Crestron MMK-15L & WMKM-15L
Mud Mount Kits
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2005 Crestron Electronics, Inc.
Crestron MMK-15L & WMKM-15L Mud Mount Kits
Mud Mount Kits: MMK-15L &
WMKM-15L
Description
When cutouts made in the drywall for touchpanel installation are too large, Mud
Mount Kits are the preferred mounting option for the Crestron Isys
TPS-15G-L series of wall mounted touchpanels as well as the Isys i/O™
TPMC-15-QM-L and TPMC-15-CH-L series of wall mounted touchpanels. These
kits provide support for additional plastering that can be applied to hide large
irregularities in the touchpanel cutout.
NOTE: If mounting into another material (other than drywall – for example, wood
lectern, concrete, or rock) use the mounting plate, available in the post-construction
kit WMKM-15 as a hole cutout template. For concrete and rock mounting material,
allow for proper ventilation before mounting the touchpanel.
There are two Mud Mount Kits. The MMK-15L is a pre-construction accessory. Preconstruction refers to framed walls prior to hanging drywall. This accessory must be
used with either the Pre-Construction Mount Kit (PMK-15L) or Back Box Kit
(BB-15L).
The WMKM-15L is a post-construction kit. Post-construction refers to framed walls
with drywall hung. This accessory is designed with a mounting plate so that it can be
placed anywhere on a wall without the support from a stud.
NOTE: If necessary, consult the latest revision of the TPS-12L/15L/17L Operations
Guide (Doc. 6355), the TPS-12G/15G-L Operations Guide (Doc. 6356), or the
TPMC-15/17-L Series Operations Guide (Doc. 6354) for a complete list of mounting
options.
®
TPS-15L and
Supplied Hardware
The MMK-15L consists of three parts. These parts produce an assembly that attaches
to the PMK-15L or BB-15L. The WMKM-15L consists of the same three parts that
make up the MMK-15L as well as one mounting plate. The mounting plate is the
part that provides the necessary support for post-construction applications.
Installation Guide – DOC. 6364 Mud Mount Kits: MMK-15L & WMKM-15L • 1
Mud Mount Kits Crestron MMK-15L & WMKM-15L
Supplied Hardware of the MMK-15L and WMKM-15L
DESCRIPTION PART NUMBER QUANTITY
Metal Plate, Mounting
(WMKM-15L only)
Metal Plate, Mud Ring 2013005 1
Metal Plate, Fastener 2004825 2
Hardware, Push-On Fastener 2004121 4
Dimensional Drawings
2012920 1
(35.02 cm)
14.19 in
(36.05 cm)
MOUNTING PLATE FOR
WMKM-15L
Drywall Cutout Dimensions
13.79 in
0.06 in
(0.15 cm)
14.13 in
(35.88 cm)
(5.73 cm)
2.26 in
(14.99 cm)
0.38 in
(0.95 cm)
FASTENER PLATE FOR
WMKM-15L & MMK-15L
5.90 in
0.38 in
(0.95 cm)
14.80 in
(37.59 cm)
MUD RING PLATE FOR
WMKM-15L & MMK-15L
NOTE: The inside edge of the mounting plate can be used as a cutout template.
7
~13
in
64
(333 mm Max)
DO NOT EXCEED
THIS DIMENSION
61
in
~12
64
(329 mm Max)
3
in
~12
4
(324 mm Max)
5
~
in
64
3
~
16
(2 mm Max)
in
5
~1
in
64
(28 mm Max)
TYP (4X)
21
~3
in
32
(93 mm Max)
13
~6
in
64
(158 mm Max)
1
~13
in
2
3
in
Ø ~
16
(5 mm Max)
TYP (4X)
(5 mm Max)
(343 mm Max)
DO NOT EXCEED
THIS DIMENSION
2 • Mud Mount Kits: MMK-15L & WMKM-15L Installation Guide – DOC. 6364
Crestron MMK-15L & WMKM-15L Mud Mount Kits
Installation
This section provides an installation procedure for each Mud Mount Kit. The
procedure for the MMK-15L starts below and the “WMKM-15L Procedure” starts
on page 5.
MMK-15L Procedure
The procedure in this section provides the necessary steps for the assembly of the
MMK-15L to either the PMK-15L or BB-15L. It is assumed that the PMK-15L or
BB-15L has been secured to the stud according to the procedures in the latest
revisions of their respective Installation Guides (Doc. 6363 and Doc. 6362,
respectively). Also, it is assumed that drywall is in place and a rectangular cutout for
the touchpanel is made in the drywall (refer to the Drywall Cutout dimensions on
page 2 for cutout dimensions).
Complete the steps in the order provided. The only tools or materials required and
not supplied are a drywall saw or equivalent, four standard drywall screws, #2
Phillips screwdriver, a level, and tools/material to apply drywall joint compound.
CAUTION: Allow an air gap of at least 12 inches in the wall cavity above the
touchpanel for heat dissipation.
