Crestron electronic CP-WX8240, CP-X8150 User Manual

Projector

CP-X8150/CP-WX8240

User's Manual (detailed)
Network Guide

Thank you for purchasing this product.

This manual is intended to explain only the network function. For proper use of this
product, please refer to this manual and the other manuals for this product.

WARNING

►Before using this product, be sure to read all manuals for this

product. After reading them, store them in a safe place for future reference.

Features

This projector has the network function that brings you the following main features.

ü Network Presentation : allows the projector to project computer images transmitted

through a network. (

ü Web Control : allows you to monitor and control the projector through a network from a

computer. (

ü My Image : allows the projector to store up to four still images and project them. (
ü Messenger : allows the projector to display text sent from a computer through a network.

&51)

(

ü Network Bridge : allows you to control an external device through the projector from a

computer. (

NOTE

&16)

&52)

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

Trademark acknowledgment

• Microsoft
trademarks of Microsoft Corporation in the U.S. and/or other countries.

• Adobe

• Pentium

• JavaScript

• HDMI
registered trademarks of HDMI Licensing LLC in the United States and other countries.

• Crestron
trademarks or registered trademarks of Crestron Electronics, Inc. in
the United States and other countries.

• Trademark PJLink is a trademark applied for trademark rights in
Japan, the United States of America and other countries and areas.

All other trademarks are the properties of their respective owners.

®

, Internet Explorer®, Windows®, Windows Vista® and Aero® are registered

®

and Flash® are registered trademarks of Adobe Systems Incorporated.

®

is a registered trademark of Intel Corporation.

®

is a registered trademark of Sun Microsystems, Inc.

TM

, the HDMI logo and High-Denition Multimedia Interface are trademarks or

®

, Crestron e-Control®, e-Control®, Crestron RoomView® and RoomViewTM are

&15)

&50)

1

2

Contents

Contents

&

Caution .......................................................................................... 4

1. Connection to the network ...................................................... 5

1.1 System requirements ................................................................................. 5

1.1.1 Required equipment preparation ..................................................................................... 5

1.1.2 Hardware and software requirement for computer .......................................................... 5

1.2 Quick connection . ....................................................................................... 6

1.3 Manual network connection setting - Wired LAN -. ..................................... 7

1.3.1 Equipments connection .................................................................................................... 7

1.3.2 Network settings .............................................................................................................. 7

1.3.3 “Internet Option” setting ................................................................................................. 10

1.4 Manual network connection setting - Wireless LAN - ............................... 11

1.4.1 Preparation for wireless LAN connection ....................................................................... 11

1.4.2 Wireless LAN connection set up .................................................................................... 12

2. Network Presentation ............................................................. 15

3. Web Control ............................................................................ 16

3.1 Projector Web Control ............................................................................... 17

3.1.1 Logon ............................................................................................................................. 17

3.1.2 Network Information ....................................................................................................... 18

3.1.3 Network Settings ............................................................................................................ 19

3.1.4 Port Settings .................................................................................................................. 22

3.1.5 Mail Settings .................................................................................................................. 24

3.1.6 Alert Settings .................................................................................................................. 25

3.1.7 Schedule Settings .......................................................................................................... 27

3.1.8 Date/Time Settings ......................................................................................................... 30

3.1.9 Security Settings ............................................................................................................ 32

3.1.10 Projector Control .......................................................................................................... 33

3.1.11 Remote Control ............................................................................................................ 39

3.1.12 Projector Status ........................................................................................................... 41

3.1.13 Network Restart ........................................................................................................... 41

3.2 Crestron e-Control® .................................................................................. 42

3.2.1 Main window .................................................................................................................... 43

3.2.2 Tools window ................................................................................................................... 45

3.2.3 Info window ..................................................................................................................... 47

3.2.4 Help Desk window ........................................................................................................... 48

3.2.5 Emergency Alert .............................................................................................................. 49

4. My Image Function ................................................................. 50

5. Messenger Function ............................................................... 51

3

Contents

&

6. Network Bridge Function ....................................................... 52

6.1 Connecting devices .................................................................................. 52

6.2 Communication setup ............................................................................... 53

6.3 Communication port ................................................................................. 53

6.4 Transmission method ............................................................................... 54

6.4.1 HALF-DUPLEX .............................................................................................................. 54

6.4.2 FULL-DUPLEX ............................................................................................................... 55

7. Other Functions ...................................................................... 56

7.1 E-mail Alerts ............................................................................................. 56

7.2 Projector Management using SNMP ........................................................ 58

7.3 Event Scheduling ..................................................................................... 59

7.4 Command Control via the Network .......................................................... 62

®

7.5 Crestron RoomView

................................................................................. 67

8. Troubleshooting ..................................................................... 68

9. Specications ......................................................................... 69

10. Warranty and after-sales service ........................................ 70

4

Caution

Caution

To use the wireless network function of this projector, the designated USB wire­less adapter that is sold as an option is required. For precautions according to the

standards and laws, refer to the documents that come with the adapter.

[Restriction on plugging and unplugging the USB wireless adapter]

Before you insert or pull out the USB wireless adapter from the projector, turn off
the power of the projector and pull out the power cord’s plug from the outlet. Do
not touch the USB wireless adapter that is connected to the projector while the
projector is receiving AC power.
Do not use any extension cable or device when connecting the adapter to the projector.

[Security precautions when using wireless LAN]

It is recommended that security settings, such as SSID and ENCRYPTION, are
specied when using wireless LAN communication. If the security settings are not
specied, the contents may be intercepted or it may cause unauthorized access
to the system. For details on wireless LAN security settings, refer to 3.1 Projector

Web Control or

&NETWORK menu in the Operating Guide.

CAUTION

►The optional IEEE802.11b/g/n USB wireless adapter uses

the 2.4GHz radio frequency band. You do not need a radio license to use the

adapter, but you should be aware of the following:

DO NOT USE NEAR THE FOLLOWING!

•

• Microwave ovens

• Industrial, scientic or medical devices

• Designated low power radio stations

• Premises radio stations
Using the USB wireless adapter near the above may cause radio interference,

which would result in a decrease in transmission speed or interruption, and
even lead to malfunctioning of devices such as pacemakers.

• Depending on the location where the USB wireless adapter is used, radio wave

interference may occur, which may result in a decrease in transmission speed
or interruption in communication.In particular, please be aware that using the

USB wireless adapter at locations where there is reinforced steel, other types

of metals or concrete is likely to cause radio wave interference.

• Available Channels
The USB wireless adapter uses the 2.4GHz radio frequency band, but

depending on the country or region you are in, the channels that you can use

might be limited. Please consult your dealer for information on the usable

channels.

• Bringing the optional USB wireless adapter out of the country or region you
reside in and using it there could lead to a violation of the radio laws of that
country or region.

5

1. Connection to the network

1. Connection to the network

1.1 System requirements

1.1.1 Required equipment preparation

The following equipments are required to connect the projector to your computer

through the network.

■ Common The projector: 1 unit, Computer : minimum 1 set

■ Depending on how you want to connect

1) For the wired connection *1

LAN cable (CAT-5 or greater): 1 piece

2) For the wireless connection *2

- Projector side
IEEE802.11b/g/n USB wireless adapter (option : USB-WL-11N) : 1 unit

- Computer side
IEEE802.11 b/g/n wireless LAN equipment: 1 unit for each *3

*1: The system for using the network function of the projector requires

communication environment conforming 100Base-TX or 10Base-T.

*2: An access point is required when the wireless LAN connection is used as

Infrastructure mode.

*3: Depending on the type of wireless network device and computer you are using,

the projector may not be able to communicate properly with your computer,

even if the computer is equipped with a built-in wireless LAN function.
To eliminate communication problems, please use a Wi-Fi certied wireless

network device.

1.1.2 Hardware and software requirement for computer

To connect your computer to the projector and use the network function of the

projector, your computer needs to meet the following requirements.

ü OS: One of the following.

Windows

®

XP Home Edition /Professional Edition (32 bit version only)

Windows Vista® Home Basic /Home Premium /Business /Ultimate /Enterprise
(32 bit version only)
Windows® 7 Starter /Home Basic /Home Premium /Professional /Ultimate /
Enterprise (32 bit version only)

ü CPU: Pentium 4 (2.8 GHz or higher)
ü Graphic card: 16 bit, XGA or higher

* When using the “LiveViewer” it is recommended that the display resolution of

your computer is set to 1024 x 768.

ü Memory: 512 MB or higher
ü Hard disk space: 100 MB or higher
ü Web browser: Internet Explorer

®

6.0 or higher

ü CD-ROM/DVD-ROM drive

6

1. Connection to the network

1.1 System requirements (continued)

NOTE

• The network communication control is disabled while the projector is
in standby mode if the STANDBY MODE item is set to SAVING. Please connect
the network communication to the projector after setting the STANDBY MODE
to NORMAL. (

&SETUP menu in the Operating Guide)

• You can get the latest version of the applications for the network functions of
the projector and the latest information for this product from the Hitachi website.
(http://www.hitachi-america.us/digitalmedia or http://www.hitachidigitalmedia.

com).

1.2 Quick connection

The “LiveViewer” supports very quick and simple connection to the network.

When making use of the network function, it is recommended that you install the

"LiveViewer" on your computer. For details, refer to the manual for "LiveViewer".

In case you don’t want to use the “LiveViewer” or you cannot use it by some
reason, proceed to the manual setting, the item 1.3 for the wired LAN (
the item 1.4 for the wireless LAN. (&11)

&7) and

7

1. Connection to the network

1.3 Manual network connection setting - Wired LAN -

This section explains how to set it up manually.

1.3.1 Equipments connection

Connect the projector and a computer with a LAN cable.
* Before connecting with an existing network, contact the network administrator.

Next, check the following computer settings.

1.3.2 Network settings

®

This is the explanation of network connection settings for Windows
Explorer.

1) Log on to Windows

®

7 as administrator authority. Administrator authority is the

account, which can access to all functions.

2) Open “Control Panel” from “Start” menu.

3) Open “View network status and tasks” in “Network and Internet”.
With the icons in the "Control Panel" window displayed, click "Network and
Sharing Center"..

