How it Works
Crimestopper
Loading...
FS-50
Operator's Manual
20 pgs218.25 Kb0

Crimestopper FS-50 Operator's Manual

SF-50
2-Way LCD Paging Alarm & Remote Engine Starting System
OPERATING INSTRUCTIONS
INTRODUCTION
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These features must be connected in order for the system to operate properly i.e. Power, Ground, LED,
etc.
-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Horn Honk, Dome light illumination, Door Locks, Trunk Pop, etc. These features may require additional parts and labor charges. Consult with your installer about these features BEFORE installation!
CONTACT INFORMATION: TECHNICAL SUPPORT (800)-998-6880 Monday - Friday 8:00am - 4:30pm Pacific
Website: www.crimestopper.com
CRIMESTOPPER SECURITY PRODUCTS, INC. 1770 S. TAPO STREET
This device complies with FCC Rules part 15. Operation is subject to the following two conditions: 1) This device may not cause interference, and (2) this device must accept any interference that may be received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. Such modification could void the user's authority to operate the equipment.
SIMI VALLEY, CA. 93063 REV 12.2008
2
TABLE OF CONTENTS
Operation Cautions & Warnings……..…………..……………………………………………………………………2
The Remote Controls……………….....…………..……………………………………………………………….…3-4
Setting the Clock………………...………………………….…………………………………………………..…...…..4 Quick Chart Button Functions...………………………….…………………………………………………..…...…..5 Operating Instructions - Alarm……………………………………………………….………..……………..……..6-9 Remote Engine Control………………………...……………………………………………….……………..….10-13 Anti-Carjack Protection...……………………………………….………….……..………………..………..………..14 LED and Remote Start Diagnostics………………..……………………………………………….………..….…15
Transceiver / Remote Control Programming……………………………………………………..…………….…16 2 Vehicle Operation……...………………………….……………………………….………….…………….….……17 TURBO Timer Mode…………….……………….…………………………………………………………..……..18-19 Battery Replacement……………….……………………..………….….…………………………………………….20
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident
resulting from the use of this equipment. This system is designed to be professionally installed into a car or vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features, must be in perfect working condition. DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to repair and / or replacement charges. IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system and its safety features. B) Check for proper operation of these safety features prior to accepting delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all items relative to the proper operation of this system and its safety features. DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature of the unit
3
THE REMOTE CONTROLS
2-WAY - PAGER / REMOTE TRANSCEIVER: 1-WAY - SIDEKICK REMOTE:
DISARM / UNLOCK
AM
12:00
PM
START / AUX 2
2nd FUNCTION
ARM / LOCK
2nd FUNCTION
VEH 1 / VEH 2 CLOCK SET
START
VEH 1 / VEH 2
TRUNK
TRUNK
ARM / LOCK
DISARM / UNLOCK
4
THE REMOTE CONTROLS
1-WAY - SIDEKICK REMOTE:
The 1-Way sidekick remote adds flexibility to your system. You can have the convenience of operating your system without needing to carry the larger pager remote. The Sidekick remote has less range and offers all of the same operation features except for page-back confirmation. The 1-Way Sidekick Remote uses two CR­2016 Lithium 3 Volt Batteries.
2-WAY - PAGER / REMOTE TRANSCEIVER: The 2-Way hand-held remote transceiver is used to send and receive information from the vehicle. The
Control Module transmits High Frequency FM signals from the vehicle to your pager over long distances. Your range will vary depending on location, terrain, and local RF noise/interference. This system is not guaranteed to page you if you are behind concrete walls, underground, in a large structure, or in an area with high levels of electronic interference. Handle the pager/remote with care. The LCD display and/or the electronics may be damaged if subjected to abuse. The AAA Cell 1.5V alkaline battery can easily be replaced by sliding open the battery access door on the back of the remote. Battery life will vary depending on usage. The LCD screen will display a low battery icon when the battery is low.
