Crimestopper SP-200 User Manual

SP-200

REMOTE CONTROL ALARM SYSTEM

OPERATING INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS on your choice of a Remote Alarm System by Crimestopper Security Products Inc. This
booklet contains the information necessary for installing, using, and maintaining your alarm system. If any
questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support
number below.

*IMPORTANT INFORMATION: Primary and Optional Features:

-PRIMARY: These are features that must be connected in order for the system to operate properly; i.e. the

Siren, L.E.D., +12V Power, Ground, Door pin, Flashing lights Override/Program/Valet Button etc.

-OPTIONAL: These are features to be connected if desired or agreed upon by the installing dealer. These
features may also require additional parts and/or labor fees. Consult with your installer beforehand; i.e. Door
Locks, Starter disable, Hood/Trunk trigger, and Auxiliary Remote Outputs etc.

This installation book is designed for the installer or individual with an existing understanding of automotive
electrical systems, along with the ability to test and connect wires for proper operation. To ease installation, we
suggest that you READ THIS MANUAL before beginning your installation. This book is provided as a GENERAL
GUIDLINE and the information contained herein may differ from your vehicle.

TECH SUPPORT

Mon-Fri 8:00 AM-4:30 PM Pacific Time

[phone]

REV. 12-2008

This device complies with FCC Rules part 15. Operation is subject to
the following two conditions: 1) This device may not cause interference,
and (2) this device must accept any interference that may be received,
including interference that may cause undesired operation. The
manufacturer is not responsible for any radio or TV interference caused
by unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.

TABLE OF CONTENTS

Operation Cautions & Warnings……..…………..…………………………………………………………….………2
The Remote Control…..……………………………...……………………..……………………….…….….…..……..3

.

Operating Instructions………………………..……………….…….………………….…….…………...……….…4-7
Car Jack Protection..…………..…………..……………………………………………...…………………..…………8
Transmitter Programming.………………………………….…………………………….……………...…………..…9
2 Vehicle Programming…………..…………..………………….…………………………….…………….……..…..10

Battery Replacement…….…………………………………….....……………………………..……………..…….…11

Data Port Diagram …………………………………………………………………………………………………....…12

OPERATION CAUTIONS & WARNINGS

CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident

resulting from the use of this equipment. This system is designed to be professionally installed into a car or
vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features,
must be in perfect working condition.

DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to repair
and / or replacement charges.

IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system
and its safety features. B) Check for proper operation of these safety features prior to accepting delivery of the
vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all items relative to
the proper operation of this system and its safety features.

DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door
is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death
from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature
of the unit

2

THE REMOTE CONTROL

Selects between Vehicle

Button

Button

Button Options

Functions

Lock Doors & Arm

System

Unlock Doors and

Disarm System

Press and hold 3

Seconds for Panic Mode

Unlock Doors and

Disarm System

Press and Release for

Trunk Release Aux # 1

Trunk Pop (Aux #1)

Press and Release for

Silent Arm / Disarm Aux

Silent Arm. Press and

#2

Hold for Aux #2

LED Blinks while in

Side Button

#1 / Vehicle #2. Press &

Vehicle 2 Mode

Release

3

OPERATION INSTRUCTIONS

ARMING

To arm the alarm and lock the doors, press the Lock button on the transmitter. You will hear a single siren chirp
and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these
optional features are installed. The red LED in the vehicle will start flashing after 5 seconds. After a short delay
to allow vehicle and electronics to stabilize the system will be completely armed.

DISARMING

Press the Unlock button on the transmitter to disarm the alarm. You will hear 2 siren chirps and the lights will
flash twice. The LED stops flashing. Door will unlock and dome light will turn on if the options are installed.

SELECTIVE SILENT ARM/DISARM THROUGH REMOTE CONTROL

This system can be armed and disarmed without siren chirps on an “as needed” basis. Press and release the
Silent Button for arm/disarm without siren chirps.

PROGRAMMABLE SILENT ARM / DISARM MODE (CHIRP DEFEAT)

The system can be silently armed and disarmed as normal with Lock/Unlock Buttons, but no siren chirp. See
alarm programming option (#8) to enable or disable this feature.

PASSIVE ARMING / PASSIVE LOCK MODES / PASSIVE CHIRP COUNTDOWN

If programmed, passive (Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last
door has been closed. The LED will begin flashing rapidly while counting down. If a door or hood is reopened,
the system will wait (LED off) for the door or zone to close before arming. The unit will flash the lights once.
Doors will lock if passive locking is selected. May qualify for insurance discounts-check with your agent or
proprietor. When the Unit is programmed for Passive Chirp Countdown, the siren will chirp during passive
countdown, as an audible warning that arming will occur. This siren will emit a chirp every 2 seconds as soon
as the last door is closed until the system arms 30 seconds later.

REMOTE PANIC PROTECTION

To sound the alarm upon command (panic), press and hold the Lock Button for at least 2 seconds until the siren
sounds. Press the Unlock Button to reset panic mode.

4