CrimeStopper SP-402 Operating Instructions Manual

SP-402

Combo Alarm & Remote Engine Starting System

OPERATING INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS on your choice of the SP-402 by Crimestopper Security Products Inc. This booklet contains the
information necessary for operating your system. If any questions arise, contact your installation dealer or
Crimestopper Security Products Inc.

CONTACT INFORMATION:
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific

Website: www.crimestopper.com

CRIMESTOPPER
SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063

This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: 1) This device may not cause
interference, and (2) this device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modification to this
equipment. Such modification could void the user's authority to
operate the equipment.

REV 09-2012

2

USING THE REMOTE TRANSMITTER

VEH 1 = Blue

LED

R

emote AUX Outpu

ts

Lock / Arm

VEH 2 = Red LED

AUX 1 = Trunk + Lock
AUX 2 = Trunk + Unlock
AUX 3 = Trunk + Start
AUX 4 = Lock + Start

VEH

Unlock / Disarm
Trunk Release
Vehicle Select
Remote Start

NOTE: The VEH button can be used to keep remote control from accidentally operating your vehicle.

See Page 17 for additional information on how to use your remote to operate a second vehicle

3

QUICK CHART BUTTON FUNCTIONS

Press and Hold for 2

Press and Hold for 2

for Trunk Pop Aux #1

thru

thru

thru

Valet Service Sensor

thru

Button

Plus

Button

Functions

Lock Doors & Arm

System

Unlock Doors &

Disarm System

Trunk Pop

Start or Stop engine

Silent Arm / Disarm

ON / Off

Aux # 1

Button Options Button Button FunctionsButton Options

Press and Hold 2

Seconds for Panic

Mode

Press twice for

second door unlock

Press and Release

Press for Remote

Start. Three options

available

No Arm / Disarm

Chrip from Siren or

Horn

Valet Mode when

Disarmed. Sensor

On/Off when Armed

VEH
VEH

Plus

Plus

Plus

Plus

Selects between

Vehicle #1 and

Vehicle #2

Used to Disable
Remote Control

Activates

Activates

Activates

Activates

Aux #1

Data

Aux #2

Data or wire

Aux #3

Data or wire

Aux #4

Data or wire

seconds

seconds

Data Module Sliding

Door

Steady Momentary

or Data Module

Sliding Door

Momentary, Timed

or Latched Output

Momentary, Timed

or Latched Output

4

OPERATING INSTRUCTIONS - ALARM

ARMING / LOCKING

Press the Lock Button on the remote control. The System will arm emit one siren chirp, one light flash, and
the LED will begin to flash. Power locks will lock (if equipped). Starter disable circuit will turn on. The 2-Way
LCD Pager will beep once while displaying a Locking symbol. After a short delay to allow the vehicle and
electronics to settle, the system will be completely armed.

DISARMING / UNLOCKING
Press the Unlock Button on the remote control. The System will disarm and confirm with two siren chirps, two
light flashes, and the LED will turn off. Power locks will unlock and Interior Dome light will turn on (if installed
with these optional features). The 2-Way LCD Pager will beep twice while displaying an Unlock symbol.

SELECTIVE SILENT ARMING / DISARMING

Plus

LED will be the only indicators of Arm/Disarm status. The LCD will Display a musical note with an “Ø” when
the system is armed or disarmed without a chirp.

DRIVER’S DOOR PRIORITY UNLOCK: Optional connection required

This option separates unlock of the driver’s door from the passenger doors with the remote control. The first
press of unlock button will unlock just the driver’s door. Pressing the unlock button a 2nd time within 12
seconds will unlock the passenger doors.

DISARMING WHILE TRIGGERED

Disarming the System while it is triggering requires TWO presses of the Unlock Button. The first press Resets
the alarm cycle only (system still armed) while a second press will disarm/unlock the system.

SELECTIVE SHOCK SENSOR DISABLE

chirps indicating the shock sensor bypass for this arming cycle only. This is feature useful when parking near
railroad tracks, airports, or areas with excessive loud machinery or noise to prevent the nuisance of
unnecessary false alarms.

