Crimestopper CS-2011RS User Manual

t
t
V

CS-2011RS Series IV

Super Rage™

Remote Control Alarm & Remote Engine Starting System

OPERATION INSTRUCTIONS

INTRODUCTION
questions arise, contact your installation dealer or Crimestopper Security Products Inc.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Power,
Ground, Lights, Siren, etc.
-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Door Locks, Horn Honk, Dome light illumination, Starter Kill, L.E.D., Trunk Pop, etc. These features may require additional parts and labor charges. Consult with your installer about these features before installation.
CONTACT INFORMATION: TECHNICAL SUPPORT (800)-998-6880 Monday - Friday 8:00am - 4:30pm Pacific
Website: www.crimestopper.com E-mail: tech-support@crimestopper.com
CRIMESTOPPER SECURITY PRODUCTS, INC. 1770 S. TAPO STREET SIMI VALLEY, CA. 93063
REV. B 03.2004
This device complies with FCC Rules part 15. Operation is subjec to the following two conditions: 1) This device may not cause interference, and (2) this device must accept any interference tha may be received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or T interference caused by unauthorized modification to this equipment. Such modification could void the user's authority to operate the equipment.
TABLE OF CONTENTS
Operation Cautions & Warnings……..………..…………………………………………………………….………2
Operating Instructions - Alarm……………………………………………………….………..……………..……..3-6
LED Diagnostics………………..…………………………………………………………………….………..…..….6
Remote Engine Control………………………...…………………………………………………….………...…..6-10
Optional Turbo Timer Mode……………………...…………………………………………………………..…..….11
Anti-Carjack Protection...……………………………………….………….……..…………...…………..……...…12
Transmitter Programming……………………………….……………………………………………..………….…13
2 Vehicle Operation……...………………………….……………………………….………….……………...……14
Troubleshooting: “Before you call section”……………………………………………………………………..….15
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident
resulting from the use of this equipment. This system is designed to be professionally installed into a car or vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features, must be in perfect working condition.
DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to repair and / or replacement charges.
IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system and its safety features. B) Check for proper operation of these safety features prior to accepting delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all items relative to the proper operation of this system and its safety features.
DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature of the unit
2
OPERATING INSTRUCTIONS - ALARM
Active Arming / Locking:
Press and release button #1 (Lock symbol) on the transmitter. The System will arm and confirm with one siren chirp, one light flash, and the LED will begin to flash. Power locks will lock (if equipped). Starter disable circuit will turn on. After a short delay to allow the vehicle and electronics to settle, the system is completely armed.
Disarming: / Unlocking Press and release button #2 (Unlock symbol) on the transmitter. System will disarm and confirm with two siren chirps, two light
#1
LOCK/
ARM
#3
TRUNK
FLASHLIGHT
START
VEHICLE 2
CrimeStopper
flashes, and the LED will turn off. Power locks will Unlock and Interior Dome light will turn on (if installed with these optional features)
Disarming While Tripped (Triggered):
Disarming the System while it is triggering requires TWO presses of the #2 Unlock Button. The first press of Button #2 Resets the alarm cycle only (system still armed) while a second press will disarm/unlock the system.
Silent Arming/Disarming (On demand):
To Arm or Disarm the system without siren chirps, press and release both Buttons #2 (Unlock) and #4 (Start) at the same time. System will Arm or Disarm without siren chirps that one time. Flashing lights and LED will be the only indicators of Arm/Disarm status. If the system was tripped while you were way, 4 chirps will be heard to notify you that the system was tripped.
Silent Arming/Disarming (Chirp Defeat):
This system can be programmed to silent arm and disarm using the normal lock and unlock buttons. Flashing lights and LED will be the only indicators of armed or disarm status. Check with your installer or follow programming option instructions in the installation manual.
Alarm Triggering
An intrusion into the vehicle or hard impact to the body will sound the alarm and flash the lights for 1 minute. After 1 minute the trigger cycle will automatically stop and alarm will remain armed to continue protecting the vehicle. If a door is left open after an intrusion then the unit will cycle a maximum of 5 minutes and continue to protect the other un-tampered or unopened zones.
3
#2
UNLOCK/
DISARM
#5
#6
#4
REMOTE
START
OPERATING INSTRUCTIONS - ALARM
Prior intrusion Alert
This system will notify you if the alarm was tripped while you where away. Upon disarming, the two normal disarm chirps will be heard then the system will emit 4 additional siren chirps. Check your vehicle for any signs of a break in or tampering. Also see LED Diagnostics Section to determine the cause of the trigger.
Remote Panic Protection
To sound the alarm in an emergency situation or to draw attention to your vehicle, press and hold Button #1 (Lock) for at least 3 seconds until the siren sounds. Press Button #2 (Unlock) to reset panic mode.

