Page 1
Crestron TSW-RMB
Retrofit Mounting Brackets
for TSW-750 & TSW-1050
Installation Guide
Page 2
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or
their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or
photography.
This document was written by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
Page 3
Crestron TSW-RMB Retrofit Mounting Brackets for TSW-750 & TSW-1050
Contents
Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB 1
Introduction ............................................................................................................................... 1
Physical Description .................................................................................................... 2
Setup .......................................................................................................................................... 7
Supplied Hardware ...................................................................................................... 7
Installation ................................................................................................................... 8
Resources ................................................................................................................................. 10
Further Inquiries ........................................................................................................ 10
Future Updates .......................................................................................................... 10
Return and Warranty Policies .................................................................................................. 11
Merchandise Returns / Repair Service ...................................................................... 11
Crestron Limited Warranty ........................................................................................ 11
Installation Guide – DOC. 7609A Contents • i
Page 4
Page 5
Crestron TSW-RMB Retrofit Mounting Brackets for TSW-750 & TSW-1050
TSW-750-RMB-1
Retrofit Mounting Bracket – APAD, CT/LC-1000, or TPS-2000L to TSW-750
TSW-750-RMB-2
Retrofit Mounting Bracket – TPS-4L to TSW-750
TSW-1050-RMB-3
Retrofit Mounting Bracket – APAD, CT/LC-1000, TPS-2000L, or TPS-4L to TSW-1050
TSW-1050-RMB-4
Retrofit Mounting Bracket – TPS-6L to TSW-1050
TSW-1050-RMB-5
Retrofit Mounting Bracket – TPS-3100L to TSW-1050
Retrofit Mounting Brackets for
TSW-750 & TSW-1050: TSW-RMB
Introduction
Replacing an existing wall-mounted Crestron® touch screen with a new TSW-750 or
TSW-1050 touch screen is simplified using a TSW-RMB Retrofit Mounting Bracket.
A complete set of brackets is available to streamline the process without having to
tear up or patch the wall surface. The TSW-RMB simply mounts over the existing
back box, mounting kit, or cutout to accommodate the new touch screen.
TSW-RMB brackets are composed of metal and coated with a white, paintable
surface treatment.
NOTE: When mounting a TSW-750 using a TSW-RMB bracket, the top and
bottom edges of the bracket will be slightly visible.
Available Models
MODEL NUMBER DESCRIPTION
The TSW-750-RMB-1, TSW-750-RMB-2, TSW-1050-RMB-3, TSW-1050-RMB-4,
and TSW-1050-RMB-5 are functionally identical. For simplicity within this guide,
the term “TSW-RMB” is used except where noted.
Installation Guide – DOC. 7609A Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB • 1
Page 6
Retrofit Mounting Brackets for TSW-750 & TSW-1050 Crestron TSW-RMB
APAD
TSW-750
TSW-750-RMB-1
TSW-1050
TSW-1050-RMB-3
CT-1000 or LC-1000
TSW-750
TSW-750-RMB-1
TSW-1050
TSW-1050-RMB-3
TPS-2000L
TSW-750
TSW-750-RMB-1
TSW-1050
TSW-1050-RMB-3
TPS-3100L
TSW-1050
TSW-1050-RMB-5
TPS-4L
TSW-750
TSW-750-RMB-2
TSW-1050
TSW-1050-RMB-3
TPS-6L
TSW-1050
TSW-1050-RMB-4
1.36 in
(35 mm)
6.73 in
(171 mm)
3.74 in
(95 mm)
5.65 in
(144 mm)
4.80 in
(122 mm)
3.95 in
(101 mm)
TPS-2000L Mounting Hole
CT/LC-1000, APAD Mounting Hole
Choose the appropriate retrofit mounting bracket by using the following table.
EXISTING TOUCH SCREEN NEW TOUCH SCREEN RETROFIT MOUNTING BRACKET
Physical Description
TSW-750-RMB-1 Overall Dimensions (Top, Front and Side Views)
2 • Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB Installation Guide – DOC. 7609A
Page 7
Crestron TSW-RMB Retrofit Mounting Brackets for TSW-750 & TSW-1050
6.10 in
(155 mm)
5.00 in
(127 mm)
3.90 in
(99 mm)
4.50 in
(115 mm)
1.36 in
(35 mm)
TSW-750-RMB-2 Overall Dimensions (Top, Front and Side Views)
Installation Guide – DOC. 7609A Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB • 3
Page 8
Retrofit Mounting Brackets for TSW-750 & TSW-1050 Crestron TSW-RMB
1.42 in
(36 mm)
6.95 in
(177 mm)
CT/LC-1000, AP
AD Mounting Hole
(Use 17517 Bracket)
TPS-4L Mounting Hole
(Use 170070 Bracket)
TPS-2000L Mounting Hole
(Use 17517 Bracket)
3.74 in
(95 mm)
5.00 in
(127 mm)
5.65 in
(144 mm)
4.95 in
(126 mm)
3.95 in
(101 mm)
3.90 in
(99 mm)
TSW-1050-RMB-3 Overall Dimensions (Top, Front and Side Views)
4 • Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB Installation Guide – DOC. 7609A
Page 9
Crestron TSW-RMB Retrofit Mounting Brackets for TSW-750 & TSW-1050
1.35 in
(35 mm)
For 170071 Bracket
Mount to Back Box
4.60 in
(117 mm)
5.10 in
(130 mm)
5.80 in
(148 mm)
8.00 in
(204 mm)
6.50 in
(166 mm)
4.50 in
(115 mm)
TSW-1050-RMB-4 Overall Dimensions (Top, Front and Side Views)
Installation Guide – DOC. 7609A Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB • 5
Page 10
Retrofit Mounting Brackets for TSW-750 & TSW-1050 Crestron TSW-RMB
1.35 in
(35 mm)
6.28 in
(160 mm)
5.59 in
(142 mm)
9.05 in
(230 mm)
7.37 in
(188 mm)
TSW-1050-RMB-5 Overall Dimensions (Top, Front and Side Views)
6 • Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB Installation Guide – DOC. 7609A
Page 11
Crestron TSW-RMB Retrofit Mounting Brackets for TSW-750 & TSW-1050
Setup
Supplied Hardware
The hardware supplied with the TSW-RMB is listed in the following table.