7 and Internet

4) Click "Change adapter settings" in the menu
on the left side of the "Network and Sharing
Center" window.

(continued on next page)

8

1. Connection to the network

1.3 Manual network connection setting - Wired LAN - (continued)

5) Right-click "Local Area Connection" to open the menu,
and select "Properties".

6) Select "Internet Protocol Version 4 (TCP/IPv4)" and click
[Properties].

7) Select "Use the following IP address" and congure the IP
address, Subnet mask and Default gateway for the computer
accordingly. If a DHCP server exists in the network, you
can select "Obtain an IP address automatically" and the IP

address will be assigned automatically.
After setting is complete, click [OK] to close the window.

(continued on next page)

9

1. Connection to the network

1.3 Manual network connection setting - Wired LAN - (continued)

[About IP address]

■ Setting manually

The Network address portion of the IP address setting on your computer must
be the same as the setting on the projector. Also, the entire IP address on the

computer must not overlap with that of the other devices on the same network,
including the projector.

For example

The projector’s settings are as follows.

IP address: 192.168.1.254
Subnet mask: 255.255.255.0
(Network address: 192.168.1 in this case)

Therefore, specify the computer’s IP address as follows.

IP address: 192.168.1.xxx (xxx shows decimal number.)
Subnet mask: 255.255.255.0
(Network address: 192.168.1 in this case)

Select from 1 to 254 for “xxx” not duplicating with any other equipments.
In this case, since the IP address of the projector is “192.168.1.254”, specify a

setting between 1 to 253 for the computer.

NOTE

• “0.0.0.0” cannot be set to the IP address.

• The projector’s IP address can be changed by using the conguration utility

via a web browser. (

&21)

• If the projector and the computer exist in the same network (i.e., same
network address), you can leave the default gateway eld blank.

• When the projector and the computer exist in different networks, the default
gateway must be set. Consult to the network administrator in detail.

■ Setting automatically

When a DHCP server exists in the connected network, it is possible to assign an
IP address to the projector and computer automatically.

* DHCP is abbreviation for “Dynamic Host Conguration Protocol” and has the

function to provide necessary setting for network like IP address from server to
client. A server that has DHCP function is called DHCP server.

(continued on next page)

10

1. Connection to the network

1.3 Manual network connection setting - Wired LAN - (continued)

1.3.3 “Internet Option” setting

1) Click “Internet Options” in “Network and
Sharing Center” window to open “Internet
Properties” window.

2) Click “Connections” tab and then click [LAN settings] button
to open “Local Area Network (LAN) Settings”.

3) Uncheck all boxes in “Local Area Network (LAN) Settings”

window.
After setting is complete, click [OK] to close the window.

11

1. Connection to the network

1.4

Manual network connection setting

Using the designated USB wireless adapter (option) on the projector enables the
projector and computer to communicate in both the Ad-Hoc and Infrastructure

modes.

This section is intended to explain how to set up wireless LAN connection

manually.

1.4.1 Preparation for wireless LAN connection

Fig. 1.4.1.a Without an access point communication (Ad-Hoc)

Fig. 1.4.1.b With an access point communication (Infrastructure)

-

Wireless LAN -

* Ad-Hoc is one of the wireless LAN communication methods without having

access point to communicate.

* Infrastructure is one of the wireless LAN communication methods with having

access point to communicate. If certain quantities of equipments are used, this
mode is efcient.

If communicating with existing network, consult to your network administrator.

First, insert the USB wireless adapter into the USB TYPE A port.
(

& Connecting with your devices in the Operating Guide)

Then, set up the computer for wireless communication.

When the computer comes with a built-in IEEE802.11b/g/n wireless LAN device,
enable it and disable other network connections. If a wireless LAN device is not
built into the computer, connect an IEEE802.11b/g/n wireless LAN device and

install the device driver. For details, refer to the user's guide for the computer and

wireless LAN device.

12

1. Connection to the network

1.4 Manual network connection setting - Wireless LAN - (continued)

1.4.2 Wireless LAN connection set up

®

Using wireless LAN utility for Windows

7 standard.

Wireless LAN initial settings for the projector is as follows.

Connection Control : Ad-Hoc
SSID : wireless
Channel : 1
Encryption rating : None
IP address : 192.168.10.254

* You can change these settings via a web browser on your computer or from the

menu of the projector. Refer to the item 3.1.3 Network Settings (

&20) or

NETWORK menu in the Operating Guide.

1) Select "Change adapter settings" from the
menu on the left side of the "Network and
Sharing Center" window.

2) Right-click "Wireless Network Connection" to open the
menu, and select "Properties".

3) Select "Internet Protocol Version 4 (TCP/IPv4)" and click
[Properties].

(continued on next page)

13

1. Connection to the network

1.4 Manual network connection setting - Wireless LAN - (continued)

4) Select "Use the following IP address" and congure the IP
address, Subnet mask and Default gateway for the computer

accordingly.
After setting is complete, click [OK] to close the window.

[About IP address]

The Network address portion of the IP address setting on your computer must
be the same as the setting on the projector. Also, the entire IP address on the

computer must not overlap with that of the other devices on the same network,
including the projector.

For example

The projector’s settings are as follows.

IP address: 192.168.10.254
Subnet mask: 255.255.255.0
(Network address: 192.168.10 in this case)

Therefore, specify the computer’s IP address as follows.

IP address: 192.168.10.xxx (xxx shows decimal number.)
Subnet mask: 255.255.255.0
(Network address: 192.168.10 in this case)

Select from 1 to 254 for “xxx” not duplicating with any other equipments.
In this case, since the IP address of the projector is “192.168.10.254”, specify

a setting between 1 to 253 for the computer.

NOTE

• “0.0.0.0” cannot be set to the IP address.

• The projector’s IP address can be changed by using the conguration utility

via a web browser. (

&20)

• If the projector and the computer exist in the same network (i.e., same
network address), you can leave the default gateway eld blank.

• When the projector and the computer exist in different networks, the default

gateway must be set.

(continued on next page)

14

1. Connection to the network

1.4 Manual network connection setting - Wireless LAN - (continued)

5) Right-click "Wireless Network Connection" to open
the menu, and select "Connect / Disconnect".

6) From the connectable wireless networks, select the SSID of the
projector (set to "wireless" by default), and click [Connect]. If

you have enabled encryption, a window asking for input of the
encryption key will be displayed. Input the preset key.

7) After connection is established, "Connected" will appear to the

right of SSID.

15

2. Network Presentation

2. Network Presentation

The projector can display or play back the computer screen images and audio

data that are transmitted through the network. This Network Presentation feature

helps you to smoothly make your presentations and conduct conferences.

Wireless LAN

Wired LAN

To use Network Presentation, an exclusive application, "LiveViewer" is required.
It can be installed from the bundled application CD. You can also download the
latest version and relevant information from the Hitachi website (http://www.
hitachi-america.us/digitalmedia or http://www.hitachidigitalmedia.com). For details
of Network Presentation and instructions to install the "LiveViewer", refer to the
manual for "LiveViewer".

To start the Network Presentation, select the LAN port as the input source on the
projector and click the Starting Capture button on the “LiveViewer”.
"LiveViewer" function use depends on the model you are using. If you want to use
the latest downloaded "LiveViewer", please refer for the appropriate group item in
the "LiveViewer" User's Manual. This model will be in the Group of E.

16

3. Web Control

3. Web Control

You can adjust or control the projector via a network from a web browser on a

computer that is connected to the same network.

NOTE

• Internet Explorer® 6.0 or later is required.

• If JavaScript® is disabled in your web browser conguration, you must enable
JavaScript® in order to use the projector web pages properly. See the Help les
for your web browser for details on how to enable JavaScript®.

• It is recommended that all web browser updates are installed.

• If data is transferred via wireless and wired LAN at the same time, the

projector may not be able to process the data correctly.

Refer to the following for conguring or controlling the projector via a web browser.
Make sure that your computer and the projector is connected via network, and

then start Web browser.

Enter the projector's IP address into URL input box of the Web browser as the

example below, and then press the Enter key or button.
Example: If the IP address of the projector is set to 192.168.1.10:

Enter “http://192.168.1.10/” into the address bar of the web browser
and press the Enter key or click

button.

If a correct URL is input, and the

projector and your computer are
connected to the same network
correctly, the selection window as
shown on the right will be displayed.

You can choose to use Projector Web
Control or Crestron e-Control® as a tool
for controlling the projector. Click one of

them.
For more details, refer to 3.1 Projector
Web Control (

&17) or 3.2 Crestron

e-Control® (&42).

NOTE

• Do not attempt to control the projector with the projector's menu or

remote control, and via Web Control at the same time. It may cause some

operational errors in the projector.

• If Crestron e-Control in the Network Settings (

&21) is set to Disable,
the selection window above does not appear, but the Logon window of the
Projector Web Control is displayed.

®

• Crestron e-Control

is created using Flash®. You need to install Adobe® Flash®

Player on your computer to use Crestron e-Control®.

17

3.1 Projector Web Control

3.1.1 Logon

To use the Projector Web Control function, you need

to logon with your user name and password.

Below are the factory default settings for user

name and password.

3. Web Control

User name Password

Logon window

Administrator <blank>

Enter your user name and password, and then click the [OK].
If you logon successfully, the screen below will be displayed.

Main menu

Click the desired operation or conguration item on the main menu.

NOTE

• The language used on the Projector Web Control screen is the
same as that of the OSD on the projector. If you want to change it, you need
to change the OSD language on the projector. (

&SCREEN menu in the

Operating Guide)

18

3. Web Control

3.1 Projector Web Control (continued)

3.1.2 Network Information

Displays the projector’s current network
conguration settings.

Item Description

Common Information

Projector Name Displays the projector name settings.

Wireless Information Displays the current settings of wireless LAN.

Mode Displays the mode of wireless LAN communication.

DHCP Displays the DHCP setting.

IP Address Displays the IP address.
Subnet Mask Displays the subnet mask.

Default Gateway Displays the default gateway.
DNS Server Address Displays the DNS server address.

