Page 1
DO GUIDE
TSW-560/760/1060-TTK and TSW-560/760/1060-SMK
TableTop Kits and Swivel Mount Kit for TSW-560/760/1060
The Crestron® TSW-560-TTK, TSW-760-TTK, and TSW-1060-TTK are functionally identical. For simplicity within this guide, the term
“TSW-560/760/1060-TTK” is used except where noted.
DO Prepare the TSW-560/760/1060-TTK
The TSW-560/760/1060-TTK includes parts for routing device cabling through either the bottom or rear of the unit.
Routing the Cable though the Bottom of the TSW-560/760/1060-TTK
The TSW-560/760/1060-TTK has a circular opening in its metal base that allows an Ethernet cable to pass through the bottom, enabling network connection
when the unit is attached to the TSW-560/760/1060-SMK Swivel Mount Kit (sold separately).
Routing the Cable though the Rear of the TSW-560/760/1060-TTK
Modication is necessary to install the TSW-560/760/1060-TTK on a at surface. Replace the rear plastic cap with the provided grommet to route the
Ethernet cable through the rear of the unit. The grommet serves as a strain relief on the cable.
1. Remove the two screws on the bottom of the unit that hold the metal bracket. Retain the metal bracket and screws.
Metal bracket
Remove these screws
to release the metal bracket.
Bottom of TSW-560/760/1060-TTK
2. Remove the rear plastic cap by pressing the top of the cap inward until it unsnaps.
3. Insert the Ethernet cable through the rear opening of the TSW-560/760/1060-TTK and attach the provided grommet to the cable.
Plastic cap
DO Check the Box
QUANTITY ITEM PART NUMBER
Items for TSW-560/760/1060-TTK Only
2 Screw, M3 x 0.5 x 6 mm, Pan Head, Phillips 2047840
1 Template, Cutout 45 25014
Items for TSW-560/760/1060-TTK-B-S Only
1 Grommet, Rubber, Black 2047839
Items for TSW-560/760/1060-TTK-W-S Only
1 Grommet, Rubber, White 20478 38
Items for TSW-560/760/1060-SMK Only
1 Nu t , 7/8"-14 20176 32
1 Plate, Swivel Stop 4504353
3 Screw, 6-32 x 3/16", Pan Head, Phillips 2007202
2 Screw, 8-32 x 1/8", Cap Head, Socket 20176 34
6 Screw, 8-8B x 1/2", Pan Head, Phillips 2017784
1 Template, Cutout 45 25014
1 Washer, 1.75" OD, 15/16" ID, 0.14" TH 20176 33
1 Washer, Cork/Rubber, 1.75" OD, 0.94" ID, 1/16" TH 20176 14
1 Washer, Felt, 2.65" OD, 0.93" ID 20 24711
1 Washe r, Ke yed 4506321
1 Washer, Rubber, 1.75" OD, 0.94" ID, 1/16" TH 20176 15
DO Assemble the TSW-560/760/1060-SMK
Assemble the Swivel Mount
To assemble the swivel mount:
1. Attach and secure the swivel mechanism tube to the bottom of the TSW-560/760/1060-TTK using the three included 6-32 x 3/16" screws.
4. Secure the grommet to the back of the TSW-560/760/1060-TTK by pressing it into place.
NOTE: For added security, refer to “DO Use the Security Option” and follow the procedure. For standard mounting, proceed to the next step.
5. Reinstall the metal bracket using the screws removed in step 1.
DO Mount the Touch Screen in the TSW-560/760/1060-TTK
To mount the touch screen:
1. Connect the Ethernet cable to the touch screen.
2. Gently pull excess cable out through the rear of the TSW-560/760/1060-TTK as the touch screen and tabletop kit converge.
3. Seat the touch screen in the TSW-560/760/1060-TTK fully to engage the spring-loaded retainers built into the metal bracket.
TSW-560/760/1060-TTK
Swivel mechanism tube
Screws (3) 6-32 x 3/16"
Felt washer
2. Remove the paper liner from the felt washer and attach the washer to the bottom of the swivel mechanism tube.
3. If the Ethernet cable is routed to exit through the bottom of the TSW-560/760/1060-TTK, feed the full length of the cable through the swivel
mechanism tube.
4. Use the included template to prepare the mounting surface.
5. Using the six mounting holes on the swivel stop plate as a template, drill pilot holes in the mounting surface. The holes should be 0.093" (2 mm)
minimum diameter, 0.115" (3 mm) maximum diameter, and 0.35" (9 mm) maximum depth.
