CrimeStopper CS-2000DPII .IV Installation & Operating Instructions Manual

CS-2000DPII Series IV
REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of an On-Guard Series Remote Alarm System with Data Port Technology by Crimestopper Security Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.
IMPORTANT INFORMATION: Primary and Optional Features:
-PRIMARY: These are features that must be connected in order for the system to operate properly; i.e. the
Siren, L.E.D., 12V Power, Ground, Door pin, Flashing Lights and Override Program Valet Button etc.
-OPTIONAL: These are features to be connected if desired or agreed upon by the installing dealer. These features may also require additional parts and/or labor fees. Consult with your installer beforehand; i.e. Door Locks, Flashing Lights, Starter disable, Hood Trunk trigger, and Auxiliary Remote Outputs etc.
This installation book is designed for the installer or individual with an existing understanding of automotive electrical systems, along with the ability to test and connect wires for proper operation. To ease installation, we suggest that you READ THIS MANUAL before beginning your installation. This book is provided as a GENERAL GUIDLINE and the information contained herein may differ from your vehicle.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
REV. D 1.2007
This device complies with FCC Rules part 15. Operation is subject to the following two conditions: 1) This device may not cause interference, and (2) this device must accept any interference that may be received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. Such modification could void the user's authority to operate the equipment.
TABLE OF CONTENTS
Installation Cautions & Warnings…….………………………………………………………….………………2 Control Module & Component Mounting…………….………………………..………………..….…………..3 Wiring……..…………………………………………………………………………………………………….…….4-5 Power Door Lock Wiring...…………………………………………………….………..…………………………6 Transmitter Programming…………………………………………………………………………………………7 Option Programming………………………………………….………………………………..………………….8-11 Operating Instructions………………………..……………………………………………………..……..…….12-15 Car Jack Protection…………………………………………………………….……………………..……………16 System Wiring Diagram………………………………………………………………………………..….………17 2 Vehicle Operation……………………………………………………………………………………..….………18 DATA PORT Diagram………………………………………………………………………………..….……….…19
INSTALLATION CAUTIONS & WARNINGS
BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR
BAGS, ABS BRAKES, ENGINE COMPUTERS, BATTERY etc.). WE RECOMMEND the use of a VOLT/OHM METER to test and verify wiring circuits. Test lights or illuminated
probes can cause damage to on-board computer or engine management systems. DO NOT exceed maximum output ratings or damage may occur. Electrical current limits for this alarm are
listed where applicable on the system diagram (Pg. 17). If you are unsure about the current load, of a specific circuit on your vehicle, measure the load first with an amp-meter before connecting.
WE RECOMMEND that the MAIN SYSTEM FUSE be REMOVED before jump starting, using a battery charger, or changing the battery. A voltage surge or high boost condition could damage alarm circuits.
DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering column, or any other moving parts in the vehicle.
CONTROL MODULE MOUNTING
DO NOT Mount the control unit in the engine compartment! DO NOT Mount the control unit or wiring harness where they can become entangled with moving parts
such as brake/gas/clutch pedals, or the steering colum n!
The alarm control module should be mounted in a concealed location. The Placement of the module will affect the distance from which the remote transmitter can control the unit. The antenna wire should be routed away from any metal if possible. Do not alter the length of the antenna wire or route it with other wires. Do not ground the antenna wire. Fasten the module to a bracket or wire harness using the cable ties provided.
Underdash Mounting: If you are locating the control unit underdash, mount it as high as possible, not easily located by an intruder.
Driver’s Side Underdash mounting provides an easy location for wiring most of the system’s connections, however this is a common location for an intruder to check for an alarm after breaking into the vehicle. The left side of the vehicle may contain more metal and or wiring that will create interference and decrease the operating range of the system.
Passenger Side underdash is a good location, however some extra wiring may be needed to extend wires across from the driver’s side. Under-seat / Center Console mounting is also a possibility, but NOT RECOMMENDED. The system’s transmitter range will be reduced by the metal structures of the seat or center console and the unit may also be exposed to moisture from spilled drinks etc. Moisture or water damage is not covered under the warranty and will be subject to repair charges. Under seat or console mounting will create more difficulty if you need to access the unit for service or want to add-on features or connections later. Use this location as a last resort.
COMPONENT MOUNTING
SIREN: Mount the siren under the hood to an inner fender-well or other body surface with the open end facing
downward.
LED: Mount the LED status indicator in a visible location on the dashboard or console. Shock Sensor: Mount the included shock sensor with wire ties to an under dash wire harness or fasten with
screws to firewall or side paneling. Use the adjustment screw to set the sensitivity of the sensor. Valet Override Program Button: Mount the Valet/Override/Program push-button in a hidden but accessible
location. It is REQUIRED for emergency disarm, programming, and valet mode.
WIRING
GREEN WIRE: (-) DOOR TRIGGER
Identify the wire that reads ground when any door is open and 12 volts when all doors are closed. Some vehicles may have isolated door triggers. In this case you may need to run additional wires from other doors or go directly to the wire that triggers the vehicle’s interior dome light. One vehicle will not require the use of BOTH door trigger wires.
