Crimestopper CS-2011.II Operator's Manual

This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: 1) This device may not cause

is device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modification to this

cation could void the user's authority to

CS-2011RS Series II

Super Rage™

Remote Control Alarm & Remote Engine Starting System

OPERATION INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS on your choice of a Super Rage™ Alarm & Remote Engine Starter by Crimestopper Security
Products Inc. This booklet contains the information necessary for operating your system. If any questions arise,

contact your installation dealer or Crimestopper Security Products Inc.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Power,

Ground, Lights, Power Locks, etc.

-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Horn Honk,
Dome light illumination, Starter Kill, L.E.D., Trunk Pop, etc. These features may require additional parts and labor
charges. Consult with your installer about these features before installation.

CONTACT INFORMATION:
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific

Website: www.crimestopper.com
E-mail: [e-mail]

CRIMESTOPPER
SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063 REV. B 06.2001

interference, and (2) th

equipment. Such modifi
operate the equipment.

TABLE OF CONTENTS

Operation Cautions & Warnings……..…………..……………………………………………………………………2
Operating Instructions - Alarm……………………………………………………….………..……………..……..3-5
LED Diagnostics………………..……………………………………………………………………….………..…..….6
Remote Engine Control………………………...…………………………………………………….………...…….6-9
Anti-Carjack Protection...……………………………………….………….……..…………...…………..…….…9-10
Transmitter Programming……………………………….……………………………………………..…………10-11
2 Vehicle Operation……...………………………….……………………………….………….…………….….……11
Troubleshooting: “Before you call section”………………………………………………………………...…….12

OPERATION CAUTIONS & WARNINGS

CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident

resulting from the use of this equipment. This system is designed to be professionally installed into a car or
vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features,
must be in perfect working condition.

DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to
repair and / or replacement charges.

IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this
system and its safety features. B) Check for proper operation of these safety features prior to accepting
delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all
items relative to the proper operation of this system and its safety features.

DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door
is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death
from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature
of the unit

OPERATING INSTRUCTIONS - ALARM

Active Arming / Locking:

Press button #1 (Lock symbol) on the transmitter. The System will arm
and confirm with one siren chirp, one light flash, and the LED will begin
to flash. Power locks will lock (if equipped). Starter disable circuit will
turn on. After a short delay to allow the vehicle and electronics to settle,
the system will be completely armed.

Disarming: / Unlocking
Press button #2 (Unlock symbol) on the transmitter. System will disarm

#1

LOCK/

ARM

#3

AUX 1,2

C

RIMESTOPPER

START

and confirm with two siren chirps, two light flashes, and the LED will
turn off. Power locks will Unlock and Interior Dome light will turn on (if

CS2011RS TRANSMITTER

installed with these optional features)

Disarming While Tripped (Triggered):

Disarming the System while it is triggering requires TWO presses of the #2 Unlock Button. The first press of
Button #2 Resets the alarm cycle only (system still armed) while a second press will disarm/unlock the system.

Silent Arming/Disarming:

To Arm or Disarm the system without siren chirps, press and release both Buttons #2 (Unlock) and #4 (Start)
at the same time. System will Arm or Disarm without siren chirps. Flashing lights and LED will be the only
indicators of Arm/Disarm status. If the system was tripped while you were way, 4 chirps will be heard to notify
you that the system was tripped.

Alarm Triggering

An intrusion into the vehicle or hard impact to the body will sound the alarm and flash the lights for 1 minute.
After 1 minute the trigger cycle will automatically stop and alarm will remain armed to continue protecting the
vehicle. If a door is left open after an intrusion then the unit will cycle a maximum of 5 minutes and continue to
protect the other un-tampered or unopened zones.

Prior intrusion Alert

This system will notify you if the alarm was tripped while you where away. Upon disarming, the two normal
disarm chirps will be heard then the system will emit 4 additional siren chirps. Check your vehicle for any
signs of a break in or tampering. Also see LED Diagnostics Section to determine the cause of the trigger.

Remote Panic Protection

To sound the alarm in an emergency situation or to draw attention to your vehicle, press and hold Button #1
(Lock) for at least 3 seconds until the siren sounds. Press Button #2 (Unlock) to reset panic mode.

#2

UNLOCK/

DISARM

#4

ENGINE

START/STOP

OPERATING INSTRUCTIONS - ALARM

Arming With Shock Sensor Bypass

To arm the alarm and bypass shock sensor protection, press Button #1 as normal then press and release
Button #1 and #2 together within 2 seconds. You will hear 3 extra siren chirps indicating shock sensor bypass
for this arming cycle only.

Open Door Alert / Bypass

Upon arming, this system will warn you if a door is left open. After a 60 second setup delay (for extended
dome lights) has elapsed, if the system detects a fault or a door left open, the siren will chirp 5 times along
with 5 light flashes. This zone will be automatically bypassed and the alarm will continue to protect all other
zones.

Pre-Warning Shock Protection

The Pre-warning (warn-away) feature will activate when a low-level shock or vibration detected by the
system’s shock sensor. The alarm will chirp the siren 5 times and flash the lights once to help deter any
further tampering with the vehicle.

Passive Arming Mode: (Programmable)

Passive (automatic) arming occurs 30 seconds after the ignition is turned off and the last door is closed. Upon
closing the last door, the unit will flash the lights twice and LED will be flashing rapidly to confirm passive
countdown. If a door is reopened within the 30 second period, the countdown stop and begin again when the
door is closed. Passive arming provides failsafe protection in case you forget to arm the system.

Passive Locking: (Programmable)

The CS2011RS system can be programmed to passively lock the doors when the system passively arms.
The default setting is OFF because passive locking increases the risk of locking the keys in the vehicle.

Trunk/Hatch Pop (Optional, Remote AUX. Output 1)

This feature is designed to interface with existing Factory power trunk or power hatch release systems and
may require additional parts and/or labor charges. Press and release Button #3 (Trunk) on the transmitter to
pop/open the trunk/hatch. If the system is armed, it will also disarm when the button #3 is pressed.

Remote AUX. Output 2 (Optional)

This system contains a second auxiliary output to activate other accessories or devices. To activate the
systems’ Second Auxiliary Output, press and hold Button #3 (Trunk Symbol) on the transmitter for more than 2
seconds. This is a momentary output that will stay active as long as the remote button is held down.