Crestron WMKM-1000L Operating Manual

Crestron MMK-1000L & WMKM-1000L
Mud Mount Kits
Installation Guide

This document was prepared and written by the Technical Documentation department at:

Crestron Electronics, Inc.

15 Volvo Drive

Rockleigh, NJ 07647

1-888-CRESTRON

All brand names, product names and trademarks are the property of their respective owners.

©2002 Crestron Electronics, Inc.

Crestron MMK-1000L & WMKM-1000L Mud Mount Kits

Mud Mount Kits: MMK-1000L &
WMKM-1000L

Description

Mud Mount Kits are the preferred mounting option for the Series 1000 wall mounted
touchpanels when cutouts made for the touchpanel are too large. These kits fill in the
gaps with additional plastering and provide the support to hide large irregularities in
the touchpanel cutout.

There are two Mud Mount Kits. The MMK-1000L is a pre-construction accessory.
Pre-construction refers to framed walls prior to hanging drywall. This accessory is
designed for use with the Pre-Construction Mount Kit (PMK-1000L) or Back Box
Kit (BB-1000L).

The WMKM-1000L is a post-construction kit. Post-construction refers to framed
walls with drywall hung. This accessory is designed with a mounting plate so that it
can be placed anywhere on a wall without the support from a stud.

NOTE: If necessary, consult the latest revision of the Series 1000 Operations Guide
(Doc. 5813) for a complete list of mounting options.

Supplied Hardware

The MMK-1000L consists of three parts. These parts produce an assembly that
attaches to the PMK-1000L or BB-1000L. The WMKM-1000L consists of the same
three parts that make up the MMK-1000L as well as one mounting plate. The
mounting plate is the part that provides the necessary support for post-construction
applications.

Supplied Hardware of the MMK-1000L and WMKM-1000L

DESCRIPTION PART NUMBER QUANTITY

Metal Plate, Mounting

(WMKM-1000L only)

Metal Plate, Mud Ring MTPL02835-1 1

Metal Plate, Fastener MTPL02833-1 2

Hardware, Push-On Fastener MMHO-11 4

MTPL02832-1 1

Installation Guide – DOC. 6062 Mud Mount Kits: MMK-1000L & WMKM-1000L • 1

Mud Mount Kits Crestron MMK-1000L & WMKM-1000L

Installation

This section provides an installation procedure for each Mud Mount Kit. The
procedure for the MMK-1000L starts below and the “WMKM-1000L Procedure”
starts on page 4.

MMK-1000L Procedure

The procedure in this section provides the necessary steps for the assembly of the
MMK-1000L to either the PMK-1000L or BB-1000L. It is assumed that the
PMK-1000L or BB-1000L has been secured to the stud according to the procedures
in the latest revisions of their respective Installation Guides (Doc. 6061 and Doc.
6060, respectively). Also, it is assumed that drywall is in place and a square cutout
for the touchpanel is made in the drywall measuring 4½ inches wide (114 mm) x 4½
inches high (114 mm).

Complete the steps in the order provided. The only tools or materials required and
not supplied are a drywall saw or equivalent, four standard drywall screws, #2
Phillips screwdriver, a level, and tools/material to apply drywall joint compound.

NOTE: The illustrations in this procedure show the installation of the MMK-1000L
with the PMK-1000L. Even though the illustrations only show the PMK-1000L, they
are identical for the BB-1000L as well.

1. Pass a fastener plate through the opening and align its two center holes
with the top two pins on the PMK-1000L. Verify that the pins on the
fastener plate are not between the fastener plate and the PMK-1000L.
Refer to the illustration after this step for visual guidance.

Secure Fastener Plates to PMK-1000L (or BB-1000L)

PMK-1000L

PUSH-ON FASTENER
QTY.4

FASTENER PLATE
QTY.2

• Mud Mount Kits: MMK-1000L & WMKM-1000L Installation Guide – DOC. 6062

2