VIOLET WIRE: (+) DOOR TRIGGER
Same as the GREEN wire above except this wire is used for vehicles that show a positive voltage (12 volts) when the door is open and a ground when doors are closed as in many Ford, Lincoln, and Mercury vehicles.
BLACK WIRE: SYSTEM CHASSIS GROUND
The Black wire MUST be connected the CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection. Keep the ground wire short.
YELLOW WIRE: IGNITION SWITCHED “ ON ” AND “ START ” 12 VOLTS
Connect to an IGNITION wire (or fuse in the fuse box) that shows 12 Volts when the key in both “ On ” and “ Start ” (WHEN CRANKING) positions.
GRAY WIRE: (-) AUX REMOTE OUTPUT 1 (Optional, may require a relay) Connect to the Negative trunk release circuit or to the activation circuit of an auxiliary module or device. If the circuit requires 12V, then a relay is required. RELAY WIRING: Connect the Gray wire to terminal 85, connect relay terminals 86 and 87 to 12V constant power. Connect terminal 30 of the relay to the 12V positive device/circuit to be activated.
BLUE WIRE: (-) HOOD/TRUNK TRIGGER (Optional)
Input trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk pin switches that read ground when open. If no existing switches are available, install new pin switches if desired. Note: DO NOT mount new pin switches in water pathways.
BLACK WHITE WIRE: (-) DOME LIGHT ILLUMINATION OUTPUT (Optional, requires a relay)
Connect Black/White wire to terminal #85 of a relay. (Relay not included) Connect terminal #86 of relay to 12 Volt Constant power. For POSITIVE dome light circuits, connect Terminal #87 to fused +12V Constant. For NEGATIVE Dome light circuits, connect terminal #87 to chassis ground. Connect terminal of the #30 of the relay to the dome light activation circuit in the vehicle.
WIRING
BROWN WHITE WIRE: (-) HORN PULSE / CHIRP OUTPUT (Optional, may require a relay)
Connect to the Negative Horn Trigger wire usually located near the steering column. If the vehicle horn circuit requires 12V, then a relay is required. RELAY WIRING: Connect the Brown/White wire to terminal 85, connect relay terminals 86 and 87 to 12V constant power. Connect terminal 30 of the relay to the 12V positive device/circuit to be activated.
ORANGE WIRE: (-) NEGATIVE ARMED OUTPUT / STARTER DISABLE (500mA Ground, Optional)
This wire becomes a (-) Ground output when system is armed. This output is used for disabling the starter or to activate optional devices such as extra sensors, LED’s, window roll-up modules, voice modules etc. For starter kill, cut starter wire and connect between 87A and 30 on relay. Connect orange wire to 85 and connect 86 to an Ignition source that has voltage in the ON and CRANKING position. (See wiring diagram for relay configuration-Pg. 15)
WHITE RED WIRE: (-) AUX REMOTE OUTPUT 2 (Optional, may require a r elay)
This wire connects the same way as Remote Output 1 see GRAY WIRE last page.
BLUE WHITE WIRE: NOT USED / NO CONNECTION BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.)
Connect to RED siren wire from the Siren in the engine compartment. WHITE WIRE: 12V FLASHING PARKING LIGHT OUTPUT
Connect to the switched parking light wire at back of light switch. If this is not possible, connect directly to one of the parking lights at the front of the vehicle. European vehicles require separate right and left circuits. Use a dual relay or 2 diodes to separate the output signal.
RED WIRE: 12V POWER INPUT (15 amp fuse)
Connect to 12 Volt source with supplied fuse & holder. Recommended location for this connection is at the vehicle battery positive terminal.
2 PIN PLUG (BLUE): PROGRAM/OVERRIDE PUSH-BUTTON 2 PIN PLUG (WHITE): ALARM STATUS LED INDICATOR 4 PIN SENSOR PLUG: WHITE Wire: Negative Trigger,
BLUE Wire: Negative Warn Away, BLACK Wire: Sensor Ground, RED Wire Sensor 12V Power
POWER DOOR LOCK WIRING
3 PIN DOOR LOCK PLUG (Optional): GREEN: (-) Negative LOCK Pulse, RED: 12V Coil Power for relays, BLUE: (-) Negative UNLOCK Pulse
NEGATIVE TRIGGER DOORLOCK WIRING
POSITIVE TRIGGER DOORLOCK WIRING
GREEN
GREEN
FUSED
RED
+12VRED
BLUE
+
BLUE
86
858685
8787
3087A30
87A
FACTORY
FACTORY
L
L
POWER
POWER
LOCKING
LOCKING
UL
UL
RELAYS
RELAYS
ADDING A FTERMARKET DOOR LOCK MOTORSREVERSE POLARITY DOOR LOCK WIRING
GREEN
GREEN
FUSED
FUSED
RED
RED
+12V
+12V
BLUE
BLUE
+
+
86858685
86858685
8787
8787
3087A3087A
3087A3087A
+
L
CUT
UL
CUT
MASTER
SWITCH
Loading...
+ 14 hidden pages