6. Attach the swivel stop plate to the bottom of the mounting surface using the six included 8-8B x 1/2" screws.
7. Pass the swivel mechanism tube attached to the TSW-560/760/1060-TTK down through the mounting hole and swivel stop plate.
NOTE: The swivel stop plate has a permanently installed limiting screw to prevent the swivel mechanism from spinning and tangling the touch
screen cable.
Page 2
8. Attach or slide the included hardware up onto the swivel mechanism tube in the order indicated in the illustration that follows step 9.
NOTE: Orient the keyed metal washer tab to face away from the permanently installed limiting screw.
9. Adjust the tightness of the 7/8"-14 nut to achieve the desired swivel assembly motion resistance. Use a flat tool, such as a large flat-head
screwdriver, in the slot on the bottom of the swivel mechanism tube to hold the tube steady while tightening the nut.
Table or mounting surface (front edge)
Bottom side of table or mounting surface
Mounting hole
Swivel mechanism tube
Slot in tube
Mounting holes (6)
in swivel stop plate
Screws (2) 8-32 x 1/8"
Permanently installed limiting screw
Swivel stop plate
DO Use the Security Option
Use the two included M3 x 0.5 x 6 mm screws to lock the touch screen to the TSW-560/760/1060-TTK.
1. Remove the two screws on the bottom of the unit that hold the metal bracket. Retain the metal bracket and screws.
Metal bracket
Remove these
screws to release
the metal bracket.
Bottom of TSW-560/760/1060-TTK
2. Place the touch screen face down on a clean, soft cloth (not provided) and remove the two 1/2" long screws from the rear assembly. Retain these
screws to restore the touch panel without the security option, if necessary.
Cork and rubber washer
Screws (6) 8-8B x 1/2"
Keyed metal washer
Rubber washer
Steel washer
Nut 7/8"-14
Customize the Swivel Range
Reposition the two 8-32 x 1/8” screws placed on the swivel stop plate to customize the swivel range (330-degree rotation, maximum). Refer to the following
illustrations for details.
Keyed metal
washer tab
where swivel
motion starts
Six locations
for additional
limiting screws
Permanent
limiting screw
30º
90º
135º
Insert the two
limiting screws
to set the desired
swivel range.
Permanent
limiting screw
Remove
these
screws.
3. Secure the metal bracket to the rear assembly.
Screws (2)
M3 x 0.5 x 6 mm
Metal
bracket
a. Position the bracket correctly (right side up, as shown above).
b. Secure the bracket with two included M3 x 0.5 x 6 mm screws. To prevent damage to threads, turn each screw counterclockwise until it
engages the thread.
c. Tighten the screws to 3 in/lb.
4. Secure the touch screen to the TSW-560/760/1060-TTK.
a. Connect the Ethernet cable to the touch screen while it remains face down.
b. Position the TSW-560/760/1060-TTK over the touch screen and gently pull any excess cable out through the rear of the tabletop accessory
until the two units come together.
c. Secure the TSW-560/760/1060-TTK to the touch screen with the two screws removed in step 1.
DO GUIDE
DO Learn More
Visit the website for additional information and the latest rmware updates.
To learn more about this product, use a QR reader application on your
mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
The speci c patents that c over Crestron pro ducts are listed a t www.crestron.com/legal/patents.
The produ ct warranty ca n be found at www.crestron.com/legal/sales-terms-conditions-warranties.
Certa in Crestron pro ducts contain op en source soft ware. For speci c information, vi sit www.crestron.com/legal/open-source-software.
Crestr on and the Crestro n logo are either tra demarks or registe red trademarks of C restron Electr onics, Inc., in the Un ited States and /or other countrie s. Other tradema rks, registered t rademarks,
and trade na mes may be used in this do cument to refer to ei ther the entitie s claiming the marks a nd names or their prod ucts. Crestr on disclaims any pro prietary inte rest in the marks an d names of
others. C restron is not re sponsible for erro rs in typograph y or photography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2018 Crestron Electronics, Inc.
TSW-560-TTK TS W-7 6 0-T TK T S W -10 6 0 - T T K
DOC. 79 28B ( 20472 66) 05.18
Specic ations subject to c hange without not ice.
TSW-560/760/1060-SMK
Loading...