Page 1
DO GUIDE
TSW-732
7” Room Scheduling Touch Screen
DO Change the Button Inserts or Button Covers
The Crestron® TSW-732 Touch Screen ships with 10 “hard key” push buttons for quick access to
commonly used functions. Optional, custom engravable button covers are available (TSW-730-BTNO
and custom engraving sold separately). For a clean appearance, either column of buttons may be
removed and covered using the included no-button covers.
To change the inserts or covers, use the following procedure:
1. Insert a small at head screwdriver into the appropriate hole on the bottom of the TSW-732 to
release its cover.
Insert a screwdriver to release the covers.
2. Gently remove the cover from the TSW-732.
3. If removing the button insert after removing the button cover, use a small at head screwdriver
to press the tabs, and then gently lift the button insert from the TSW-732. Refer to the following
illustration for the tab locations on the button insert.
Touch Screen with Button Inserts
DO Check the Box
QUANTITY PRODUCT COLOR PART NUMBER
1 Bit, Torx, T8 2025915
1 Cover, Plastic, No Buttons, Left Side, 4.5"x 1" x 0.625"
1 Cover, Plastic, No Buttons, Left Side, 4.5" x 1" x 0.625"
DO Install the Touch Screen
The TSW-732 can be mounted into a standard
electrical box or onto a at surface. A tabletop
enclosure and swivel mount (TSW-730-TTK and
SMK-4SM/730, both sold separately) are also
available.
Mounting into a U.S. Electrical Box
To mount the TSW-732 into a U.S. electrical box,
use the following procedure:
1. Insert a small at head screwdriver into the
hole shown in the following illustration, and
gently separate the back panel from the touch screen.
Insert a screwdriver to separate the back panel.
2. Use the four included 6-32 x 1-1/2" screws to attach the back panel to the electrical box.
U.S. Electrical Box
1 Cover, Plastic, No Buttons, Right Side, 4.5" x 1" x 0.625"
1 Cover, Plastic, No Buttons, Right Side, 4.5" x 1" x 0.625"
2 Screw, 4B x 3/4", Flat Head, Phillips 2019 088
2 Screw, 4-40 x 1/4", Undercut Head, Phillips
2 Screw, 4-40 x 1/4", Undercut Head, Phillips
2 Screw, 4-40 x 1/4", Flat Head, Torx
2 Screw, 4-40 x 1/4", Flat Head, Torx
4 Screw, 6-32 x 1-1/2", Flat Head, Phillips 2031703
1. This part s hips with t he TSW-73 2-B-S.
2. This part ships wi th the TS W-732-W-S .
1
2
1
2
1
2
1
2
Black 2033452
White 2033451
Black 2033450
White 2033449
Black 2007152
2007160
Black 2025311
2025312
PIN DESCRIPTION
G Ground
2 Occupancy sensor #2 status
1 Occupancy sensor #1 status
24 24 Vdc power
4. Carefully position the front of the touch screen over the back panel and gently snap it into place.
5. Use two of the included 4-40 x 1/4" screws to secure the TSW-732. For standard applications,
use the Phillips screws. For secure applications, use the security type Torx screws along with
the included Torx screwdriver bit.
Use a screwdriver
to release
the button insert.
4. Carefully position the new cover over the front of the touch screen and press it into place.
Touch Screen with No-Button Covers
Screws (4) 6-32 x 1-1/2"
TSW-732
3. Make connections to the TSW-732 using Crestron power supplies for Crestron equipment.
Occupancy Sensor Input:
From Room Occupancy Sensor
LAN PoE:
10BASE-T / 100BASE-TX
Ethernet to LAN
Screws (2) 4-40 x 1/4" Phillips
or
Screws (2) 4-40 x 1/4" Torx
Mounting into a U.K. Electrical Box
To mount the TSW-732 into a U.K. electrical box, use the following procedure:
1. Insert a small at head screwdriver into the hole shown in the following illustration, and gently
separate the back panel from the touch screen.
Insert a screwdriver to separate the back panel.
Page 2
2. Use the two included 4B x 3/4" screws to attach the back panel to the electrical box.
U.K. Electrical Box
Screws (2) 4B, 3/4"
4. Carefully position the front of the touch screen over the back panel and gently snap it into place.
5. Use two of the included 4-40 x 1/4" screws to secure the TSW-732. For standard applications,
use the Phillips screws. For secure applications, use the security type Torx screws along with the
included Torx screwdriver bit.