Supplied Hardware for the TSW-RMB
DESCRIPTION PART NUMBER QUANTITY
Mounting Bracket, LC/CT-10001 4001193 2
Mounting Bracket, TPS-4L2 4519515 2
Mounting Bracket, TPS-6L3 4519516 2
Screw, 04-40 x 3/4”, Flat, Phil4 2029110 4
Screw, 04-40 x 1 1/2”, Flat, Phil4 2037906 4
Screw, 06-32 x 1 1/2”, Flat Phil5 2031703 4
1. This item is included with the TSW-750-RMB-1 and TSW-1050-RMB-3.
2. This item is included with the TSW-750-RMB-2.
3. This item is included with the TSW-1050-RMB-4.
4. This item is included with the TSW-750-RMB-1, TSW-750-RMB-2, TSW-1050-RMB-3 and
TSW-1050-RMB-4.
5. This item is included with the TSW-1050-RMB-5.
Installation Guide – DOC. 7609A Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB • 7
Page 12
Retrofit Mounting Brackets for TSW-750 & TSW-1050 Crestron TSW-RMB
Installation
Installation with a Back Box
For applications where there is an existing back box, use the four included #04-40 x
1 1/2” screws (2037906) to install the TSW-RMB.
The following illustration shows a TSW-750 touch screen installation using a
TSW-750-RMB-1 with a BB-1000L back box but installation with a back box is
similar for all TSW-RMB models.
TSW-RMB Installation with Back Box
8 • Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB Installation Guide – DOC. 7609A
Page 13
Crestron TSW-RMB Retrofit Mounting Brackets for TSW-750 & TSW-1050
Installation without a Back Box
For applications where there is no existing back box, use the following installation
procedure:
1. Use the four included #04-40 x 3/4” screws (2029110) to loosely attach the
TSW-RMB to the included mounting brackets. Install the screws only
enough to engage the threads in the mounting brackets. Do not tighten them
yet.
2. Push the assembly into the wall until the brackets are fully seated and “clip”
to the wall.
3. Tighten the four screws to secure the TSW-RMB.
The following illustration shows a TSW-750 touch screen installation using a
TSW-750-RMB-1 with its included mounting brackets but installation without a
back box is similar for all TSW-RMB models.
TSW-RMB Installation without Back Box
Installation Guide – DOC. 7609A Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB • 9
Page 14
Retrofit Mounting Brackets for TSW-750 & TSW-1050 Crestron TSW-RMB
Resources
Further Inquiries
To locate specific information or resolve questions after reviewing this guide,
contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876] or, for
assistance within a particular geographic region, refer to the listing of Crestron
worldwide offices at
To post a question about Crestron products, log onto Crestron’s Online Help at
www.crestron.com/onlinehelp. First-time users must establish a user account to fully
benefit from all available features.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of
the TSW-RMB, additional information may be made available as manual updates.
These updates are solely electronic and serve as intermediary supplements prior to
the release of a complete technical documentation revision.
www.crestron.com/offices.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
10 • Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB Installation Guide – DOC. 7609A
Page 15
Crestron TSW-RMB Retrofit Mounting Brackets for TSW-750 & TSW-1050
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange or service without prior authorization from
Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer.
Only authorized Crestron dealers may contact the factory and request an RMA (Return
Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name
and phone number of contact person, RMA number and return address.
2. Products may be returned for credit, exchange or service with a Crestron Return Merchandise
Authorization (RMA) number. Authorized returns must be shipped freight prepaid to Crestron,
6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with RMA number clearly marked
on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall
be subject to refusal. Crestron reserves the right in its sole and absolute discretion to charge a 15%
restocking fee plus shipping costs on any products returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by Crestron,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
Crestron Limited Warranty
Crestron Electronics, Inc. warrants its products to be free from manufacturing defects in materials and
workmanship under normal use for a period of three (3) years from the date of purchase from Crestron,
with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads
and power supplies are covered for a period of one (1) year; touch screen display and overlay components
are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from Crestron or an authorized Crestron dealer.
Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any.
Crestron shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall Crestron
be liable for incidental or consequential damages of any kind (property or economic damages inclusive)
arising from the sale or use of this equipment. Crestron is not liable for any claim made by a third party or
made by the purchaser for a third party.
Crestron shall, at its option, repair or replace any product found defective, without charge for parts or labor.
Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, Crestron makes no other warranties, expressed or implied,
nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or
fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms
of this limited warranty. This warranty statement supersedes all previous warranties.
Installation Guide – DOC. 7609A Retrofit Mounting Brackets for TSW-750 & TSW-1050: TSW-RMB • 11
Page 16
Crestron Electronics, Inc. Installation Guide – DOC. 7609A
15 Volvo Drive Rockleigh, NJ 07647 (2038191)
Tel: 888.CRESTRON 11.13
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Loading...