MAC Address Displays the MAC address.
Ch Displays the channel used for wireless LAN.
Encryption Displays the data encryption setting.

SSID Displays the SSID used by the projector.

Speed Displays the current wireless LAN transmission speed.

Wired Information Displays the current wired LAN settings.

DHCP Displays the DHCP setting.

IP Address Displays the IP address.
Subnet Mask Displays the subnet mask.

Default Gateway Displays the default gateway.
DNS Server Address Displays the DNS server address.

MAC Address Displays the MAC address.

Displays information common to both wireless and wired
LAN.

19

3.1 Projector Web Control (continued)

3.1.3 Network Settings

Displays and congures network settings.

Item Description

Common Setup

Projector Name

sysLocation (SNMP)

sysContact (SNMP)

AMX D.D.
(AMX Device
Discovery)

Congures the settings common to wireless and wired LAN.
Congures the name of the projector.

The length of the Projector Name can be up to 64

alphanumeric characters. Only alphabets, numbers and
following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space.
Particular projector name is pre-assigned by default.

Congures the location to be referred to when using SNMP.
The length of the sysLocation can be up to 255 alphanumeric
characters. Only numbers ‘0-9’ and alphabet ‘a-z’, ‘A-Z’ can

be used.

Congures the contact information to be referred to when
using SNMP.
The length of the sysContact can be up to 255 alphanumeric
characters. Only numbers ‘0-9’ and alphabet ‘a-z’, ‘A-Z’ can

be used.

Congures the AMX Device Discovery setting to detect the
projector from the controllers of AMX connected to the same
network. For the details of AMX Device Discovery, visit the
AMX web site.

URL: http://www.amx.com (as of Aug. 2011)

3. Web Control

(continued on next page)

20

3. Web Control

3.1 Projector Web Control - Network Settings (continued)

Item Description

Wireless Setup Congures the wireless LAN settings.

Mode Select "Ad-Hoc" or "Infrastructure".

IP Conguration Congures network settings.

DHCP ON Enables DHCP.
DHCP OFF Disables DHCP.

IP Address Congures the IP address when DHCP is disabled.
Subnet Mask Congures the subnet mask when DHCP is disabled.

Default

Gateway

DNS Server Address Congures the DNS server address.

Ch

Encryption Select data encryption method.

WEP Key

WPA Passphrase

SSID

Congures the default gateway when DHCP is disabled.

Select from “1” to “11” a channel to use in the Ad-Hoc mode.

NOTE

• Depending on the country where you are

the channels may vary. In addition, depending on the

country or region where you are may be required to use a
wireless network card that conrm to the standards in the

respective country or region.

Input the WEP key.
Either ASCII characters or hexadecimal numbers can be
used during WEP key input. However, you cannot use a
combination of both.The length of the key is dened as
follows according to the WEP and character formats.

Encryption ASCII characters HEX numbers
WEP 64bit 5 characters 10 characters

WEP 128bit 13 characters 26 characters

Input WPA Passphrase.

Available number of input characters is 8 to 63. Only
alphabets, numbers and following symbols can be used.

!"#$%&'()*+,-./:;<=>?@ [\]^_`{|}~ and space
Select an SSID from the list.

If you require to set your unique SSID, select [Custom], then
set your own SSID following the rules below.
Maximum number of input characters is 32.

Only alphabets, numbers and following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space.

(continued on next page)

21

3.1 Projector Web Control - Network Settings (continued)

Item Description

Wired Setup Congures the wired LAN settings.

IP Conguration Congures network settings.

DHCP ON Enables DHCP.
DHCP OFF Disables DHCP.

IP Address Congures the IP address when DHCP is disabled.
Subnet Mask Congures the subnet mask when DHCP is disabled.

Default

Gateway

DNS Server Address Congures the DNS server address.

Other Setup Congures other network settings.

Crestron e-Control

Congures the default gateway when DHCP is disabled.

Set whether to or not to use Crestron e-Control
If you choose Disable, the Logon window of Projector Web
Control and not the selection window will be displayed at rst
of the Web Control.

Click the [Apply] button to save the settings.

3. Web Control

®

.

NOTE

• The new conguration settings are activated after restarting the
network connection. When the conguration settings are changed, you must
restart the network connection. You can restart the network connection from

Network Restart on the main menu (

&41).

• If you connect the projector to an existing network, consult a network

administrator before setting server addresses.

• The WEP Key, WPA passphrase and SSID settings will not be set if the invalid

characters are used.

• The projector does not allow both wireless and wired LAN to be connected to
the same network. Do not set the same network address for both wireless and
wired LAN.

22

3. Web Control

3.1 Projector Web Control (continued)

3.1.4 Port Settings

Displays and congures communication port

settings.

Item Description

Network Control Port1
(Port:23)

Port open Click the [Enable] check box to use port 23.

Authentication

Network Control Port2
(Port:9715)

Port open Click the [Enable] check box to use port 9715.

Authentication

PJLink

TM

Port

(Port:4352)

Port open Click the [Enable] check box to use port 4352.

Authentication

My Image Port
(Port:9716)

Port open Click the [Enable] check box to use port 9716.

Authentication

Messenger Port
(Port:9719)

Port open Click the [Enable] check box to use port 9719.

Authentication

Congures command control port 1 (Port:23).

Click the [Enable] check box when authentication is required

for this port.

Congures command control port 2 (Port:9715).

Click the [Enable] check box when authentication is required

for this port.

Congures the PJLink

TM

port (Port:4352).

Click the [Enable] check box when authentication is required

for this port.

Congures the My Image Port (Port:9716).

Click the [Enable] check box when authentication is required

for this port.

Congures the Messenger Port (Port:9719).

Click the [Enable] check box when authentication is required

for this port.

(continued on next page)

23

3.1 Projector Web Control - Port Settings (continued)

Item Description

SNMP Port Congures the SNMP port.

Port open Click the [Enable] check box to use SNMP.

Congures the destination of the SNMP Trap in IP format.

Trap address

Download MIB le Downloads a MIB le from the projector.

Network Bridge Port Congures the Bridge port number.

Port number

• The address allows not only IP address but also domain
name if the valid DNS server is setup in the Network

Settings. The maximum length of host or domain name is up
to 255 characters.

Input the port number.
Except for 41794, 9715, 9716, 9719, 9720, 5900, 5500, 4352
between 1024 and 65535 can be set up. It is set to 9717 as
the default setting.

Click the [Apply] button to save the settings.

3. Web Control

NOTE

• The new conguration settings are activated after restarting the
network connection. When the conguration settings are changed, you must
restart the network connection. You can restart the network connection from

Network Restart on the main menu(

&41).

24

3. Web Control

3.1 Projector Web Control (continued)

3.1.5 Mail Settings

Displays and congures e-mail addressing

settings.

Item Description

Send Mail

SMTP Server Address

Sender E-mail address

Recipient E-mail address

Click the [Enable] check box to use the e-mail function.
Congure the conditions for sending e-mail under the Alert

Settings.

Congures the address of the mail server in IP format.

• The address allows not only IP address but also domain
name if the valid DNS server is setup in the Network

Settings. The maximum length of host or domain name is up
to 255 characters.

Congures the sender e-mail address.
The length of the sender e-mail address can be up to 255

alphanumeric characters.

Congures the e-mail address of up to ve recipients. You

can also specify the [TO] or [CC] for each address. The

length of the recipient e-mail address can be up to 255

alphanumeric characters.

Click the [Apply] button to save the settings.

NOTE

• You can conrm whether the mail settings work correctly using the

[Send Test Mail] button. Please enable Send mail setting before clicking the
[Send Test Mail].

• If you connect the projector to an existing network, consult a network

administrator before setting server addresses.

25

3.1 Projector Web Control (continued)

3.1.6 Alert Settings

Displays and congures failure & alert settings.

Item Description

Cover Error The lamp cover has not been properly xed.

Fan Error The cooling fan is not operating.

Lamp Error

Temp Error

Air Flow Error The internal temperature is rising.

Cold Error

Filter Error Filter time over.

Other Error

Schedule Execution
Error

Lamp Time Alarm Lamp time over Alarm Time setting.

Filter Time Alarm Filter time over Alarm Time setting.

Filter Status Notication The status to clean the air lter is changed.

Transition Detector

Alarm

Cold Start

Authentication Failure

The lamp does not light, and there is a possibility that interior
portion has become heated.

There is a possibility that the interior portion has become heated.

There is a possibility that the interior portion has become
overcooled.

Other error.
If displaying this error, please contact your dealer.

Schedule Execution error. (

Transition Detector Alarm. (

Operating Guide)

When the projector is supplied with the power, it works as
below.

•

If the STANDBY MODE is set to the NORMAL:the projector's

power status changes from “OFF” to “Standby state”.

•

If the STANDBY MODE is set to the SAVING:the projector's power

status changes from “Standby state” to “ON (lamp is turned on)”.

(

SETUP menu in the Operating Guide)

&

The SNMP access is detected from the invalid SNMP community.

)

&27

SECURITY menu in the

&

3. Web Control

Refer to &Troubleshooting in the Operating Guide for further detailed
explanation of Error except Other Error and Schedule Execution Error.

26

3. Web Control

3.1 Projector Web Control - Alert Settings (continued)

The Alert Items are shown below.

Item Description

Alarm Time

SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts.

Send Mail

Mail Subject

Mail Text

Congures the time to alert.

(Only Lamp Time Alarm and Filter Time Alarm.)

Click the [Enable] check box to enable e-mail alerts.

(Except Cold Start and Authentication Failure.)

Congures the subject line of the e-mail to be sent.

The length of the subject line can be up to 100 alphanumeric
characters.
(Except Cold Start and Authentication Failure.)

Congures the text of the e-mail to be sent.

The length of the text can be up to 1024 alphanumeric
characters, but if you are using some of special characters
below the length may be shorter.

Special characters " ' : & , % \

(Except Cold Start and Authentication Failure.)

and space

Click the [Apply] button to save the settings.

