Crib Delta Children 4 in 1 Installation Manual
4 in 1 Crib
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
THIS PRODUCT IS NOT INTENDED FOR
INSTITUTIONAL OR COMMERCIAL USE.
Conforms to
ASTM F1169 Full
Size Crib & F1821
Safety Standards
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
Style #:
Lot:
Date:
___________
___________
___________
A
REV
When contacting Delta Consumer Care please reference the above information. Before contacting Delta
Consumer Care please ensure that the information above matches the information found on the label on
the Crib End bottom rail, please reference the information found on the product when contacting Delta
Consumer Care.
To register your product for important safety alerts and updates to your product please visit
www.DeltaChildren.com and click on Product Registration.
JULY 14, 2014, 24374, R1
©2014 DELTA ENTERPRISE CORP.
CAUTION:
ANY MATTRESS USED IN THIS CRIB SHALL
BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A
THICKNESS NOT EXCEEDING 6 IN.
WARNING:
*Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an
infant.
*Failure to follow these warnings and the assembly instructions could result in serious injury or death.
this crib if you cannot exactly follow the accompanying instructions.
*To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
*Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not place items with a string around a
child's neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or attach strings to toys.
*Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
*Strangulation Hazard: Do not place crib near window or patio door where cords from blinds or drapes may
strangle a child.
*Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and remove bumper
pads, large toys and other objects that could serve as steps for climbing out. This crib has an adjustable mattress
support. For the convenience of the parent when the baby is very small, the mattress support may be used in the
highest position. Important: with the mattress support and mattress in the highest position, be absolutely sure that
the top of the front crib side is at least 3 inches higher than the top surface of the mattress. If it is not, lower the
mattress support and the mattress to the next highest position.
*Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (89cm), whichever occurs
first. The child should be placed in a youth or regular bed.
*Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or sharp edges
before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners. Do not use
crib if any parts are missing, damaged or broken. Contact Delta Children's Products for replacement parts and
instructional literature if needed. Do not substitute parts.
*Follow warnings on all products in a crib.
*If refinishing, use a non-toxic finish specified for children's products.
*Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
*Infants can suffocate in gaps between crib sides and a mattress that is too small.
*Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that every
component is properly and securely in place.
*To avoid head injury, do not allow any child to play underneath the crib.
*Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
*In Canada Only - Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it is pushed
firmly against any side of the crib, it does not leave a gap of more than 3 cm between the mattress and any part of
the sides of the crib. Do not use this crib for a child who can climb out of it or who is taller than 90 cm.
DO NOT use
TODDLER BED
WARNING
INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
Openings in and between toddler bed parts can entrap head and neck of a small child.
NEVER use toddler bed with children younger than 15 months.
ALWAYS follow assembly instructions.
The maximum user weight is 50lbs (22.7kg)
WARNING
STRANGULATION HAZARD
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
NEVER suspend strings over a bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords,
around a child's neck. These items may catch on bed parts.
CAUTION
ENTRAPMENT HAZARD
To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib mattress
at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width and a max thickness of
6 in (150 mm).
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact Delta Children's Products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
3
PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
A. Back Top Rail x 1
Part # 24365
B. Back Rail x 1
Part # 24366
G. Left Back Post x 1
Part # 24371
H. Right Back Post x 1
Part # 24372
C. Front Rail x 1
Part # 24367
PRODUCT LABEL
E. Left Crib Side x 1
Part # 24369
LEFT INSIDE BOTTOM LABEL
RIGHT INSIDE BOTTOM LABEL
F. Right Crib Side x 1
Part # 24370
D. Stabilizer Bar x 1
Part # 24368
J. Mattress Support x 1
Part # 24242
POUCH ATTACHED TO MATTRESS SUPPORT
- KEEP INSTRUCTIONS IN THIS POUCH
AFTER ASSEMBLY.
WARNINGS RELATED TO THE SAFE USE OF
THIS CRIB ARE PRINTED ON THE POUCH.
4
PARTS: HARDWARE KIT IS PART #24373-986 FOR COLOR 100 OR #24373-988 FOR
COLOR 207. SEE FRONT COVER.
K. M6 x 75 mm Bolt x 10
Part # 5472
L. M6 x 55 mm Bolt x 6
Part # 5468
N. M6 x 18 mm Bolt x 4
Part # 5763
No drills necessary.
Do not use power
screwdriver.
Flat Head Screwdriver
(not supplied)
P. Φ4x30 mm Metal Pin x 2
Part # 5493
M4 Allen Wrench Supplied
Part # 1177
R. M6x17mm Barrel Nut x 14
Part # 5479
5
Section 1: Crib Assembly
Step 1
Parts and tools required to complete step.
RIGHT INSIDE
BOTTOM LABEL
F. Right Crib Side x 1
LEFT INSIDE BOTTOM LABEL
PRODUCT LABEL
G. Left Back Post x 1
H. Right Back Post x 1
R. M6x17mm Barrel Nut x 4
M4 Allen Wrench
Supplied
E. Left Crib Side x 1
L. M6 x 55 mm Bolt x 4
Attach (1) Left Back Post (Part G) to (1) Left Crib Side (Part E) using (2) M6x55 mm Bolts (Part L) and
(2) M6x17 mm Barrel Nuts (Part R). Tighten with the M4 Allen Wrench. Use the Flat Head Screwdriver
to hold the Barrel Nut in the proper alignment. Repeat with the Right Crib Side (Part F) and Right Back
Post (Part H).
L
R
G
E
LEFT INSIDE BOTTOM LABEL
PRODUCT LABEL
Left Crib Side
R
L
INSIDE
6
Loading...