Page 1
3.90 in.
Attach feet here
Drill one of these two holes Cutout for soundbar cables
Center reference hole
Drill one of these two holes
UC-SB1 and UC-SB1-CAM
UC Video Conference Smart Soundbars
Crestron® UC Video Conference Smart Soundbars (UC-SB1 and UC-SB1-CAM) are designed to provide speakerphone capabilities for use in a Bring
Your Own Device (BYOD) small to medium-sized meeting space. The soundbars feature a built-in microphone, speakers, and camera (UC-SB1-CAM
only).
NOTE: With the exception of the integrated camera, the UC-SB1 and UC-SB1-CAM have similar features. For simplicity within this guide, the term
“soundbar” is used for both models except where noted.
Check the Box
Item Qty
UC-SB1 and UC-SB1-CAM 1
Anchor, Drywall, Plastic, 3/8 in. x 1/2 in. (P/N 2052565) 4
Cable, USB 3.0, A - B, 6 ft (1.83 m) (P/N 2053077) 1
Foot, 2.3 in. x 0.96 in. x 0.15 in., Rubber (P/N 2052169) 2
Key, Anchor (P/N 4529654) 1
Power Cord (P/N 2052498) 1
Screw, 8-AB x 1-1/2 in., Pan Head, Combo (P/N 2052567) 4
Template, Overlay (P/N 4529513) 1
Install the Soundbar
The soundbar can be placed on a flat surface or mounted on a wall. The soundbar has the following dimensions:
Dimensions (UC-SB1-CAM shown)
Mount on a Wall
The soundbar includes anchors that are suitable for use on sheetrock walls up to 1/2 in. thickness. Masonr y and other materials may require
additional installer-supplied mounting hardware.
NOTES:
• For optimal viewing results, the UC-SB1-CAM should be mounted in a location that places the camera approximately 12 in. above the plane of
the room’s conference table.
• When mounting on a wall beneath a display device, leave 3/4 in. (minimum) clearance above the top of the soundbar. Use the included
template to allow for sufficient clearance between the soundbar and display device.
The following tools are required to mount the soundbar:
• Dr ywall saw (not included)
• Drill with 5/16 in. bit (not included)
To mount the soundbar on a wall:
1. The included template provides drill hole locations for the wall mount hardware. Using the center reference hole of the template as a guide,
attach the template to the desired mounting location with the center reference line of the template at the center of the desired location.
NOTE: The cutout in the center of the template should provide adequate access for all of the required cabling.
(99 mm)
43.60 in.
(1107 mm)
4.57 in.
(116 mm)
Place on a Flat Surface
If placing the soundbar on a flat surface, attach the included rubber feet to the bottom of the soundbar as shown in the following diagram.
Attach Rubber Feet (UC-SB1 shown)
2. Drill two pilot holes on each side of the center reference line as shown in the diagram above. Each side should have one pilot hole drilled in
3. Use a dry wall saw to make a cutout for the soundbar cables.
4. Install the four included anchors into the drilled pilot holes.
Drill one of these two holes
each row of the template.
a. Fold the anchor in the middle and pinch the ends together.
b. Insert the anchor in the hole and tap flush with the wall.
Center reference line
Drill one of these two holes
c. Insert the included anchor key to pop the anchor open and lock
it behind a hollow wall.
WARNING: Do not force or hammer the key.
d. Drive the screw part of the way into the anchor, leaving
approximately 1/4 in. of the screw exposed.
e. Repeat steps a through d for the other 3 anchors.
Page 2
5. Pivot the soundbar away from the wall bracket.
100-240V~, 0.5A, 50/60Hz
PC
(Pre-connected on UC-SB1-CAM)
Volume on
Microphone muted
Microphone and speaker muted
Pivot the Soundbar
Wall bracket
Soundbar
7. Route the cables through the cable cutout, and connect the cables
as described in “Hardware Hookup.”
NOTE: The included power cord is typically routed from the wall
opening, through the cable cutout, and to the soundbar.
Connect the Device
Make the necessary connections as called out in the following diagram.
Connect power last.
Soundbar, Rear Panel Connections
Audio and video to PC
From AC power outlet
Complete the Installation
Once all connections are made, pivot the soundbar up to the wall
bracket until the soundbar locks into place.
Operation
Status
The front panel status bar illuminates to provide operational
information.
• A green status bar indicates the volume level. Increasing the
volume increases the illumination. Decreasing the volume
decreases the illumination. When the volume = “0”, the status bar
is dark.
• Muting the microphone turns the center of the status bar
red. Muting the microphone and speaker turns the two outer
segments of the status bar red.