To Arm or Disarm the system without siren chirps, press and release both the Unlock and Start
Button at the same time. The System will Arm or Disarm without siren chirps. Flashing lights and

To arm the alarm and bypass shock sensor protection, press the Lock Button as normal then
press and release the Lock & Unlock Button together within 2 seconds. You will hear 3 extra siren

5

OPERATING INSTRUCTIONS - ALARM

ALARM TRIGGERS

If there is an intrusion into the vehicle, a hard impact to the body or the ignition is turned on, the alarm will
sound and flash the lights for 1 minute. After 1 minute, the trigger cycle will automatically stop and alarm will
remain armed to continue protecting the vehicle. If a door is left open after an intrusion then the unit will cycle
a maximum of 2 minutes and continue to protect the other un-tampered or unopened zones.

LCD REMOTE PAGING / ZONE VIOLATIONS

When the system is triggered, the alarm sends a paging signal to the remote. If you are within range, you will
receive a paging signal that will light up the LCD Screen Red. The display will show an icon of what caused
the violation. The paging remote will also vibrate and beep to notify you the vehicle has been tampered with.

OPEN DOOR ALERT / BYPASS

Upon arming, this system will warn you 5-60 seconds later if a door is left open. The LCD pager will vibrate
and beep (5X’s) along with displaying the open zone on your LCD screen. This zone will be bypassed until the
door is closed; otherwise, the alarm will continue to protect all other zones.

PRE-WARNING SHOCK PROTECTION

The Pre-Warning (Warn-A-Way) feature will activate when a low-level shock or vibration is detected by the
system’s shock sensor. The alarm will chirp the siren 5 times and flash the lights once to help deter any
further tampering with the vehicle. The pager / remote will beep and show a Hammer Icon.

PASSIVE ARMING MODE (Programmable)

Passive (automatic) Arming occurs 30 seconds after the ignition is turned off and the last door is closed.
Upon closing the last door, the unit will flash the lights twice and LED will be flashing rapidly to confirm passive
countdown. If a door is re-opened within the 30-second period, the countdown stops and begins again when
the door is closed. Passive arming provides failsafe protection in case you forget to arm the system.

PASSIVE LOCKING (Programmable)

The system can be programmed to passively lock the doors when the system passively arms or rearms. The
default setting is OFF because passive locking increases the risk of locking the keys in the vehicle when the
system arms/locks passively, without you pressing the remote.

6

OPERATING INSTRUCTIONS - ALARM

REMOTE PANIC PROTECTION

To sound the alarm in an emergency or to draw attention to your vehicle, press and hold the Lock button for at
least 3 seconds until the siren / horn sounds. Press the Unlock button to reset panic mode. The LCD display
will flash most of the icons and emit 10 beeps when the Panic Mode is triggered.

TRUNK / HATCH POP (Optional, Remote AUX. 1 Output)

This feature is designed to interface with existing Factory power trunk or power hatch release systems and
may require additional parts and/or labor charges. To eliminate the possibility of accidentally opening the
trunk, there are (3) options for button press selection. This option will allow you to change whether the Remote
starter and Trunk release activate by a:

1. Double button ½ second presses.

2. Single ½ second press. *Default = Single ½ second press*

3. Press and Hold 2 seconds. This output stays on until trunk button is released.

REMOTE AUX. 1 thru Data module for sliding doors only

This feature requires a Databus module to operate.

Plus

REMOTE AUX. 2 Output (Optional, requires special programming)

Plus

Press the Trunk and Unlock button for more than 2 seconds.

REMOTE AUX. 3 Output (Optional, requires special programming)

Plus

REMOTE AUX. 4 Output (Optional, requires special programming)

Plus

Press Trunk plus Lock at same time to activate Aux 1.

This system contains a 2nd Auxiliary output to activate other accessories or devices. This
momentary output will stay active as long as the remote button is held down. There is no LCD /
Pager confirmation for Aux. 2 output. To activate the 2nd Auxiliary output:

This system contains a 3rd Auxiliary output to activate other accessories or devices. This output
is programmable for a momentary, timed or Latch output. To activate the 3rd auxiliary Output:
Press the Trunk and Start Button at the same time.

This system contains a 4th Auxiliary output to activate other accessories or devices. This output
is programmable for a momentary, timed or Latch output. To activate the 4th auxiliary Output:
Press the Lock and Start Button at the same time.