Arming With Shock Sensor Bypass

To arm the alarm and bypass shock sensor protection, press Button #1 as normal then press and release Button #1 and #2 together within 2 seconds. You will hear 3 extra siren chirps indicating shock sensor bypass for this arming cycle only.
Open Zone Alert / Bypass
Upon arming, this system will warn you if a door is left open. After a 60 second setup delay (for extended dome lights) has elapsed, if the system detects a fault or a door left open, the siren will chirp 5 times along with 5 light flashes. This zone will be automatically bypassed and the alarm will protect all other zones.
Pre-Warning Shock Protection
The Pre-warning (warn-away) feature will activate when a low-level shock or vibration detected by the system’s shock sensor. The alarm will chirp the siren 5 times and flash the lights once to help deter any further tampering with the vehicle.
Passive Arming Mode: (Programmable)
Passive (automatic) arming occurs 30 seconds after the ignition is turned off and the last door is closed. Upon closing the last door, the unit will flash the lights twice and LED will be flashing rapidly to confirm passive countdown. If a door is reopened within the 30 second period, the countdown stop and begin again when the door is closed. Passive arming provides failsafe protection in case you forget to arm the system.
Passive Locking: (Programmable)
The CS2011RS system can be programmed to passively lock the doors when the system passively arms. The default setting is OFF because passive locking increases the risk of locking the keys in the vehicle.
Trunk/Hatch Pop (Optional, Remote AUX. Output 1)
This feature is designed to interface with existing Factory power trunk or power hatch release systems and may require additional parts and/or labor charges. Press and release Button #3 (Trunk) on the transmitter to
4
pop/open the trunk/hatch. If the system is armed, it will also disarm when the button #3 is pressed.
OPERATING INSTRUCTIONS - ALARM
Remote AUX. Output 2 (Optional)
This system contains a second auxiliary output to activate other accessories or devices. To activate the systems’ Second Auxiliary Output, press and hold Button #3 (Trunk Symbol) on the transmitter for more than 2 seconds. This is a momentary output that will stay active as long as the remote button is held down. Remote output #2 requires programming before operation. Check with your installer or follow programming option instructions in the installation manual.
Dome Light Illumination (Optional)
This feature will turn on the vehicle’s dome light upon disarming for 30 seconds or until the key is inserted and turned on. This will provide illuminated entry to your vehicle in dimly lit areas for safety and security.
Emergency Override (Disarm)
If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to disarm the system manually. Open the door with the key [alarm will sound], turn the ignition on, and press the override/program button for about 5 seconds. The Alarm will disarm and allow you to use the vehicle until you can repair/replace the remote. Note that you may need to put the system into valet mode to prevent passive arming.
Valet Mode (Enter manually or using the remote)
To disable Alarm and Remote Engine Starting for vehicle servicing or otherwise, turn the ignition on and press the override/program button [about 5-7 seconds] until you hear (3) siren chirps and the LED turns on solid. Repeat the process to exit VALET mode. To enter / exit valet via the remote, press and hold both buttons #1 (Lock) and Button #2 (unlock) together for about 3 seconds until 3 chirps are heard. Repeat this step to exit via the remote transmitter. Lock/Unlock and AUX features will still operate in when in VALET mode however remote start and alarm functions are inhibited.
Valet Park Mode (Using the remote transmitter only)
Note: Valet Park mode is only accessible when using the remote transmitter. Valet park mode allows you to turn over the vehicle to a valet allowing access to drive/lock/unlock your vehicle, but alarm will trigger if the trunk is opened. To activate Valet Park, press and hold both buttons #1 (Lock) and Button #2 (unlock) together for about 6 seconds. 3 chirps will be heard first when unit goes into regular Valet and as you continue to hold both buttons you will hear 2 more chirps. LED will flash slowly when in Valet Park. Repeat step to exit Valet Park mode.
5
Loading...
+ 11 hidden pages