NOTE

• The trigger of Filter Error e-mail is depending on the FILTER
MESSAGE setting in the SERVICE item of the OPTION menu which denes
the period until the lter message is displayed on the projector screen. An
e-mail will be sent when the usage time of the lter exceeds the time limit that is
set. No notication e-mail will be sent if the FILTER MESSAGE is set to TURN

OFF. (

&OPTION menu in the Operating Guide)

• Lamp Time Alarm is dened as a threshold for e-mail notication (reminder)
of the lamp time. When the lamp hour exceeds the limit that is congured in the
Projector Web Control, an e-mail will be sent.

• Filter Time Alarm is dened as a threshold for e-mail notication (reminder)
of the lter time. When the lter hour exceeds the limit that is congured in the
Projector Web Control, an e-mail will be sent.

• Filter Status Notication can be enabled for both or either one of Status

1 and 2. These notications are equivalent to the changing of the FILTER
indicator on the projector. (Status 1: off to orange, Status 2: orange to red)
Refer to the Operating Guide for details of the FILTER indicator.

27

3.1 Projector Web Control (continued)

3.1.7 Schedule Settings

Displays and congures schedule settings.

Item Description

Daily Congures the daily schedule.

Sunday Congures the Sunday schedule.
Monday Congures the Monday schedule.
Tuesday Congures the Tuesday schedule.
Wednesday Congures the Wednesday schedule.
Thursday Congures the Thursday schedule.
Friday Congures the Friday schedule.
Saturday Congures the Saturday schedule.

Specic date No.1 Congures the specic date (No.1) schedule.
Specic date No.2 Congures the specic date (No.2) schedule.
Specic date No.3 Congures the specic date (No.3) schedule.
Specic date No.4 Congures the specic date (No.4) schedule.
Specic date No.5 Congures the specic date (No.5) schedule.

3. Web Control

28

3. Web Control

3.1 Projector Web Control - Schedule Settings (continued)

The schedule settings are shown below.

Item Description

Schedule Click the [Enable] check box to enable the schedule.

Date (Month/Day)

Congures the month and date.
This item appears only when Specic date (No. 1-5) is

selected.

Click the [Apply] button to save the settings.

The current event settings are displayed on the schedule list. To add additional
functions and events, set the following items.

Item Description

Time Congures the time to execute commands.

Command
[Parameter]

Power Congures the parameters for power control.
Input Source Congures the parameters for input switching.

My Image
Messenger Congures the parameters for Messenger data display. (
Slideshow Congures the Start/Stop parameters for the Slideshow.

Congures the commands to be executed.

Congures the parameters for My Image data display. (

&50)

&51

)

Click the [Register] button to add new commands to the schedule list.

Click the [Delete] button to delete commands from the schedule list.

Click the [Reset] button to delete all commands and reset the schedule settings

from the schedule list.

29

3.1 Projector Web Control - Schedule Settings (continued)

3. Web Control

NOTE

• After the projector is moved, check the date and time set for the
projector before conguring the schedules.

• The internal clock’s time may not remain accurate. Using SNTP is

recommended to maintain accurate time.

• Events “My Image” and “Messenger” will not be executed appropriately but
result in “schedule execution error” status in case lamp does not light or/and

display data are not stored in the projector at the scheduled event execution
time.

• Events “Input Source” and “My Image” will not be executed if security feature
is enabled and the projector is locked due to the feature.

• Certain error state in the projector (such as temperature error, lamp error) will
prevent the projector from appropriate execution of scheduled functions/events.

• If no USB memory device is inserted to the projector or no image data for

display exists at the scheduled event time, a schedule execution error occurs

against the scheduled Slideshow event.

• When you start the Slideshow, input source will be automatically switched to

the USB TYPE A port.

• Image les stored in the root directory of the USB memory device will be
displayed for the scheduled Slideshow.

• Please refer to

&Troubleshooting in the Operating Guide in case

scheduled functions/events are not executed appropriately as you've set.

30

3. Web Control

3.1 Projector Web Control (continued)

3.1.8 Date/Time Settings

Displays and congures the date and time

settings.

Item Description

Current Date Congures the current date in year/month/day format.

Current Time Congures the current time in hour:minute:second format.

Daylight Savings Time

Start Congures the date and time daylight savings time begins.

Month Congures the month daylight savings time begins (1~12).

Week

Day

Time

End Congures the date and time daylight savings time ends.

Month Congures the month daylight savings time ends (1 ~ 12).

Week

Day

Time

hour Congures the hour daylight savings time begins (0 ~ 23).
minute Congures the minute daylight savings time begins (0 ~ 59).

hour Congures the hour daylight savings time ends (0 ~ 23).
minute Congures the minute daylight savings time ends (0 ~ 59).

Click the [ON] check box to enable daylight savings time and
set the following items.

Congures the week of the month daylight savings time
begins (First, 2, 3, 4, Last).

Congures the day of the week daylight savings time begins
(Sun, Mon, Tue, Wed, Thu, Fri, Sat).

Congures the week of the month daylight savings time ends
(First, 2, 3, 4, Last).

Congures the day of the week daylight savings time ends
(Sun, Mon, Tue, Wed, Thu, Fri, Sat).

(continued on next page)

31

3.1 Projector Web Control - Date/Time Settings (continued)

Item Description

Time difference

SNTP

SNTP Server Address

Cycle

Congures the time difference. Set the same time difference

as the one set on your computer. If unsure, consult your IT
manager.

Click the [ON] check box to retrieve Date and Time
information from the SNTP server and set the following items.

Congures the SNTP server address in IP format.

• The address allows not only IP address but also domain
name if the valid DNS server is setup in the Network

Settings. The maximum length of host or domain name is up
to 255 characters.

Congures the interval at which to retrieve Date and Time
information from the SNTP server (hour:minute).

Click the [Apply] button to save the settings.

3. Web Control

NOTE

• The new conguration settings are activated after restarting the
network connection. When the conguration settings are changed, you must
restart the network connection. You can restart the network connection from

Network Restart on the main menu(

&41).

• If you connect the projector to an existing network, consult a network

administrator before setting server addresses.

• Once you turn off the projector in the SAVING mode (&SETUP menu in the
Operating Guide) or the AC power, the current date and time setting is reset.

• To enable the SNTP function, the time difference must be set.

• The projector will retrieve Date and Time information from the time server and
override time settings when SNTP is enabled.

• The internal clock’s time may not remain accurate. Using SNTP is

recommended to maintain accurate time.

32

3. Web Control

3.1 Projector Web Control (continued)

3.1.9 Security Settings

Displays and congures passwords and other

security settings.

Item Description

User Account Congures the user name and password.

User name

Password

Re-enter Password Reenter the above password for verication.

Network Control

Authentication
Password

Re-enter
Authentication
Password

SNMP Congures the community name if SNMP is used.

Community name

Congures the user name.

The length of the text can be up to 32 alphanumeric
characters.

Congures the password.

The length of the text can be up to 255 alphanumeric
characters.

Congures the Authentication password for Network Control
Port1 (Port: 23), Network Control Port2 (Port: 9715),
PJLink™ Port (Port: 4352), My Image Port (Port: 9716),
and Messenger Port (Port: 9719) (

Congures the Authentication password.

The length of the text can be up to 32 alphanumeric
characters.

Reenter the above password for verication.

Congures the community name. The length of the text can

be up to 64 alphanumeric characters.

&22, 23)

.

Click the [Apply] button to save the settings.

NOTE

• The new conguration settings are activated after restarting the
network connection. When the conguration settings are changed, you must
restart the network connection. You can restart the network connection from

Network Restart on the main menu(

&41).

• Only numbers ‘0-9’ and alphabet ‘a-z’, ‘A-Z’ can be used.

33

3.1 Projector Web Control (continued)

3.1.10 Projector Control

Operations of the projector can be performed
with the items on the screen.
The categories of the items are shown in the
main menu. Most of the items have a submenu.

Refer to the table below for details.

3. Web Control

NOTE

• The setting value may not match with the actual value if the user

changes the value manually. In that case, please refresh the page by clicking
the [Refresh] button.

Item Description

MAIN

POWER Turns the power on/off.
INPUT SOURCE Selects the input source.

PICTURE MODE Selects the picture mode setting.
BLANK ON/OFF Turns the BLANK screen on/off.

MUTE Turns the audio mute on/off.
FREEZE Turns Freeze on/off.

MAGNIFY

MAGNIFY POSITION V

MAGNIFY POSITION H
TEMPLATE Turns template on/off.

SHADE Turns the lens shade on(closed)/off(opened).

ZOOM Adjusts the zoom setting.
FOCUS Adjusts the focus setting.

LENS SHIFT V Adjusts the vertical lens shift.

LENS SHIFT H Adjusts the horizontal lens shift.
LENS MEMORY Saves, Loads or Clears the lens memory data.
MY IMAGE Selects MY IMAGE data.

MY IMAGE DELETE Deletes MY IMAGE data.

(continued on next page)

Controls the magnify setting.
In some input signal sources, it might stop “Magnify” even

though it does not reach to maximum setting value.
Adjusts the vertical magnify position.

Adjusts the horizontal magnify position.

34

3. Web Control

3.1 Projector Web Control - Projector Control (continued)

Item Description

PICTURE

BRIGHTNESS Adjusts the brightness setting.
CONTRAST Adjusts the contrast setting.
GAMMA Selects the gamma setting.
COLOR TEMP Selects the color temperature setting.
COLOR Adjusts the color setting.
TINT Adjusts the tint setting.
SHARPNESS Adjusts the sharpness setting.

ACTIVE IRIS Selects the active iris setting.
MYMEMORY SAVE Saves the MyMemory data.

MYMEMORY RECALL Recalls the MyMemory data.

IMAGE

ASPECT Selects the aspect setting.

OVER SCAN Adjusts the over scan setting.
V POSITION Adjusts the vertical position.

H POSITION Adjusts the horizontal position.
H PHASE Adjusts the horizontal phase.
H SIZE Adjusts the horizontal size.

AUTO ADJUST

EXECUTE

INPUT

PROGRESSIVE Selects the progressive setting.
VIDEO NR Selects the video noise reduction setting.

COLOR SPACE Selects the color space.
COMPONENT Selects the COMPONENT port setting.

