Crimestopper CS-5601 Installation Manual

CS-5601

4 WINDOW CONTROL MODULE

INSTALLATION & OPERATING INSTRUCTIONS

INTRODUCTION:

CONGRATULATIONS on your choice of a 4 Window Control Module by Crimestopper Security Products Inc.
This booklet contains the information necessary for installing, and operating your system. If any questions
arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number
below.

*IMPORTANT INFORMATION:
This system does not affect the operation of the factory power window switches. This is an ADD-ON

module to an Alarm, Remote Start, or Keyless Entry system. It is designed for medium to high current
window motors. It can roll 4 windows UP or DOWN, or 2 windows UP and DOWN. Each window circuit
activates in sequence, one at a time. This minimizes the current draw on the vehicle battery.

This installation book is designed for the installer or individual with an existing understanding of automotive
electrical systems, along with the ability to test and connect wires for proper operation. To ease installation,
we suggest that you READ THIS MANUAL before beginning your installation. The information contained in
this manual is provided as a GENERAL GUIDLINE and it may differ from your vehicle! If you are not confident
with performing the installation steps as required by this system, we suggest seeking professional installation.

TECH SUPPORT

Mon-Fri 8:00 AM -4:30 PM Pacific Time

[phone]

REV - 9/3/2004

TABLE OF CONTENTS

2

• Pre-Installation & Component Mounting……… ………..…….……………………………………………2-3

• Wiring …… ……..………………………………………………………………………………………….…….3-4

• 4 Window s UP. …..………………………………………….……………….………..……………….…..……..5

• 2 Windows UP and DOWN..………………….…………………………………………………………………6

• Vehicles with Normally Open Power w indows……………..………….……………………………………7

• Testing and Adjusting Window Shut Off Current …………………..………………………………………8

PRE-INSTALLATION CONSIDERATIONS

To ease installation, we suggest that you READ THIS MANUAL before beginning your installation.

BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR
BAGS, ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY).

PLAN OUT YOUR INSTALLATION and determine most suitable locations for all components to be placed.
These components include: the module itself, valet/program button and possible relays. Allow enough wire to
create a service loop with strain relief, should servicing be required.

DAMAGE resulting from incorrect installation or failure to follow guidelines stated in this book will not be
covered under warranty and subject to repair or replacement charges.

USE A VOLT/OHM METER to test and locate all connections. Test Lights can damage a vehicle’s computer
systems.

ADDITIONAL PARTS, extra relays (Part #CS-402A) for converting normally open or normally powered
window switches to normally grounded.

DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering
column, or any other moving parts in the vehicle.

REMOVE MAIN SYSTEM FUSE (S) before jump starting the vehicl e or charging the vehicles battery.

COMPONENT MOUNTING

CONTROL MODULE: Locate the module under dash as high as possible, away from moving parts . Driver’s

Side usually provides an easy location for the majority of the wiring connections.

WARNING: Module isn’t water proof. Don’t Install CS-5601 Module inside vehicle door.

If the module gets water damaged, the vehicle windows could stop working.

WIRING

8 Position Connector Plug – Small Wires

1 - GRAY: Negative roll trigger for Circuit #1 and #2.

Circuit #1 and #2 are controlled by LOOP 1 - USE ONLY ONE.

2 - GRAY/WHITE: Positive roll trigger for Circuit #1 and #2.
3 - BLACK: SYSTEM CHASSIS GROUND: This wire must be connected to chassis metal of vehicle.

Scrape away any paint or dirt from the connection poi nt to ensure a good connection.

4 - GREEN: (-) 300 milliamps Negative output though out operation of any 4 circuits
5 - YELLOW: (+) 300 milliam ps Positive output through out operation of any 4 circuits

6 - BLUE: Negative roll trigger for Circuit #3 and #4.

Circuit #3 and #4 are controlled by LOOP 2 - USE ONLY ONE.

7 - BLUE/RED: Positive roll trigger for Circuit #3 and #4.
8 - PINK: Connect to an ignition wire that shows +12 Volts when the key in both “On” and “Start” positions.

This wire prevents the module from activating the windows while driving the vehicle.

3