Page 1
DO GUIDE
TSW-752
7" Touch Screen
DO Install the Touch Screen
The Crestron® TSW-752 touch screen installs easily over a standard 2-gang or 3-gang U.S.
electrical box or over a 2-gang European electrical box. It can also be attached directly to
drywall and other surfaces over the front of a 2 3/8” (60 mm) high by 3 3/8” (86 mm) wide cutout.
When installed, the touch screen protrudes just 1/2” (13 mm) from the mounting surface and is
magnetically adhered to its mounting bracket, eliminating any visible screws for an ultra clean
appearance.
NOTE: For proper positioning of the touch screen, the electrical box or cutout must be
positioned approximately 1/4” (6 mm) to the right of the touch screen’s center and 1/10” (3 mm)
above its center.
To mount the TSW-752 into an electrical box, use the following procedure:
1. Use four of the eight included screws (four 06-32 x 3/4” or four 3 x 16 mm screws) to attach
the mounting bracket to the electrical box, as shown in the following illustrations.
NOTE: For U.S.-style installations, use a #2 Phillips screwdriver. For European-style
installations, use a #1 Phillips screwdriver or equivalent.
For U.S.-style installations, use the 06-32 x 3/4” screws.
DO Check the Box
QTY PRODUCT COLOR PART NUM.
1 Cable Mount Ferrite Bead 2033216
1 Mounting Bracket 4516761
4 Screws, 06-32 x 3/4", Undercut Head, Phillips 2033247
4 Screws, 3 x 16 mm, Flat Head, Phillips 2013788
For European-style installations, use the 3 x 16 mm screws.
2. Make connections to the TSW-752 using Crestron power supplies for Crestron equipment.
Apply power after all connections have been made.
NOTE: The included cable mount ferrite bead, FBTH-2, should be placed on the LAN
cable in the electrical box.
3. Carefully hold the touch screen over the mounting bracket and gently place it in position.
The magnets on the rear of the touch screen hold it in place on the mounting bracket.
DO Connect the Device
Connect the TSW-752 to the LAN as shown in the following illustration.
Page 2
DO Access the Setup Screen
NOTE: The TSW-752 can take up to 120 seconds to boot.
When power is applied for the rst time, the screen shown in the following illustration appears.
Tap the Setup button to display the TSW-752 Setup screen. The buttons on the Setup screen
enable basic conguration prior to regular operation of the TSW-752.
NOTE: During regular operation of the touch screen, there are two ways to activate the setup
functions:
1. Place a button on the project’s main page and assign the reserved join number (17242) that
activates setup.
2. Touch the hard keys labeled below as 1, 2, 3, and 4 in sequence twice (touch 1, 2, 3, 4, 1, 2,
3, 4) within a ve second period.
1
2
3
4
NOTE: For details on conguring the TSW-752, refer to Doc. 7578 at
www.crestron.com/manuals.
As of the date of manufactur e, the pro duct ha s been te sted an d found to c omply with specications for CE mark ing.
Federal Communications Commission (FCC) Compliance Statement
This device complies with par t 15 of the FCC Rules. Operation is subject to the followin g condi tions:
(1) This devic e may not ca use har mful interfe rence and (2) this device must acc ept any interfe rence received, including interference
that may cause undesired operation.
Caution: Chang es or modicat ions not expres sly app roved by the manufacture r responsibl e for compliance could void the us er’s
author ity to op erate the equip ment.
Note: This equipment has been tested and found to c omply w ith the limits for a C lass B di gital device, pursua nt to par t 15 of the
FCC Rules. Thes e limits a re desi gned to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, u ses and can radiate radi o frequ ency en ergy an d, if not in stalled and us ed in accordance with the
instruction s, may cause harmful interference to r adio communication s. However, the re is no gu arantee that interfe rence will not
occur in a particular i nstal lation.
DO GUIDE
DO Learn More
Visit the website for additional information and the latest rmware updates.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
If this equipment does cause harmful interferenc e to radio o r television reception, which c an be determined by turning the
equipment off and on, th e user is encouraged to t ry to correct t he inter fere nce by one o r more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separ ation between the equipment a nd receiver
• Connect the e quipment into an outlet on a circuit different f rom that to which th e recei ver is connecte d
• Consult the dealer or an experienced radio/T V techn ician for help
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Crestr on produc t developmen t soft ware is licen sed to Cres tron deal ers and Cre stron S ervice P roviders ( CSPs) un der a limited no n-exclusi ve, non-tr ansfera ble Soft ware Deve lopment Tools
License A greement. Cre stron produc t operating sys tem softwa re is licensed to C restron deale rs, CSPs, a nd end-users un der a separate En d-User Lice nse Agreement . Both of these A greements
can be found o n the Crestron web site at www.crestron.com/legal/sof tware_license_agreement.
The speci c patents that c over Crestron pro ducts are listed a t patents.crestron.com. Product w arranty can be f ound at www.crestron.com/warranty.
Crestr on and the Crest ron logo are eit her trademark s or registered t rademarks of C restron Elec tronics, Inc . in the United St ates and/or ot her countrie s. Other trade marks, regist ered trademar ks,
and trade na mes may be used in this d ocument to refer t o either the enti ties claiming the ma rks and names or the ir products. C restron discl aims any propriet ary interes t in the marks and nam es
of others . Crestron is not r esponsible for err ors in typogra phy or photography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2015 Crestron Electronics, Inc.
DOC. 76 60A (2 043 931) 05 .15
Specic ations subject to c hange without not ice.
Loading...