual

EZ-30DP/31DP/33DP/34DP

1-WAY SYSTEM

DP SERIES II (Data Port)

OPERATING INSTRUCTIONS

**IMPORTANT NOTES:- FOR EZ-30DP MODEL ONLY**

EZ-30DP Model is an add-on/expansion unit, without remotes or an antenna that must be controlled by an existing
alarm or keyless entry system. The “Infinity Run” feature is not available on an EZ-30DP system. Most of the
remote start features can be controlled through an existing factory or aftermarket remote keyless entry or alarm
system. Pressing an auxiliary button on an Aftermarket system or pressing a button 3 times on a Factory keyless
remote can activate a remote start using the EZ-30DP. This is referred to in this manual as activating the “Green
Start input wire”.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Remote

Start connections, Flashing lights, and Brake Reset. For programming, the hood pin and program button are
required.

-OPTIONAL: These features are to be connected only if desired or agreed upon by the customer and the installing
dealer i.e. Door Locks, Trunk Pop, Dome Light Illumination, Horn-Honk, Anti-Grind, etc. These features may also
require additional parts and/or labor fees. Consult with your installer beforehand to be sure of what is going to be
installed with your particular system.

CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063

REV B - 07.2006

This device complies with FCC Rules part 15. Operation is
subject to the following two conditions: 1) This device may not
cause interference, and (2) this device must accept any
interference that may be received, including interference that
may cause undesired operation. The manufacturer is not
responsible for any radio or TV interference caused by
unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.

2

TABLE OF CONTENTS

Operation Cautions & Warnings…….……………..….…………………………………….…………………………2
Using the Remote Transmitter…………………………………………………………………………………...…….3

Status LED……………………………………………………………………………………………………………….4
Remote Engine Control…………….…..…………………………………………………………………….……….3-8

Turbo Timer Mode……………………………….……………………………………...……….………………………9
Convenience and Safety Features……………………………….……………………………………...……..…10-11

Transmitter Programm ing….…………….…………………………………………….…………………………....…12

2 Vehicle Operation.…………………………………….………………...……………………..….………….………13
Troubleshooting “Before You Call” Section……………..……………………………………………………..….14-15

Battery Replacement.…………………………………….………………...……………………..…………….………15

OPERATION CAUTIONS & WARNINGS

CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident resulting
from the use of this equipment. This system is designed to be professionally installed into a car or vehicle in which
all item s, such as parking brake and all associated components, door switches, transmission shift linkage, throttle
linkage, and all engine safety features, are in perfect working condition.

DO NOT install the Remote Engine Starting System on MANUAL TRANSMISSION vehicle s. If accidentally left
in gear the vehicle could become a self-propelled threat to life and property.

IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system
and its safety features. B) Check for proper operation of the system prior to accepting delivery of the vehicle from
the installation facility. C) Check and maintain the condition of the vehicle and all items relative to the proper
operation of this system and its safety features. D) Always leave the doors and windows closed and locked to
protect against accidents and theft.

DO NOT remote start the vehicle in a closed garage. Make sure that the garage door is open or there is
adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide
fumes.

3

USING THE REMOTE TRANSMITTER

EZ START

EZ-31DP II

#1

REMOTE

START

FLASHLIGHT

VEHICLE 2

#1

LOCK

EZ START

EZ-33DP II

#2

UNLOCK

FLASHLIGHT

VEHICLE 2

#3

REMOTE

START

#1

LOCK

#3

TRUNK

EZ START

EZ-34DP II

#2

UNLOCK

FLASHLIGHT

VEHICLE 2

#4

REMOTE

START

For EZ-30DP II

The EZ-30DP II model does not include remote transmitters, as it is designed for the expansio n of a “parent” remote
keyless or alarm system.

For EZ-31DP II

The transmitter supplied with this system has 1 button, flashlight and car 2 side button. The button configuration is
Factory-set and unchangeable. See Page 13 for additional information on how to use your remote to operate a
second vehicle equipped with an EZ-30 series II system.

For EZ-33DP II

The transmitter supplied with this system has 3 button, flashlight and car 2 side button. The button configuration is
Factory-set and unchangeable. See Page 13 for additional information on how to use your remote to operate a
second vehicle equipped with an EZ-30 series II system.

For EZ-34DP II

The transmitter supplied with this system has 4 button, flashlight and car 2 side button. The button configuration
is Factory-set and unchangeable. See Page 13 for additional information on how to use your remote to operate
a second vehicle equipped with an EZ-30 series II system.

BUTTON #3 and #4 (#1 on EZ-34DP II) Programmable for 1 or 2 button presses

These buttons are programmable for one or two button presses to activate trunk release or remote start. This
option is selectable by your installer.

*Default = 1 press*

4

STATUS LED

LED Operation: (install option)

LED will flash when remotely locking your doors.
LED will remain solid in Valet Service mode.

REMOTE ENGINE CONTROL

REMOTE ENGINE STARTING - SUCCESSFUL START:

1) Press the remote start button for at least 1/2 second (*default). (For EZ-30DP II models, consult your installer).

2) Parking lights flash once, return solid, and the Ignition/Acc circuits turn on.

3) After a few seconds the Starter Motor engages. The parking lights and Acc circuits will turn off while cranking.

4) Engine Starts and Runs. Parking Lights and Acc turns back on, and the doors lock.

5) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can be
turned off with remote transmitter by pressing and releasing the Start button. (F or EZ-30DP II model, activate the
Green Start input wire)

SOLID

FLASH 1X

AFTER

IGN

4

THEN

SOLID

THE REMOTE STARTER B UTTON IS PROGRAMMABLE FOR 1 OR 2 PRESSES

SEC.

REMOTE ENGINE STARTING - UNSUCCESSFUL START

In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then
attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank time of
up to13 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 13 se conds
to help prevent damage to the starter from over cranking.

1) If engine starts on 2nd or 3rd attempt, see steps 4 & 5 above of "Successful Start".

2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER
ATTEMPTS WILL BE MADE AUTOMATICALLY

STARTER

5

REMOTE ENGINE CONTROL

TURNING OFF A REMOTE STARTED ENGINE:

1) Engine is running in Remote Start (Parking lights ON).

2) Press and release the remote start button or double press (If option #6 is on). (For EZ-30DP II model,
activate Green Start input wire.)

3) Engine & parking lights OFF, Doors re-lock/re-arm.

ENTERING YOUR REMOTE STARTED VEHICLE:

1) With engine running, Unlock system with remote (If equipped) or open door with key.

2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)

3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park.

4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key is
now controlling your vehicle.

REMOTE START RUN TIME RESET: DOES NOTS APPLY TO EZ-30DP/31DP II

You can now reset the engine-run timer to allow for more running time after remote start has already occurred
using the remote control. After a successful remote start, press both the Lock & Unlock buttons together for at
least 2 seconds. The parking lights will flash 3 times and internal engine timer will reset back to zero minutes.

IDLE DOWN MODE:

This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you exit
the vehicle. The vehicle is put into a remote running condition before you exit and it will remain running for the
programmed run time or until you come back.

Examples:

• You pull up to a convenience store for a quick stop, "Idle Down" m ode keeps engine running when you exit the
vehicle, (with keys in hand) remote lock doors or arm alarm. W hen you return, unlock, turn ignition ON and drive
away.