CrimeStopper CS-2014TW2 Operation Instructions Manual
CS-2014TW2 Super Page V™
2-Way AM/FM LCD Paging Alarm & Remote Engine Starting System
OPERATION INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of the SuperPage V™ by Crimestopper Security Products Inc. This booklet
contains the information necessary for operating your system. If any questions arise, contact your installation dealer or
Crimestopper Security Products Inc.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These features must be connected in order for the system to operate properly i.e. Power, Ground, LED,
etc.
-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Horn Honk,
Dome light illumination, Door Locks, Trunk Pop, etc. These features may require additional parts and labor charges.
Consult with your installer about these features BEFORE installation!
CONTACT INFORMATION:
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific
Website: www.crimestopper.com
E-mail: tech-support@crimestopper.com
CRIMESTOPPER
SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063 REV. A1 02.01.2005
This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: 1) This device may not cause
interference, and (2) this device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modification to this
equipment. Such modification could void the user's authority to
operate the equipment.
TABLE OF CONTENTS
Operation Cautions & Warnings……..…………..……………………………………………………………………2
Transceiver / Pager-Remote……….....…………..……………………………………………………………………3
CS-416TW Sidekick Remote Control…………………….…………………………………………………..…...…..4
Operating Instructions - Alarm……………………………………………………….………..……………..……..5-8
Remote Engine Control………………………...……………………………………………….…….………...….9-12
Anti-Carjack Protection...……………………………………….………….……..………………..………..………..13
LED Diagnostics………………..……………………………………………………………………….………..….…14
Transceiver / Remote Control Programming……………………………………………………..……………14-15
2 Vehicle Operation……...………………………….……………………………….………….…………….….……16
Troubleshooting / FAQ Section……………….…………………………………………………………..……..17-18
Low Battery Warning – LCD Remote / Setting Clock – LCD Remote……………………………….….……..19
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident
resulting from the use of this equipment. This system is designed to be professionally installed into a car or
vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features,
must be in perfect working condition.
DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to
repair and / or replacement charges.
IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this
system and its safety features. B) Check for proper operation of these safety features prior to accepting
delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all
items relative to the proper operation of this system and its safety features.
DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door
is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death
from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature
of the unit
2
#2 DISARM
UNLOCK
LCD
SCREEN
#4 ENGINE
START/STOP
#1 ARM
LOCK
#3 TRUNK
#5 RECALL
CAR I or II
FIXED
ANTENNA
AM
BUTTON 5
(On side of remote):
• Press and release to light up
the LCD screen.
• Press and release twice to
recall the last message from
the LCD screen.
• Press and Hold two seconds
to change from Car 1 to Car 2
• Press 5 times to change the
Time and audible beep tones
on the remote.
TRANSCEIVER / PAGER-REMOTE
PAGER / REMOTE TRANSCEIVER:
The hand-held remote transceiver is used to send and
receive information from the vehicle. The Control Module
transmits High Frequency AM/FM signals from the vehicle
to your over long distances. Your range will vary depending
on location, terrain, and local RF noise/interference. This
system is not guaranteed to page you if you are behind
concrete walls, underground, in a large structure, or in an
area with high levels of electronic interference. Handle the
pager/remote with care if the LCD display and/or the
electronics may be damaged if subjected to abuse. The
AAA Cell 1.5V alkaline battery can easily be replaced by
sliding open the battery access door on the back of the
remote. Battery life will vary depending on usage. The
LCD screen will display a low battery icon when the battery
is low. For more see “Range Questions” on page 17.
BUTTON 1(Lock Symbol):
• Press and release to Arm/Lock system.
• Press and Hold for more than 3 seconds to activate “Panic” feature.
BUTTON 2 (Unlock Symbol):
• Press and release to Disarm/Unlock system, or reset a cycle.
BUTTON 3 (Trunk Symbol):
• Press and Release to activate trunk pop (Auxiliary output #1) Optional
Feature.
• Press and Hold to activate a second optional feature (Auxiliary output
#2).
BUTTON 4 (Start Key Symbol):
• Press and release to Start/Stop engine.
CrimeStopper
#3
#1
#2
#4
LOCK/
TRUNK
REMOTE
UNLOCK/
VEHICLE 2
FLASHLIGHT
START
#5
#6
ARM
DISARM
CS-416TW SIDEKICK REMOTE
The CS-416TW 1-Way sidekick remote adds flexibility to your CS-2014TW2. You can have the convenience
of operating your system without needing to carry
the larger pager remote. The Sidekick remote has
less range and offers all of the same operation
features except for page-back confirmation.