NOTE: The illustrations in this procedure show the installation of the MMK-15L
with the PMK-15L. Even though the illustrations only show the PMK-15L, they are
identical for the BB-15L as well.
1. Pass a fastener plate through the opening and align its two center holes
with the top two pins on the PMK-15L. Verify that the pins on the
fastener plate are not between the fastener plate and the PMK-15L.
Refer to the illustration after this step for visual guidance.
Secure Fastener Plates to PMK-15L (or BB-15L)
PMK-15L
(4) PUSH-ON FASTENER
(2004121)
(2) FASTENER PLATE
(2004825)
2. Slide a push-on fastener over each pin of the PMK-15L (or
BB-15L) to loosely secure the fastener plate and the mounting plate.
Installation Guide – DOC. 6364 Mud Mount Kits: MMK-15L & WMKM-15L
• 3
Mud Mount Kits Crestron MMK-15L & WMKM-15L
Do not push the push-on fasteners all the way down onto the pins. Slide
them on enough to keep the fastener plate and mounting plate as one
fastener/mounting plate assembly.
3. Use the second fastener plate and repeat steps 1 and 2 using the lower
two PMK-15L (or BB-15L) pins.
NOTE: When installing into the PMK-15L, verify that the 18 AWG bus wire
securing the cables for the touchpanel remain attached.
4. Verify that the drywall cutout meets the measurements specified on
page 2.
5. Insert the symmetrical mud ring plate into the opening, as shown in the
illustration after this step.
Insert and Secure Mud Ring Plate into PMK-15L (or BB-15L)
PMK-15L
DRYWALL
FLANGE
HOLES FOR DRYWALL SCREWS
(PROVIDED BY OTHER) SCREW
LENGTH SHOULD NOT EXCEED
DRYWALL THICKNESS BY
MORE THAN 1/2".
MUD RING PLATE
(2013005)
6. When the mud ring plate is in position, bend the top two flanges of the
plate upward and the bottom two flanges downward.
• If mounting into the PMK-15L, bend the flanges approximately
90 degrees.
• If mounting into the BB-15L, bend the flanges back as far as they
can go.
7. Use four standard drywall screws (length should not exceed drywall
thickness by more than ½ inch) to secure the mud ring plate to the rest
of the assembly. The screws pass through the clearance holes in the
PMK-15L (or BB-15L) and are secured in the extruded holes of the
fastener plates.
8. Verify that the mud ring plate is level.
NOTE: Do not over tighten screws. Doing so may over-dimple or rip the mud ring
plate.
9. Use a #2 Phillips screwdriver and tighten the drywall screws by hand
so that they slightly dimple into the holes in the mud ring plate.
10. Apply drywall joint compound as needed to finish the cutout. Avoid
covering the four tapped mounting holes.
• Mud Mount Kits: MMK-15L & WMKM-15L Installation Guide – DOC. 6364
4
Crestron MMK-15L & WMKM-15L Mud Mount Kits
11. Run the necessary cables for the touchpanel and secure them behind the
drywall.
12. When dry, the touchpanel can be installed using the four tapped holes
in the PMK-15L. Refer to the latest revision of the
TPS-12L/15L/17L Operations Guide (Doc. 6355), the TPS-12G/15G-L
Operations Guide (Doc. 6356), or the TPMC-15/17-L Series
Operations Guide (Doc. 6354) for installation instructions.
WMKM-15L Procedure
The procedure in this section provides the necessary steps for the assembly and
installation of the WMKM-15L into a wall. Complete the steps in the order provided.
The only tools or materials required and not supplied are a drywall saw or
equivalent, a level, four standard drywall screws, #2 Phillips screwdriver, and
tools/material to apply drywall joint compound.
CAUTION: Allow an air gap of at least 12 inches in the wall cavity above the
touchpanel for heat dissipation.
1. Insert the two pins on one fastener plate into the top two outer holes on
the mounting plate, as shown in the following illustration.
Create the Fastener/Mounting Plate Assembly
(1) MOUNTING PLATE
(2012920)
(2) FASTENER PLATE
(2004825)
(4)PUSH-ON FASTENER
(2004121)
2. Slide a push-on fastener over each pin on the fastener plate to loosely
secure the fastener plate and the mounting plate. Do not push the pushon fasteners all the way down onto the pins. Slide them on enough to
keep the fastener plate and mounting plate as one fastener/mounting
plate assembly.
3. Use the second fastener plate and repeat steps 1 and 2 using the lower
two PMK-15L pins.
4. Locate an area on the wall that is free of miscellaneous wiring and
studs.
5. Make a small hole near the middle of the designated site; verify that the
location is suitable.
NOTE: Make the cutout as level as possible. The mounting plate allows for only
minor leveling adjustments.
Installation Guide – DOC. 6364 Mud Mount Kits: MMK-15L & WMKM-15L
• 5
Mud Mount Kits Crestron MMK-15L & WMKM-15L
6. Use the drywall saw or equivalent to produce a level, rectangular cutout
in the drywall as shown on page 2.