Screws (2) 4-40 x 1/4" Phillips
or
Screws (2) 4-40 x 1/4" Torx
The main setup screen is displayed.
TSW-732
3. Make connections to the TSW-732 using Crestron power supplies for Crestron equipment.
Occupancy Sensor Input:
From Room Occupancy Sensor
LAN PoE:
10BASE-T / 100BASE-TX
Ethernet to LAN
PIN DESCRIPTION
G Ground
2 Occupancy sensor #2 status
1 Occupancy sensor #1 status
24 24 Vdc power
DO Access the Setup Screens
NOTE: The TSW-732 can take up to 120 seconds to boot.
The setup screens enable basic conguration prior to regular operation of the TSW-732. To display
the main setup screen, touch the screen while applying power to the unit.
NOTE: If no project has been loaded or if an invalid project has been loaded, the touch screen
defaults to the main setup screen.
During regular operation of the touch screen, there are two ways to activate the setup functions:
1. Place a button on the project main page, and assign the reserved join number (17242) that
activates setup.
2. Press hard keys 1, 2, 3, and 4 on the left side of the touch screen display in sequence, twice
(press 1, 2, 3, 4, 1, 2, 3, 4) within a 5-second period.
1
2
3
4
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn more
about this product, use a QR reader application on your mobile device to scan the QR
image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manuf acture, the produ ct has be en teste d and found to comply with specications for CE m arking.
Federal Communications Commission (FCC) Compliance Statement
This device comp lies with part 15 of the FCC Rules. Operation is sub ject to the followin g two conditions:
(1) This devic e may not cause harm ful interference, and (2) this device must accept any interfe rence re ceived, including inter feren ce that may cause un desire d opera tion.
CAUTION: Changes or modications not expres sly approved by the manufacturer re sponsible for co mplian ce could void the user’s authority to operate the e quipment.
NOTE: This equipment has be en teste d and foun d to comply with the limits for a Cl ass B digi tal devi ce, pursuant to pa rt 15 of the FCC Rules. Th ese limits are designed to p rovide re asonable prote ction
agains t harmful inter ference in a residential installation. T his equipment generates, uses a nd can radiate radio frequ ency ene rgy and, if not inst alled and used in a ccordance with the instr uctions, may
cause harmful interfe rence to r adio com munica tions. H owever, there is no guara ntee that interference will not occur in a par ticular installation.
If this equipment does cause harm ful inter ference to radi o or television rec eption, which ca n be deter mined by tu rning the equipm ent off a nd on, the user is enc ouraged to try to c orrec t the inter ference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation betwe en the equipment and rece iver.
• Connect the equipment into an outlet on a circuit different from that to which the re ceiver i s connected.
• Consult the dealer or an experien ced radio/T V technician for help.
DO GUIDE
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Crestr on product develop ment softwar e is licensed to Cres tron dealers and C restron Ser vice Providers ( CSPs) under a limit ed non-exclusive, no n-transfera ble Softwar e Development Tools Lic ense Agreement. C restron produ ct operating sys tem software i s licensed to Cres tron dealers, C SPs, and
end-user s under a separate E nd-User Licens e Agreement. Bot h of these Agreemen ts can be found on the C restron websit e at www.crestr on.com/legal /software _license_agr eement.
The speci c patents that c over Crestron pro ducts are listed a t patents.crestron.com The product warranty can be found at www.crestron.com/warranty.
Certa in Crestron pro ducts contain op en source soft ware. For speci c information, ple ase visit www.crestron.com/opensource.
Crestr on and the Crestr on logo are either tr ademarks or regis tered trademark s of Crestron Ele ctronics, Inc., i n the United Stat es and/or other cou ntries. Other t rademarks, regi stered trademar ks, and trade names m ay be used in this docume nt to refer to either t he entities claimin g the marks and
names or the ir products. Cre stron disclaims an y proprietary i nterest in the mark s and names of other s. Crestron is not r esponsible for err ors in typogra phy or photography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2015 Crestron Electronics, Inc.
DOC. 76 68B (2 040 919) 09 .15
Specic ations subject to c hange without not ice.
Loading...