BUTTON 1(Lock Symbol):
• Press and release to Arm/Lock system.
• Press and Hold for more than 3 seconds to
activate “Panic” feature.
BUTTON 2 (Unlock Symbol):
• Press and release to Disarm/Unlock system, or
reset a cycle.
BUTTON 3 (Trunk Symbol):
• Press and Release to activate trunk pop
(Auxiliary output #1) Optional Feature.
• Press and Hold to activate a second optional
feature (Auxiliary output #2).
BUTTON 4 (Start Key Symbol):
• Press and release to Start/Stop engine.
BUTTON 5 (Upper side button of remote):
• Press for convenient flashlight function. The high-power LED acts as a mini flashlight.
BUTTON 6 (Lower side button of remote):
• Press and release to activate Vehicle #2 mode. (Led will flash for 4 second to use vehicle #2, otherwise
remote will revert back to Vehicle #1
4
ARM-LOCK
OPERATING INSTRUCTIONS - ALARM
Active Arming / Locking:
Press button #1 (Lock symbol) on the transceiver. The System will arm emit one siren chirp,
one light flash, and the LED will begin to flash. Power locks will lock (if equipped). Starter
disable circuit will turn on. LCD Pager will beep once while displaying a Locking symbol. After
a short delay to allow the vehicle and electronics to settle, the system will be completely
armed.
Disarming: / Unlocking
Press button #2 (Unlock symbol) on the transceiver. System will disarm and confirm with two
siren chirps, two light flashes, and the LED will turn off. Power locks will unlock and Interior
Dome light will turn on (if installed with these optional features). LCD Pager will beep twice
while displaying an Unlock symbol.
Alarm Triggers:
If there is an intrusion into the vehicle, a hard impact to the body or the ignition is turned on,
the alarm will sound and flash the lights for 1 minute. After 1 minute, the trigger cycle will
automatically stop and alarm will remain armed to continue protecting the vehicle. If a door is
left open after an intrusion then the unit will cycle a maximum of 2 minutes and continue to
protect the other un-tampered or unopened zones.
LCD Remote Paging / Zone Violations:
When the system is triggered, the alarm sends a paging signal to the remote. If you are within
range, you will receive a violation paging signal that consists of a vibration followed by 15
audible beeps to notify you the vehicle has been tampered with.
5
SHOCK SENSOR
DOOR TRIGGER
IGNITION TRIGGER
HOOD/TRUNK
TRIGGER
DISARM
-
UNLOCK
SILENT ARM
SILENT DIS
ARM
PANIC MODE
All Icons Flash
OPERATING INSTRUCTIONS - ALARM
Disarming While Tripped (Triggered):
Disarming the System while it is triggering requires TWO presses of the #2 Unlock Button. The first press of
Button #2 Resets the alarm cycle only (system still armed) while a second press will disarm/unlock the system.
Selective Silent Arming/Disarming:
To Arm or Disarm the system without siren chirps, press and
release both Buttons #2 (Unlock) and #4 (Start) at the same time.
System will Arm or Disarm without siren chirps. Flashing lights and
LED will be the only indicators of Arm/Disarm status. The LCD will
Display a musical note with an “X” when the system is armed or
disarmed without a chirp
Prior intrusion Alert
This system will notify you if the alarm was triggered while you where away. Upon disarming, there will be four
additional siren chirps after the two normal disarm chirps. Check your vehicle for any signs of a break in or
tampering. Also, see LED Diagnostics Section to determine the cause of the trigger.
Remote Panic Protection
To sound the alarm in an emergency situation or to draw attention to your vehicle, press
and hold Button #1 (Lock) for at least 3 seconds until the siren sounds. Press Button #2
(Unlock) to reset panic mode. The LCD display will flash all the icons and emit 15 beeps
when the panic mode is triggered.
Selective Shock Sensor Disable
To arm the alarm and bypass shock sensor protection, press Button #1 as normal then
press and release Button #1 and #2 together within 2 seconds. You will hear 3 extra
siren chirps indicating shock sensor bypass for this arming cycle only. This feature useful
when parking near railroad tracks, airports, or area with excessive loud machinery or
noise to prevent the nuisance of unnecessary false alarms.
Open Door Alert / Bypass
Upon arming, this system will warn you if a door is left open. The LCD pager will vibrate and beep (15X’s)
along with displaying the open zone on your LCD screen. This zone will automatically be bypassed until
closed; otherwise, the alarm will continue to protect all other zones.
Loading...