7. Insert the symmetrical mud ring plate into the opening, as shown in the
illustration after this step.
Insert the Mud Ring Plate into the Opening
IMPORTANT
PLEASE MAKE DRYWALL CUTOUT AS
LEVEL AND CLEAN AS POSSIBLE.
THE MOUNTING PLATE ALLOWS FOR ONLY
FLANGE
HOLES FOR DRYWALL SCREWS
(PROVIDED BY OTHER) SCREW
LENGTH SHOULD NOT EXCEED
DRYWALL THICKNESS BY
MORE THAN 1/2".
MINOR ADJUSTMENT OF THE TOUCHPANEL.
MUD RING PLATE
(2013005)
8. Carefully pass the fastener/mounting plate assembly through the
opening and rest the assembly against the interior surface of the
drywall. Verify that the fastener plates are between the mounting plate
and the drywall.
9. When the fastener/mounting plate assembly is in position, bend the top
two flanges of the mud ring upward (approximately 90 degrees) and the
bottom two flanges downward (approximately 90 degrees). Refer to the
illustration after this step.
NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It
allows for minor adjustments to the touchpanel during installation.
Bend Flanges
• Mud Mount Kits: MMK-15L & WMKM-15L Installation Guide – DOC. 6364
6
Crestron MMK-15L & WMKM-15L Mud Mount Kits
10. Use four standard drywall screws (of adequate length) to secure the
plate to the fastener/mounting plate assembly. The screws pass through
the clearance holes in the plate and are secured in the extruded holes of
the fastener plates.
11. Verify that the plate is level before tightening.
NOTE: Do not over tighten screws. Doing so may over-dimple or rip the plate.
12. Use a #2 Phillips screwdriver and tighten the drywall screws by hand
so that they slightly dimple into the holes in the mud ring plate.
13. Run the necessary cables for the touchpanel and secure them behind the
drywall.
14. Apply drywall joint compound as needed to finish the cutout. Avoid
covering the four tapped mounting holes.
15. When dry, the touchpanel can be installed using the four tapped holes
in the mounting plate. Refer to the latest revision of the
TPS-12L/15L/17L Operations Guide (Doc. 6355), the TPS-12G/15G-L
Operations Guide (Doc. 6356), or the TPMC-15/17-L Series
Operations Guide (Doc. 6354) for details.
Further Inquiries
Future Updates
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876].
For assistance in your local time zone, refer to the Crestron website
(www.crestron.com) for a listing of Crestron worldwide offices.
You can also log onto the online help section of the Crestron website to ask
questions about Crestron products. First-time users will need to establish a user
account to fully benefit from all available features.
As of the date of manufacture, the MMK-15L and WMKM-15L have been tested
and found to comply with specifications for CE marking.
As Crestron adds improvements to the MMK-15L or WMKM-15L, additional
information may be made available as manual updates. These updates are solely
electronic and serve as intermediary supplements prior to the release of a complete
technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
Installation Guide – DOC. 6364 Mud Mount Kits: MMK-15L & WMKM-15L
• 7
Mud Mount Kits Crestron MMK-15L & WMKM-15L
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange, or service without prior
authorization from CRESTRON. To obtain warranty service for CRESTRON
products, contact the factory and request an RMA (Return Merchandise
Authorization) number. Enclose a note specifying the nature of the problem, name
and phone number of contact person, RMA number, and return address.
2. Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped
freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J., or its authorized
subsidiaries, with RMA number clearly marked on the outside of all cartons.
Shipments arriving freight collect or without an RMA number shall be subject to
refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a
15% restocking fee, plus shipping costs, on any products returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by
CRESTRON, shipping by standard ground carrier. In the event repairs are found to
be non-warranty, return freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in
materials and workmanship under normal use for a period of three (3) years from the date of
purchase from CRESTRON, with the following exceptions: disk drives and any other moving or
rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1)
year; touchscreen display and overlay components are covered for 90 days; batteries and
incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized
CRESTRON dealer. Purchasers should inquire of the dealer regarding the nature and extent of the
dealer's warranty, if any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in
any application other than that for which it was intended, or if it has been subjected to misuse,
accidental damage, modification, or improper installation procedures. Furthermore, this warranty
does not cover any product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic
damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for
any claim made by a third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for
parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be
covered only by the unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed
or implied, nor authorizes any other party to offer any warranty, including any implied warranties
of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed
by law are limited to the terms of this limited warranty. This warranty statement supercedes all
previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered
trademark of Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft
Corporation.
• Mud Mount Kits: MMK-15L & WMKM-15L Installation Guide – DOC. 6364
8
Crestron MMK-15L & WMKM-15L Mud Mount Kits
This page intentionally left blank.
Installation Guide – DOC. 6364 Mud Mount Kits: MMK-15L & WMKM-15L
• 9
Crestron Electronics, Inc. Installation Guide – DOC. 6364
15 Volvo Drive Rockleigh, NJ 07647 (2013140)
Tel: 888.CRESTRON 07.05
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Loading...