SETTING THE CLOCK (2-WAY- LCD REMOTE)
1. Press VEH Button on the side of the remote control 5 times.
2. The remote will beep and the AM or PM display will begin flashing.
3. Press the Trunk Button to go to the next item – AM - PM - Hour- Minutes.
4. Press the Lock Button to increase time.
5. Press the Unlock Button to decrease time.
6. Press the Start Button to Disable or Enable Beep.
7. Press the VEH Button to Exit Setup or wait 7 seconds, the LCD light will turn off.
5
QUICK CHART BUTTON FUNCTIONS
Press and Hold for 2
Press and Hold for 2
for Trunk Pop Aux #1
Seconds for CarJack
Momentary, Timed or
Momentary, Timed or
Button
Then
Then
Button
Functions
Lock Doors & Arm
System
Unlock Doors &
Disarm System
Trunk Pop
Start or Stop engine
Activates
Activates
Aux # 1
Aux #2
Aux #3
Button Options Button
Press and Hold 2
Seconds for Panic
Mode
Press twice for
second door unlock
Press and Release
Press for Remote
Start. Three options
available
Steady Momentary
Output
Latched Output
VEH
Plus
Plus
Plus
Button
Functions
2nd Function
Selects between
Vehicle #1 and
Vehicle #2
Valet Service / Park
Sensor ON / Off
Activates CarJack
with Ignition On
Activates
Activates
Aux #2
Aux #3
Button Options
seconds
seconds
Valet Mode when
Disarmed. Sensor
On/Off when Armed
Press and Hold 2
Mode
Steady Momentary
Output
Momentary, Timed
or Latched Output
Then
Then
CLOCK SETUP:
No Arm / Disarm
No Function No Function Silent Arm / Disarm
Activates
Lock = Increase, Unlock = Decrease, Trunk = Next, Start = Beep with button press, VEH = Exit
Aux #4
Latched Output
Plus
Plus
Activates
Aux #4
Chrip from Siren or
Momentary, Timed
or Latched Output
Horn
6
OPERATING INSTRUCTIONS - ALARM
Arming / Locking:
Press the Lock Button on the remote control. The System will arm emit one siren chirp, one light flash, and the LED will begin to flash. Power locks will lock (if equipped). Starter disable circuit will turn on. The 2-Way LCD Pager will beep once while displaying a Locking symbol. After a short delay to allow the vehicle and electronics to settle, the system will be completely armed.
Disarming: / Unlocking
Press the Unlock Button on the remote control. The System will disarm and confirm with two siren chirps, two light flashes, and the LED will turn off. Power locks will unlock and Interior Dome light will turn on (if installed with these optional features). The 2-Way LCD Pager will beep twice while displaying an Unlock symbol.
Alarm Triggers:
If there is an intrusion into the vehicle, a hard impact to the body or the ignition is turned on, the alarm will sound and flash the lights for 1 minute. After 1 minute, the trigger cycle will automatically stop and alarm will remain armed to continue protecting the vehicle. If a door is left open after an intrusion then the unit will cycle a maximum of 2 minutes and continue to protect the other un-tampered or unopened zones.
LCD Remote Paging / Zone Violations:
When the system is triggered, the alarm sends a paging signal to the remote. If you are within range, you will receive a paging signal that will light up the LCD Screen Red. The display will show an icon of what caused the violation. The paging remote will also vibrate and beep to notify you the vehicle has been tampered with.
Disarming While Tripped (Triggered):
Disarming the System while it is triggering requires TWO presses of the Unlock Button. The first press Resets the alarm cycle only (system still armed) while a second press will disarm/unlock the system.
Selective Silent Arming / Disarming:
To Arm or Disarm the system without siren chirps, press and release both the Unlock and Start Button at the same time. The System will Arm or Disarm without siren chirps. Flashing lights and LED will be the only indicators of Arm/Disarm status. The LCD will Display a musical note with an “Ø” when the system is armed or disarmed without a chirp
Loading...
+ 14 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use