System Control
Each soundbar can be used in a BYOD scenario where the soundbar is
connected to an end-user’s PC over USB. The soundbar will pass both
camera and bi-directional (mic and speaker) audio across a single USB
connection.
NOTE: The UC-SB1 supports USB 2.0 and USB 3.0 speeds while the
UC-SB1-CAM supports only USB 3.0 speeds.
For Additional Information
Scan or click the QR code for detailed product information.
UC-SB1 UC-SB1-CAM
6. Place the wall bracket over the screws, and hand tighten the
screws until the wall bracket is secured to the wall.
Place and Secure the Wall Bracket
8-AB x 1-1/2 in. screws (x4)
Wall bracket
Soundbar
CAMERA
From USB camera
AUDIO IN and OUT
Line-level audio input and output
• PC: Connect the included USB cable to the PC port and a USB
port on the PC.
• CAMERA: Connect a USB camera (sold separately) to the
CAMERA port.
NOTE: On the UC-SB1-CAM, the integrated camera is already
connected from the factory.
• 100-240V~ 0.5A, 50/60Hz: Connect the included power cord to
the 100-240V~, 0.5A, 50/60Hz power input and an AC power
outlet.
The soundbar also provides unbalanced, stereo analog input and
output jacks (AUDIO IN and OUT, 3.5 mm TRS mini-phone). The
input accommodates a line-level audio source, which feeds to the
internal amplifier and speakers with no volume control or other signal
processing. The output can feed an assistive listening system, and
carries the same audio signal as the soundbar speakers.
Compliance and Legal
Original Instructions: The U. S. English vers ion of this docum ent is th e original instructions. All other langu ages are a transl ation
of the original instructions.
Regulatory Model: UC-SB
As of the date of manufac ture, th e produ ct has b een tes ted and fo und to com ply with specificat ions for CE marking.
This pro duct i s listed to appli cable UL® Standards and re quirem ents tested by I ntertek® servi ces.
Ce produ it est homolo gué sel on les no rmes et l es exigences UL applicables par Inter tek Pres tations de service .
Federal Communications Commission (FCC) Compliance Statement
This dev ice comp lies wi th par t 15 of the F CC Rules . Operation is s ubjec t to the fo llowing conditions: (1) This device may not
cause ha rmful interfe rence an d (2) this device must acce pt any inte rfere nce rece ived, i ncludi ng inter feren ce that m ay cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the
user’s a uthor ity to operate t he equipment .
NOTE: This e quipm ent has b een tes ted and fo und to com ply with the lim its for a Class A digital device, pursuant to part 1 5
of the FCC Rules. T hese li mits are designed to provide reasonable protection again st harmful inte rfere nce in a res idential
instal latio n. This e quipm ent generates , uses an d can radiate radio f requency energy and , if not installe d and use d in
accorda nce with the ins truc tions , may cause harmful inter ference to radio co mmunications. However, there is no g uarantee
that int erference will not occur in a par ticul ar installati on. If th is equipment do es cause harmfu l inter ference to radio or
televi sion reception, which can be determine d by turning the eq uipment off an d on, the u ser is en courag ed to tr y to corre ct the
inter ference by one or mo re of the fo llowing measures:
• Reori ent or rel ocate the recei ving antenna.
• Increase the separation between the equipment and receiver.
• Conne ct the equipm ent into an outlet on a circuit different fro m that to w hich the receiver is conn ected.
• Consu lt the de aler or a n experienced radio/ TV te chnician for hel p.
Industry Canada (IC) Compliance Statement
CAN ICE S-3 (B)/N MB-3(B)
The product wa rrant y can be fou nd at ww w.crestron.com/warrant y.
The spe cific p atent s that cover Cres tron pro duct s are lis ted at www.crestron.com/legal/patents.
Certa in Crestron pro duct s contain open so urce sof twar e. For specific information , pleas e visit w ww.crestron.com/opensource.
Crestron and th e Crestron logo are eith er trademarks or regis tered t radem arks of Cr estro n Elec tronic s, Inc . in the United
States an d/or other countri es. Intertek i s eithe r a trademark or re giste red trademark o f Inter tek Group in the United States
and/or other countries. T he ETL l ogo is ei ther a trademark or regi stere d trademark of Interte k Testing Servi ces NA in the Unite d
States an d/or other countri es. UL is either a tradem ark or re gistered trad emark of Under writers Laboratories, In c. in the United
States an d/or other countri es. Ot her trademarks, reg istered trademarks, and trade names may be u sed in th is document to
refer to ei ther the entit ies claiming th e marks and name s or their products . Crestron disclaims any proprietary interes t in the
marks and names of others. Crestron is not responsible for errors in typography or photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Dr ive, Roc kleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Do c. 8417C
Specifications subject to
change without notice.
(2052941)
05.19
Loading...