VIDEO FORMAT ­S-VIDEO

VIDEO FORMAT ­VIDEO

HDMI FORMAT -
HDMI 1

HDMI FORMAT -
HDMI 2

HDMI RANGE -
HDMI 1

HDMI RANGE -
HDMI 2

(continued on next page)

Performs the automatic adjustment.

Selects the s-video format setting.

Selects the video format setting.

Selects the HDMI

Selects the HDMI

Selects the HDMI

Selects the HDMI

TM

format setting of the HDMI 1 port.

TM

format setting of the HDMI 2 port.

TM

range setting of the HDMI 1 port.

TM

range setting of the HDMI 2 port.

35

3.1 Projector Web Control - Projector Control (continued)

Item Description

INPUT (continued)

COMPUTER IN ­COMPUTER IN1

COMPUTER IN ­COMPUTER IN2

FRAME LOCK ­COMPUTER IN1

FRAME LOCK ­COMPUTER IN2

FRAME LOCK - HDMI 1
FRAME LOCK - HDMI 2

SETUP

AUTO KEYSTONE
EXECUTE

KEYSTONE V Adjusts the vertical keystone distortion setting.

KEYSTONE H Adjusts the horizontal keystone distortion setting.

PERFECT FIT

AUTO ECO MODE Turns on/off the automatic eco mode function.
ECO MODE Selects the eco mode.

INSTALLATION Selects the installation status.

STANDBY MODE Selects the standby mode.

MONITOR OUT ­COMPUTER IN1

MONITOR OUT ­COMPUTER IN2

MONITOR OUT - LAN
MONITOR OUT -

USB TYPE A
MONITOR OUT -

USB TYPE B
MONITOR OUT -

HDMI 1

MONITOR OUT -

HDMI 2

MONITOR OUT ­COMPONENT

MONITOR OUT -

S-VIDEO
MONITOR OUT - VIDEO

MONITOR OUT -

STANDBY

(continued on next page)

Selects the COMPUTER IN1 input signal type.

Selects the COMPUTER IN2 input signal type.

Turns the FRAME LOCK-COMPUTER IN1 function on/off.

Turns the FRAME LOCK-COMPUTER IN2 function on/off.

Turns the FRAME LOCK-HDMI 1 function on/off.
Turns the FRAME LOCK-HDMI 2 function on/off.

Performs the automatic keystone distortion setting.

Adjusts the shape of the projected image in each of the
corners and sides.

Assigns the MONITOR OUT when the COMPUTER IN1 input
port is selected.

Assigns the MONITOR OUT when the COMPUTER IN2 input
port is selected.

Assigns the MONITOR OUT when the LAN input port is selected.
Assigns the MONITOR OUT when the USB TYPE A input

port is selected.
Assigns the MONITOR OUT when the USB TYPE B input

port is selected.
Assigns the MONITOR OUT when the HDMI 1 input port is

selected.
Assigns the MONITOR OUT when the HDMI 2 input port is

selected.
Assigns the MONITOR OUT when the COMPONENT input

port is selected.
Assigns the MONITOR OUT when the S-VIDEO input port is

selected.
Assigns the MONITOR OUT when the VIDEO input port is selected.

Assigns the MONITOR OUT in the standby mode.

3. Web Control

36

3. Web Control

3.1 Projector Web Control - Projector Control (continued)

Item Description

AUDIO

VOLUME Adjusts the volume setting.

SPEAKER Turns the built-in speaker on/off.

AUDIO SOURCE -

COMPUTER IN1

AUDIO SOURCE -

COMPUTER IN2

AUDIO SOURCE - LAN Assigns the AUDIO SOURCE - LAN input port.
AUDIO SOURCE - USB

TYPE A

AUDIO SOURCE - USB

TYPE B

AUDIO SOURCE ­HDMI 1

AUDIO SOURCE ­HDMI 2

AUDIO SOURCE -

COMPONENT

AUDIO SOURCE ­S-VIDEO

AUDIO SOURCE ­VIDEO

AUDIO SOURCE ­AUDIO OUT STANDBY

HDMI AUDIO -
HDMI 1

HDMI AUDIO -
HDMI 2

SCREEN

LANGUAGE Selects the language for the OSD.

MENU POSITION V Adjusts the vertical Menu position.

MENU POSITION H Adjusts the horizontal Menu position.
BLANK Selects the BLANK screen.
START UP Selects the start up screen mode.
MyScreen Lock Turns MyScreen lock function on/off.
MESSAGE Turns the message function on/off.
TEMPLATE Selects the template setting.

C.C. - DISPLAY Selects Closed Caption DISPLAY setting.
C.C. - MODE Selects Closed Caption MODE setting.

C.C. - CHANNEL Selects Closed Caption CHANNEL setting.

Assigns the AUDIO SOURCE - COMPUTER IN1 input port.

Assigns the AUDIO SOURCE - COMPUTER IN2 input port.

Assigns the AUDIO SOURCE - USB TYPE A input port.

Assigns the AUDIO SOURCE - USB TYPE B input port.

Assigns the AUDIO SOURCE - HDMI 1 input port.

Assigns the AUDIO SOURCE - HDMI 2 input port.

Assigns the AUDIO SOURCE - COMPONENT input port.

Assigns the AUDIO SOURCE - S-VIDEO input port.

Assigns the AUDIO SOURCE - VIDEO input port.

Assigns the AUDIO SOURCE in the standby mode.

Selects the HDMI

Selects the HDMI

TM

audio setting of the HDMI 1 port.

TM

audio setting of the HDMI 2 port.

(continued on next page)

37

3.1 Projector Web Control - Projector Control (continued)

Item Description

OPTION

SOURCE SKIP ­COMPUTER IN1

SOURCE SKIP ­COMPUTER IN2

SOURCE SKIP - LAN Selects the Source Skip - LAN setting.
SOURCE SKIP -

USB TYPE A
SOURCE SKIP -

USB TYPE B
SOURCE SKIP -

HDMI 1

SOURCE SKIP -

HDMI 2

SOURCE SKIP -
COMPONENT

SOURCE SKIP -

S-VIDEO

SOURCE SKIP -

VIDEO

AUTO SEARCH Turns the automatic signal search function on/off.

AUTO KEYSTONE

DIRECT POWER ON Turns the direct power on function on/off.

AUTO POWER OFF

SHADE TIMER Selects the shade timer setting.

USB TYPE B Selects the USB TYPE B setting.

MY BUTTON-1

MY BUTTON-2

MY BUTTON-3

MY BUTTON-4

(continued on next page)

Selects the Source Skip - COMPUTER IN1 setting.

Selects the Source Skip - COMPUTER IN2 setting.

Selects the Source Skip - USB TYPE A setting.

Selects the Source Skip - USB TYPE B setting.

Selects the Source Skip - HDMI 1 setting.

Selects the Source Skip - HDMI 2 setting.

Selects the Source Skip - COMPONENT setting.

Selects the Source Skip - S-VIDEO setting.

Selects the Source Skip - VIDEO setting.

Turns the automatic keystone distortion correction function

on/off.

Congures the timer to shut off the projector when no signal

is detected.

Assigns the functions for the MY BUTTON-1 button on the
included remote control.

Assigns the functions for the MY BUTTON-2 button on the
included remote control.

Assigns the functions for the MY BUTTON-3 button on the
included remote control.

Assigns the functions for the MY BUTTON-4 button on the
included remote control.

3. Web Control

38

3. Web Control

3.1 Projector Web Control - Projector Control (continued)

Item Description

OPTION (continued)

REMOTE RECEIV. ­FRONT

REMOTE RECEIV. -

REAR
REMOTE FREQ. -

NORMAL
REMOTE FREQ. -

HIGH

REMOTE ID Selects Remote ID setting.

Turns the remote receiv. front function on/off.

Turns the remote receiv. rear function on/off.

Turns the remote control signal frequency nomal function on/

off.

Turns the remote control signal frequency high function on/

off.

This item is performed when the button is clicked

without showing another conrmation message.
Click the [Quit Presenter Mode].

Item Description

SERVICE

Quit Presenter Mode Quit compulsorily from the Presenter mode.

39

3. Web Control

3.1 Projector Web Control (continued)

3.1.11 Remote Control

The functions on the bundled remote control are

assigned to the Web Remote Control screen.

Do not attempt to control the projector with the
projector's remote control and via Web Remote
Control at the same time. It may cause some

operational errors in the projector.

Item Description

STANDBY Assigned the same operation as STANDBY button.

ON Assigned the same operation as ON button.

COMPUTER IN1 Assigned the same operation as COMPUTER IN1 button.

COMPUTER IN2 Assigned the same operation as COMPUTER IN2 button.

LAN Assigned the same operation as LAN button.

USB TYPE A Assigned the same operation as USB TYPE A button.

USB TYPE B Assigned the same operation as USB TYPE B button.

COMPONENT Assigned the same operation as COMPONENT button.

S-VIDEO Assigned the same operation as S-VIDEO button.

VIDEO Assigned the same operation as VIDEO button.

HDMI 1 Assigned the same operation as HDMI 1 button.

HDMI 2 Assigned the same operation as HDMI 2 button.

FREEZE Assigned the same operation as FREEZE button.

AV MUTE Assigned the same operation as AV MUTE button.

▲ Assigned the same operation as ▲ button.
▼ Assigned the same operation as ▼ button.
◄ Assigned the same operation as ◄ button.
► Assigned the same operation as ► button.

ENTER Assigned the same operation as ENTER button.

MENU Assigned the same operation as MENU button.

RESET Assigned the same operation as RESET button.

PAGE UP Assigned the same operation as PAGE UP button.

PAGE DOWN Assigned the same operation as PAGE DOWN button.
SLIDESHOW Starts the Slideshow.

(continued on next page)

40

3. Web Control

3.1 Projector Web Control - Remote Control (continued)

NOTE

• The Web Remote Control does not support repeat function that

performs an action while holding a button clicked down.

• Since the repeat function is not available, click the button repeatedly as many
times as you require.

•

Even if you hold the button clicked down for a while, the Web Remote Control

sends your request command one time only. Release the button, then click it again.

