Crimestopper SP-400 Operator's Manual

SP-400

Remote Control Alarm & Remote Engine Starting System

OPERATION INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS on your choice of a Super Rage™ Alarm & Remote Engine Starter with DP Technology
by Crimestopper Security Products Inc. This booklet contains the information necessary for operating your

system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Power,

Ground, Lights, Siren, etc.

-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Door
Locks, Horn Honk, Dome light illumination, Starter Kill, L.E.D., Trunk Pop, etc. These features may require
additional parts and labor charges. Consult with your installer about these features before installation.

CONTACT INFORMATION:
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific

Website: www.crimestopper.com
E-mail: [e-mail]

CRIMESTOPPER
SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063 REV 11-2008

This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: 1) This device may not cause
interference, and (2) this device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modification to this
equipment. Such modification could void the user's authority to
operate the equipment.

TABLE OF CONTENTS

Operation Cautions & Warnings……..………..……………….…………………………………………….………..…2
Quick Guide……………………………...………………………………………………………………………………...3

Operating Instructions - Alarm…………………………………….………………….………..……………..…….....4-6

LED Diagnostics………………..……………………………….…………………………………….………..……...….7
Remote Engine Control ………………………...…………………………………………………….………….…..7-11

Optional Turbo Timer Mode……………………...………………………………………………..……..…......….12-13

Anti-Carjack Protection...……………………………………….………….……..…………...…………..……..…..…14

Transmitter Programming……………………………….……………………………………………..………….....…15

Remote Start Diagnostics…..………………..……………………………………………………………………...….16
Battery Replacement………..………………..……………………………………………………………………...….16

OPERATION CAUTIONS & WARNINGS

CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident

resulting from the use of this equipment. This system is designed to be professionally installed into a car or
vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features,
must be in perfect working condition.

DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to
repair and / or replacement charges.

IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this
system and its safety features. B) Check for proper operation of these safety features prior to accepting
delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all
items relative to the proper operation of this system and its safety features.

DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door
is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death
from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature
of the unit

2

REMOTE

OPERATION

QUICK GUIDE

Replacement Battery

SLIDE COVER

UP

DOWN

GP23A (12volt)

The slide cover is used to protect pressing buttons by accident.
Move cover to middle position to block all 4 buttons.

2nd Vehicle Button # 5: The LED will Flash Blue while in 2nd Vehicle Mode.
2nd Function Button # 6: The LED will turn solid Red for AUX 2, AUX 3, AUX #4

§ AUX #2: Press button 6 then press button 1 (Lock Icon).

§ AUX #3: Press button 6 then press button 2 (Unlock Icon).

§ AUX #4: Press button 6 then press button 4 (Start Icon).

2nd Vehicle

2nd Function

3

OPERATING INSTRUCTIONS - ALARM

Arming / Locking:

Press and release button #1 (Lock symbol) on the transmitter. The System will arm and confirm with one siren
chirp, one light flash, and the LED will begin to flash. Power locks will lock (if equipped). Starter disable circuit
will turn on. After a short delay to allow the vehicle and electronics to settle, the system is completely armed.

Disarming: / Unlocking
Press and release button #2 (Unlock symbol) on the transmitter. System will disarm and confirm with two
siren chirps, two light flashes, and the LED will turn off. Power locks will Unlock and Interior Dome light will
turn on (if installed with these optional features)

Disarming While Tripped (Triggered):

Disarming the System while it is triggering requires TWO presses of the #2 Unlock Button. The first press of
Button #2 Resets the alarm cycle only (system still armed) while a second press will disarm/unlock the system.

Silent Arming/Disarming (On demand):

To Arm or Disarm the system without siren chirps, press and release both Buttons #2 (Unlock) and #4 (Start)
at the same time. System will Arm or Disarm without siren chirps that one time. Flashing lights and LED will
be the only indicators of Arm/Disarm status. If the system was tripped while you were way, 4 chirps will be
heard to notify you that the system was tripped.

Silent Arming/Disarming (Chirp Defeat):

This system can be programmed to silent arm and disarm using the normal lock and unlock buttons. Flashing
lights and LED will be the only indicators of armed or disarm status. Check with your installer or follow
programming option instructions in the installation manual.

Alarm Triggering

An intrusion into the vehicle or hard impact to the body will sound the alarm and flash the lights for 1 minute.
After 1 minute the trigger cycle will automatically stop and alarm will remain armed to continue protecting the
vehicle. If a door is left open after an intrusion then the unit will cycle a maximum of 2 minutes and continue to
protect the other un-tampered or unopened zones.

Prior intrusion Alert

This system will notify you if the alarm was tripped while you where away. Upon disarming, the two normal
disarm chirps will be heard then the system will emit 4 additional siren chirps. Check your vehicle for any
signs of a break in or tampering. Also see LED Diagnostics Section to determine the cause of the trigger.

4

OPERATING INSTRUCTIONS - ALARM

Remote Panic Protection

To sound the alarm in an emergency situation or to draw attention to your vehicle, press and hold Button #1
(Lock) for at least 3 seconds until the siren sounds. Press Button #2 (Unlock) to reset panic mode.

Arming With Shock Sensor Bypass

To arm the alarm and bypass shock sensor protection, press Button #1 as normal then press and release
Button #1 and #2 together within 2 seconds. You will hear 3 extra siren chirps indicating shock sensor bypass
for this arming cycle only.

Open Zone Alert / Bypass

Upon arming, this system will warn you if a door is left open. After a 60 second setup delay (for extended
dome lights) has elapsed, if the system detects a fault or a door left open, the siren will chirp 5 times along
with 5 light flashes. This zone will be automatically bypassed and the alarm will protect all other zones.

Pre-Warning Shock Protection

The Pre-warning (warn-away) feature will activate when a low-level shock or vibration detected by the
system’s shock sensor. The alarm will chirp the siren 5 times and flash the lights once to help deter any
further tampering with the vehicle.

Passive Arming Mode: (Programmable)

Passive (automatic) arming occurs 30 seconds after the ignition is turned off and the last door is closed. Upon
closing the last door, the unit will flash the lights twice and LED will be flashing rapidly to confirm passive
countdown. If a door is reopened within the 30 second period, the countdown stop and begin again when the
door is closed. Passive arming provides failsafe protection in case you forget to arm the system.

Passive Locking: (Programmable)

The system can be programmed to passively lock the doors when the system passively arms. The default
setting is OFF because passive locking increases the risk of locking the keys in the vehicle.

Dome Light Illumination (Optional)

This feature will turn on the vehicle’s dome light upon disarming for 30 seconds or until the key is inserted and
turned on. This will provide illuminated entry to your vehicle in dimly lit areas for safety and security.

Trunk/Hatch Pop (Optional, Remote AUX. Output 1) Programmable Option # 8

This feature is designed to interface with existing Factory power trunk or power hatch release systems and
may require additional parts and/or labor charges. Press and release Button #3 (Trunk) on the transmitter to
pop/open the trunk/hatch. If the system is armed, it will also disarm when the button #3 is pressed.

5