•

When the [STANDBY] or [ON] button is pushed, a message window comes

up to conrm the operation. To control the power, push [OK], otherwise push
[Cancel].

• The [PAGE DOWN] and [PAGE UP] buttons on the Web Remote Control
cannot be used as mouse emulation function of the projector.

41

3. Web Control

3.1 Projector Web Control (continued)

3.1.12 Projector Status

Displays the settings and status of the projector.

Item Description

Error Status Displays the current error status
Lamp Time Displays the usage time for the current lamp.
Filter Time Displays the usage time for the current lter.
Filter Status Displays the current cleanliness level of the air lter.
Power Status Displays the current power status.
Input Status Displays the current input signal source.

Blank On/Off Displays the current BLANK screen on/off status.

Mute Displays the current audio mute on/off status.
Freeze Displays the current Freeze status.
Shade Displays the current Shade status.

3.1.13 Network Restart

Restarts the projector’s network connection.

Item Description

Restart

NOTE

• Restarting requires you to re-log on in order to further control or

Restarts the projector’s network connection in order to
activate new conguration settings.

congure the projector via a web browser. Wait 30 seconds or more after

clicking the [Restart] button to log on again.

42

3. Web Control

3.2 Crestron e-Control

®

The Main window as shown above is
displayed at rst. However, if you have
enabled User Password on the Tools window

(

&46), a dialog prompting you to enter

the password as shown on the right will be
displayed, and no operation is enabled until
you have entered the password. After entering
the preset password, the dialog disappears

and the Main window will be displayed.

As shown below, you can open a window by
clicking the corresponding tab at the top right
of the window.

Tab

User Password dialog

Tab Description

Logs out from e-Control

Logout

Tools Opens Tools window
Info Opens Info window
Contact IT Help Opens Help Desk window

NOTE

• If Crestron e-Control in the Network Settings (&21) is set to
Disable, Crestron e-Control

This tab appears only when User Password of the Tools window is

enabled.

®

cannot be used to operate the projector. Enable

(

(

&47)

®

.

&45)

.

.

(

&48)

.

Crestron e-Control and close the web browser. Next, restart the web browser,
followed by entering the projector's IP address.

• Only English is supported on Crestron e-Control®.

• If the connection is terminated, the "Loading..." screen will appear. Check the

connection between the projector and the computer, then return or refresh the
Web page.

43

3.2 Crestron e-Control® (continued)

3.2.1 Main window

3. Web Control

1

2

4

3

You can operate the basic controls of the projector on this screen.

NOTE

• If the projector is in the standby mode, only the [Power] button can
be operated.

1 Click a button and operate as follows.

Button Description

Power Turns the power on/off.

Vol -/ Vol + Adjusts the volume setting.

Mute Turns the audio mute on/off.

2 Sources List

You can click a button to switch the input channel. The cursor will move

according to the currently selected input port.

Button Description

Computer in1 Selects input from COMPUTER IN1 port.
Computer in2 Selects input from COMPUTER IN2 port.
LAN Selects input from LAN port.
USB Type A Selects input from USB TYPE A port.
USB Type B Selects input from USB TYPE B port.

HDMI 1 Selects input from HDMI 1 port.
HDMI 2 Selects input from HDMI 2 port.

Component Selects input from COMPONENT port.

S-Video Selects input from S-VIDEO port.
Video Selects input from VIDEO port.

44

3. Web Control

3.2 Crestron e-Control® - Main window (continued)

3 Click a button and operate as follows. To show the hidden buttons, click the ◄ /

► icons at the left and right ends.

Button Description

Freeze Turns Freeze on/off.
Contrast Adjusts the contrast setting.
Brightness Adjusts the brightness setting.
Color Adjusts the color setting.
Sharpness Adjusts the sharpness setting.

Magnify

Auto Performs the automatic adjustment.
Blank Turns the BLANK screen on/off.

Controls the magnication setting using the [+] / [-] buttons.
Use the [▲] [▼] [◄] [►] buttons to move to the area you want

to magnify.

4 Click the button and operate in the same way as the bundled remote control.

Button Description

Menu Assigned the same operation as MENU button.
Enter Assigned the same operation as ENTER button.
Reset Assigned the same operation as RESET button.

▲ Assigned the same operation as ▲ button.

▼ Assigned the same operation as ▼ button.
◄ Assigned the same operation as ◄ button.
► Assigned the same operation as ► button.

45

3.2 Crestron e-Control® (continued)

3.2.2 Tools window

2

3. Web Control

1

3

Congures the settings between the projector and Crestron

®

Click the [Exit] button to return to the Main window.

NOTE

• If two-byte characters are used, the input text or numbers cannot be

set correctly.

• All items on this window cannot be left blank.

1 Crestron Control

Congures the settings of Crestron

Item Description

IP Address Congures the IP address of the control system.

IP ID Congures the IP ID of the control system.

Port

Species the port number used for communication by the

control system.

®

control system devices.

To apply the settings, click the [Send] button.

4

5

control system.

2 Projector

Congures the network settings of the projector.

Item Description

Projector Name

Location

Assigned To:

The usable symbols are space and the following:

Congures the name of the projector. The length of the
Projector Name can be up to 64 alphanumeric characters.

Congures the location name of the projector. You can specify
a Location name up to 32 alphanumeric characters.

Congures the user name for the projector. You can specify a

user name up to 32 alphanumeric characters.

To apply the settings, click the [Send] button.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~

46

3. Web Control

3.2 Crestron e-Control® - Tools window (continued)

3 Projector (continued)

Congures the network settings of the projector.

Item Description

DHCP Enables DHCP.

IP Address Congures the IP address when DHCP is disabled.
Subnet Mask Congures the subnet mask when DHCP is disabled.

Default Gateway Congures the default gateway when DHCP is disabled.
DNS Server Congures the DNS server address.

To apply the settings, click the [Send] button.

4 User Password

Congures the User Password. To prompt the entry of User Password before
starting e-Control

Item Description

New Password

Conrm

®

, select the checkbox.

Congures the password.
You can specify a password up to 26 alphanumeric characters.

The usable symbols are space and the following:

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~
Reenter the above password for verication. If the password is

incorrect, an error message is displayed.

To apply the settings, click the [Send] button.

5 Admin Password

Congures the Admin Password. To prompt the entry of Admin Password before

displaying the Tools window, select the checkbox.

Item Description

Congures the password.

New Password

Conrm

You can specify a password up to 26 alphanumeric characters.

The usable symbols are space and the following:

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~
Reenter the above password for verication. If the password is

incorrect, an error message is displayed.

To apply the settings, click the [Send] button.

47

3.2 Crestron e-Control® (continued)

3.2.3 Info window

1 2

Displays the settings and status of the projector.
Click the [Exit] button to return to the Main window.

1 Projector Information

Item Description

Projector Name Displays the projector name settings.
Location Displays the location name of the projector.
MAC Address Displays the wired LAN MAC address of the projector.

Resolution

Lamp Hours Displays the usage time for the current lamp.
Assigned To: Displays the user name for the projector.

Displays the resolution and vertical frequency of the signal

input selected on the projector.

3. Web Control

2 Projector Status

Item Description

Power Status Displays the current power status.
Input Source Displays the current input signal source.
Picture Mode Displays the current picture mode setting.
Installation Displays the current installation setting.
Eco Mode Displays the current eco mode setting.
Error Status Displays the current error status.

NOTE

• Projector Name, Location and the user name for Assigned To: may

appear truncated if they are too long.

48

3. Web Control

3.2 Crestron e-Control® (continued)

3.2.4 Help Desk window

Sends/receives messages to/from the administrator for Crestron RoomView®

Express.

Button Description

Send Sends a message.

Check the received message.

49

3.2 Crestron e-Control® (continued)

3.2.5 Emergency Alert

3. Web Control

When the administrator for Crestron RoomView

®

Express sends out an alert

message, it will be displayed on the screen.

You can reply to the alert message via a chat format. Input a message in the box

below the alert message, and click the [Send] button.

NOTE

• For details of Emergency Alert, refer to the manual of Crestron
RoomView® Express.

• The alert message from Crestron RoomView® is displayed on the screen of
the projector in a way similar to the real-time text of the Messenger function

(

&51). If another real-time text is currently being displayed, it will be overwritten

by the alert message. However, if the priority of the real-time text is set to high,

it will not be overwritten by the alert message, and the latter will not appear on
the screen of the projector. For details, refer to the manual for the application of

the Messenger.

50

4. My Image Function

1

43

2

4. My Image Function

The projector can display still images that are transferred via the network.

Transfer image data

Display image data (ex.

)

MY IMAGE transmission requires an exclusive application for your computer.
Use the application to transfer the image data.
It can be downloaded from the Hitachi web site (http://www.hitachi-america.us/
digitalmedia or http://www.hitachidigitalmedia.com).

For information on the necessary settings and operations for the computer and
projector, refer to the manual for the application.

To display the transferred image, select the MY IMAGE item in the NETWORK
menu. For more information, please see the description of the MY IMAGE item of
the NETWORK menu. (

NOTE

• It is possible to allocate the image le up to 4 in the maximum.

&NETWORK menu in the Operating Guide)

• Using MY BUTTON that registered MY IMAGE can display transferred image.

(

&OPTION menu in the Operating Guide)

• The image le also can be displayed by using schedule function from the web
browser. Refer to item 7.3 Event Scheduling (&59) in detail.

• If you display MY IMAGE data on screen while you are using the USB Display
function, the application for the USB Display will be closed. To restart the
application, exit the MY IMAGE function, and then the software in the projector,
LiveViewerLiteUSB.exe, will run again. (&USB Display in the Operating

Guide)

• If data is transferred via wireless and wired LAN at the same time, the

projector may not be able to process the data correctly.

51

5. Messenger Function

1

4

3

2

12

5. Messenger Function

The projector can display text data transferred via the network on the screen and
play back audio data inside the projector.
The text data can be displayed on the screen in two ways that displays the text
transferred from the computer on real time, and the other chooses and displays
the text data from the ones once stored in the projector.

Transfer text data

Display text data (ex.

)

Messenger function requires an exclusive application for your computer. To
edit, transfer and display the text data, use the application. You can download
it from the Hitachi web site (http://www.hitachi-america.us/digitalmedia or http://

www.hitachidigitalmedia.com). For information on the necessary settings and
operations for the computer and projector, refer to the manual for the application.

NOTE

• It is possible to store the text data up to 12 in the maximum.

• Using MY BUTTON that registered MESSENGER can turn the displaying
messenger text on/off. (

• The text le also can be displayed by using schedule function via the web
browser. Refer to item 7.3 Event Scheduling (&59) for the detail.

• If data is transferred via wireless and wired LAN at the same time, the

projector may not be able to process the data correctly.

&OPTION menu in the Operating Guide)

52

6. Network Bridge Function

6. Network Bridge Function

This projector is equipped with the NETWORK BRIDGE function to perform

mutual conversion of a network protocol and a serial interface.

By making use of the NETWORK BRIDGE function, a computer that is connected
to the projector via wireless or wired LAN is able to control an external device via
RS-232C communication using the projector as a network terminal.

Protocol change

RS-232C

RS-232C cable

External device

CONTROL port

Computer

TCP/IP data Serial data

Wired LAN
LAN cable

Wireless

LAN

LAN port

USB TYPE A port

6.1 Connecting devices

1) Connect the projector’s LAN port to the computer’s LAN port with a LAN
cable, or insert the USB wireless adapter into the USB TYPE A port.

2) Connect the projector’s CONTROL port and the device’s RS-232C port with
an RS-232C cable, for RS-232C communication.

NOTE

to ensure the connection.
of each port and use the suitable cable. (
Operating Guide - Technical)

• Before connecting the devices, read the manuals for the devices
For RS-232C connection, check the specications

&Connection to the ports in the

53

6. Network Bridge Function

6.2 Communication setup

To congure the setup of the communication using NETWORK BRIDGE for
the projector, use items in the COMMUNICATION menu. Open the menu of
the projector and select the OPTION - SERVICE - COMMUNICATION menu.

(

&OPTION menu > SERVICE > COMMUNICATION in the Operating Guide)

1) In the COMMUNICATION TYPE menu, select NETWORK BRIDGE
(WIRELESS or WIRED depending on the type of connection you use) for the

CONTROL port.

2) Using the SERIAL SETTINGS menu, select the proper baud rate and parity

for the CONTROL port, according to the specication of the RS-232C port of
the connected device.

Item Condition

BAUD RATE 4800bps/9600bps/19200bps/38400bps

PARITY NONE/ODD/EVEN

Data length 8 bit (xed)

Start bit 1 bit (xed)

Stop bit 1 bit (xed)

3) Using the TRANSMISSION METHOD menu, set up the proper method for the

CONTROL port according to your use.

NOTE

• The OFF is selected for the COMMUNICATION TYPE as the default

setting.

• Using the COMMUNICATION menu, set up the communication. Remember

that an unsuitable setup could cause malfunction of communication.

• When either one of the NETWORK BRIDGE settings is selected in the
COMMUNICATION TYPE menu, RS-232C commands cannot be received from

the CONTROL port.

6.3 Communication port

For the NETWORK BRIDGE function, send the data from the computer to the

projector with using the Network Bridge Port that is congured in the Port
Settings of web browser. (

NOTE

• Except for 41794, 9715, 9716, 9719, 9720, 5900, 5500, 4352

between 1024 and 65535 can be set up as the Network Bridge Port number.
It is set to 9717 as the default setting.

&23)

54

6. Network Bridge Function

6.4 Transmission method

The transmission method can be selected from the menus, only when the

NETWORK BRIDGE is selected for the COMMUNICATION TYPE.

(

&OPTION menu > SERVICE > COMMUNICATION in the Operating Guide)

HALF-DUPLEX  FULL-DUPLEX

6.4.1 HALF-DUPLEX

This method lets the projector make two way communication, but only one
direction, either transmitting or receiving data, is allowed at a time.
The method does not allow the projector to receive the data from the computer
while waiting for response data from an external device. After the projector
receives the response data from an external device or the response limit time is
past, the projector can receive the data from the computer.
That means that the projector controls transmitting and receiving the data to

synchronize the communication.
To use the HALF-DUPLEX method, set up the RESPONSE LIMIT TIME following

the instructions below.

TCP/IP data Serial data

Wired LAN

LAN cable

Computer

Wireless LAN

Transmitting data

Discarding data

Response data

Protocol change

Transmitting data

Response limit

time

RS-232C

RS-232C cable

Response data

Transmitting data

External device

Using the RESPONSE LIMIT TIME menu, set the waiting time for response data

from an external device. (

&OPTION menu > SERVICE > COMMUNICATION

in the Operating Guide)

OFF  1s  2s  3s ( OFF)

55

6.4 Transmission method (continued)

6. Network Bridge Function

NOTE

• With using the HALF-DUPLEX method, the projector can send out

254 byte data as maximum at once.

• If it is not required to monitor the response data from an external device and
the RESPONSE LIMIT TIME is set to OFF, the projector can receive the data

from the computer and send it out to an external device continuously.
The OFF is selected as the default setting.

6.4.2 FULL-DUPLEX

This method lets the projector make two way communication, transmitting and
receiving data at the same time, without monitoring response data from an
external device.
With using this method, the computer and an external device will send the data

out of synchronization. If it is required to synchronize them, set the computer to
make the synchronization.

NOTE

• In case that the computer controls to synchronize transmitting

and receiving the data, it may not be able to control an external device well
depending on the processing status of the projector.

56

7. Other Functions

7. Other Functions

7.1 E-mail Alerts

The projector can automatically send an alert message to the specied e-mail
addresses when the projector detects a certain condition that is requiring

maintenance or detected an error.

NOTE

• The projector may be not able to send e-mail if the projector suddenly loses

power.

Mail Settings (

To use the projector’s e-mail alert function, please congure the following items

through a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select

Projector Web Control from the selection window.

2) Enter your user name and password, and then click the [OK].

3) Click the [Mail Settings] and congure each item. Refer to item 3.1.5 Mail
Settings (

4) Click the [Apply] button to save the settings.

NOTE

that the e-mail settings are correct. The following mail will be delivered to the
specied addresses.

Subject line :Test Mail <Projector name>
Text :Send Test Mail
Date <Testing date>

Time <Testing time>

IP Address <Projector IP address>
MAC Address <Projector MAC address>

• Up to ve e-mail addresses can be specied.

)

&24

&24) for further information.

• Click the [Send Test Mail] button in the [Mail Settings] to conrm

57

7. Other Functions

7.1 E-mail Alerts (continued)

5) Click the [Alert Settings] on the main menu to congure the E-mail Alerts

settings.

6) Select and congure each alert item. Refer to item 3.1.6 Alert Settings (
for further information.

7) Click the [Apply] button to save the settings.

Failure/Warning e-mails are formatted as follows:

Subject line : <Mail title> <Projector name>
Text : <Mail text>
Date <Failure/Warning date>
Time <Failure/Warning time>
IP Address <Projector IP address>
MAC Address <Projector MAC address>

&31)

58

7. Other Functions

7.2 Projector Management using SNMP

The SNMP (Simple Network Management Protocol) enables to manage the

projector information, which is a failure or warning status, from the computer on

the network. The SNMP management software will be required on the computer

to use this function.

NOTE

• It is recommended that SNMP functions be carried out by a network

administrator.

• SNMP management software must be installed on the computer to monitor
the projector via SNMP.

SNMP Settings (

&23

)

Congure the following items via a web browser to use SNMP.

Example: If the IP address of the projector is set to 192.168.1.10:

1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select

Projector Web Control from the selection window.

2) Enter your user name and password, and then click the [OK].

3) Click the [Port Settings] on the main menu.

4) Click the [Download MIB le] to download a MIB le.

NOTE

• To use the downloaded MIB le, specify the le by your SNMP

manager.

5) Click the [Enable] check box to open the SNMP Port. Set the IP address to
send the SNMP trap to when a Failure/Warning occurs.

NOTE

• A Network Restart is required after the SNMP Port conguration
settings have been changed. Click [Network Restart] on the main menu and
click the [Restart] button. Then congure the following items.

6) Click the [Security Settings] on the main menu.

7) Click the [SNMP] and set the community name on the screen that is displayed.

NOTE

• A Network Restart is required after the Community name has been
changed. Click [Network Restart] on the main menu and click the [Restart]
button. Then congure the following items.

8) Congure the settings for Trap transmission of Failures/Warnings. Click the
[Alert Settings] on the main menu and select the Failure/Warning item to be
congured.

9) Click the [Enable] check box to send out the SNMP trap for Failures/Warnings.
Clear the [Enable] check box when SNMP trap transmission is not required.

10) Click the [Apply] button to save the settings.

59

7. Other Functions

7.3 Event Scheduling

The scheduling function enables to setup scheduled events including power on /
power off. It enables to be “self-management” projector.

NOTE

My Image, Messenger, Slideshow. (

• You can schedule the following control events: Power, Input Source,

&28)

• The power on event has the lowest priority among the all events that are
dened at the same time.

• There are 3 types of Scheduling, 1) daily 2) weekly 3) specic date. (&27)

• The priority for scheduled events is as follows 1) specic date 2) weekly 3)

daily.

• Up to ve specic dates are available for scheduled events. Priority is given to

those with the lower numbers when more than one event has been scheduled

for the same date and time (e.g., ‘Specic date No. 1’ has priority over ‘Specic
date No. 2’ and so on.

• Be sure to set the date and time before enabling scheduled events. (&30)
Once you turn off the projector in the SAVING mode (&SETUP menu in the
Operating Guide) or the AC power, the current date and time setting is reset.

60

7. Other Functions

7.3 Event Scheduling(continued)

Schedule Settings (

&27

)

Schedule settings can be congured from a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select

Projector Web Control from the selection window.

2) Enter your user name and password, and then click the [OK].

3) Click the [Schedule Settings] on the main menu and select the required

schedule item. For example, if you want to perform the command every

Sunday, please select the [Sunday].

4) Click the [Enable] check box to enable scheduling.

5) Enter the date (month/day) for specic date scheduling.

6) Click the [Apply] button to save the settings.

7) After congure the time, command and parameters, click the [Register] to add

the new event.

8) Click the [Delete] button when you want to delete a schedule.

There are three types of scheduling.

1) Daily: Perform the specied operation at a specied time every day.

2) Sunday ~ Saturday: Perform the specied operation at the specied time on a
specied day of the week.

3) Specic date: Perform the specied operation on the specied date and time.

NOTE

• In standby mode, the POWER indicator will ash green for approx. 3

seconds when at least 1 “Power ON” schedule is saved.

• When the schedule function is used, the power cord must be connected to the

projector and the outlet. The schedule function does not work when the breaker
in a room is tripped. The power indicator will lights orange or green when the

projector is receiving AC power.

61

7.3 Event Scheduling(continued)

7. Other Functions

Date/Time Settings (

&30

)

The Date/Time setting can be adjusted via a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select

Projector Web Control from the selection window.

2) Enter your user name and password, and then click the [OK].

3) Click the [Date/Time Settings] on the main menu and congure each item.
Refer to item 3.1.8 Date/Time Settings (

&30) for further information.

4) Click the [Apply] button to save the settings.

NOTE

recommended to maintain accurate time (

• The internal clock’s time may not remain accurate. Using SNTP is

&31).

• Once you turn off the projector in the SAVING mode (&SETUP menu in the
Operating Guide) or the AC power, the current date and time setting is reset.

62

7. Other Functions

7.4 Command Control via the Network

You can congure and control the projector via the network using RS-232C

commands.

Communication Port

The following two ports are assigned for the command control.

TCP #23 (Network Control Port1 (Port: 23))
TCP #9715 (Network Control Port2 (Port: 9715))

NOTE

Command Control Settings (

• Command control is available only via the specied port above.

)

&22

Congure the following items from a web browser when command control is used.

Example: If the IP address of the projector is set to 192.168.1.10:

1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select

Projector Web Control from the selection window.

2) Enter your user name and password, and then click the [OK].

3) Click the [Port Settings] on the main menu.

4) Click the [Enable] check box to open Network Control Port1 (Port: 23) to use
TCP #23. Click the [Enable] check box for the [Authentication] setting when
authentication is required, otherwise clear the check box.

5) Click the [Enable] check box to open Network Control Port2 (Port: 9715) to
use TCP #9715. Click the [Enable] check box for the [Authentication] setting
when authentication is required, otherwise clear the check box.

6) Click the [Apply] button to save the settings.

63

7. Other Functions

7.4 Command Control via the Network (continued)

When the authentication setting is enabled, the following settings are required.
(

&32)

7) Click the [Security Settings] on the main menu.

8) Click the [Network Control] and enter the desired authentication password.
* See NOTE.

9) Click the [Apply] button to save the settings.

NOTE

• The Authentication Password will be the same for Network Control

Port1 (Port: 23), Network Control Port2 (Port: 9715), PJLink™ Port (Port:

4352), My Image Port (Port: 9716) and Messenger Port (Port: 9719).

• The new conguration settings are activated after restarting the network
connection. When the conguration settings are changed, you must restart
the network connection. You can restart the network connection from Network

Restart on the main menu(

&41).

64

7. Other Functions

7.4 Command Control via the Network (continued)

Command Format

Command formats differ among the different communication ports.

● TCP #23

You can use the RS-232C commands without any changes. The reply data
format is the same as the RS-232C commands. (

&RS-232C Communication

in the Operating Guide - Technical)

However, the following reply will be sent back in the event of authentication

failure when authentication is enabled.

<Reply in the event of an authentication error>

Reply Error code

0x1F 0x04 0x00

● TCP #9715

Send Data format

The following formatting is added to the header (0 x 02), Data length (0 x 0D),
Checksum (1 byte) and Connection ID (1 byte) of the RS-232C commands.

Header Data length RS-232Ccommand Check Sum

0x02 0x0D 13 bytes 1 byte 1 byte

Connection

ID

Header → 0x02, Fixed
Data length → RS-232C commands byte length (0x0D, Fixed)
RS-232C command → RS-232C commands that start with 0xBE 0xEF

(13 bytes)

Check Sum → This is the value to make zero on the addition of the

lower 8 bits from the header to the checksum.

Connection ID → Random value from 0 to 255 (This value is attached

to the reply data)

65

7. Other Functions

7.4 Command Control via the Network (continued)

Reply Data format

The connection ID (the data is same as the connection ID data on the sending
data format) is attached to the RS-232C commands reply data.

<ACK reply>

Reply

0x06 1 byte

Connection

<NAK reply>

Reply

0x15 1 byte

Connection

<Error reply>

Reply Error code

0x1C 2 bytes 1 byte

<Data reply>

Reply Data

0x1D 2 bytes 1 byte

<Projector busy reply>

Reply Status code

0x1F 2 bytes 1 byte

ID

ID

Connection

ID

Connection

ID

Connection

ID

<Authentication error reply>

Reply

0x1F 0x04 0x00 1 byte

Authentication

Error code

Connection

ID

66

7. Other Functions

7.4 Command Control via the Network (continued)

Automatic Connection Break

The TCP connection will be automatically disconnected after there is no

communication for 30 seconds after being established.

Authentication

The projector does not accept commands without authentication success
when authentication is enabled. The projector uses a challenge response type

authentication with an MD5 (Message Digest 5) algorithm.
When the projector is using a LAN, a random 8 bytes will be returned if
authentication is enabled. Bind this received 8 bytes and the Authentication
Password and digest this data with the MD5 algorithm and add this in front of the

commands to send.

Following is a sample if the Authentication Password is set to “password” and the

random 8 bytes are “a572f60c”.

1) Connect the projector.

2) Receive the random 8 bytes “a572f60c” from the projector.

3) Bind the random 8 bytes “a572f60c” and the Authentication Password

“password” and it becomes “a572f60cpassword”.

4) Digest this bind “a572f60cpassword” with MD5 algorithm.

It will be “e3d97429adffa11bce1f7275813d4bde”.

5) Add this “e3d97429adffa11bce1f7275813d4bde” in front of the commands
and send the data.

Send “e3d97429adffa11bce1f7275813d4bde”+command.

6) When the sending data is correct, the command will be performed and the

reply data will be returned. Otherwise, an authentication error will be returned.

NOTE

• As for the transmission of the second or subsequent commands, the

authentication data can be omitted when the same connection.

67

7. Other Functions

7.5 Crestron RoomView

®

Crestron RoomView® is a multi-user resource management program provided
by Crestron Electronics, Inc. It is an application for managing and controlling the

projector and other AV devices collectively.

For details of Crestron RoomView®, refer to the Crestron® website.

URL: http://www.crestron.com (as of Aug. 2011)

The following communication interfaces can be used to manage the entire facility.

1) Crestron RoomView

®

Express / Crestron RoomView® Server Edition
RoomViewTM Express and RoomViewTM Server Edition are software provided
by Crestron Electronics, Inc. They are used for managing all the AV devices,

and are also able to communicate with the help desk as well as send out alert
messages.
For details of the software, refer to the following website.

URL: http://www.crestron.com/getroomview

2) Crestron e-Control

®

Crestron e-Control® is a system controller that can be operated via a web

browser (

&42

).

68

8. Troubleshooting

8. Troubleshooting

Problem Likely Cause Things to Check

• Bring the computer and

projector closer together.

• Radio waves won’t go

through concrete and metal
(steel doors, etc.)

If there is a wireless

conguration utility loaded

on your computer, check its
settings.

Please refer the manual of
your conguration utility.

Check the network

configurations of the
computer and projector.

Change the network address

setting for wireless or wired

LAN.

Insert the optional USB

wireless adapter.

Try changing of SSID and IP

Address.

Try “NETWORK RESTART”
in SERVICE menu under the
NETWORK menu.

Can't communicate

Others

- Information from

the projector
to computer is
not correct or
completed

- The projector does

not respond

Weak radio signal

Cannot communicate due
to congure wireless /

encryption settings.

The computer and/or

projector's network settings

are not congured correctly.

The same network address
is set for both wireless and

wired LAN.

<Only for wireless LAN>
The USB wireless adapter

is not inserted into the
projector.

<Only for wireless LAN>

There is closely another
projector or other that has
the same wireless setting.

Communication between the

projector and computer is not
working well.

NETWORK Functions of the

projector is not working well.

Reference

Page

Number

–

–

–

20,

21

–

20

In the

Operating

Guide

69

9. Specications

9. Specications

Item Specifications

Control software Dedicated computer application and Web browser

Corresponding
protocol

Network

Security

Computer
application's system
requirements

USB wireless adapter Gemtek USB-Link11n

TCP/IP, DHCP client and HTTP server

Wireless LAN (IEEE802.11b/g/n)

(Ad-Hoc and Infrastructure modes)

Wired LAN(100Base-TX/10Base-T)

WEP (64/128bit), WPA-PSK (TKIP/AES),

WPA2-PSK (TKIP/AES), SSID

OS: Windows

Windows
Windows Vista
Windows Vista
Windows Vista
Windows Vista
Windows Vista
Windows
Windows
Windows
Windows
Windows
Windows

®

XP Home

®

XP Professional

®

Home Basic

®

Home Premium

®

Business

®

Ultimate

®

Enterprise

®

7 Starter

®

7 Home Basic

®

7 Home Premium

®

7 Professional

®

7 Ultimate

®

7 Enterprise

CPU: Pentium 4 (2.8 GHz or higher)

Graphic card: 16 bit, XGA or higher

Memory: 512 MB or higher

Hard disk space: 100 MB or higher

Web browser: Internet Explorer

®

6.0 or higher

CD-ROM/DVD-ROM drive

10. Warranty and after-sales service

10. Warranty and after-sales service

If a problem occurs with the equipment, please read 8. Troubleshooting (&68)
section rst and review all suggested check points. After that, please contact your

dealer or service company, if you still have the problem. They will tell you what
warranty condition is applied.

70