Page 1
DO GUIDE
TSW-560/TSW-760/TSW-1060
5", 7", and 10.1" Touch Screens
DO Install the TSW-560 Mounting Bracket
The Crestron® TSW-560 touch screen can be mounted into drywall and other surfaces, or it can be mounted onto a wall stud. When mounted into drywall
and other surfaces, the touch screen protrudes 1/2" (13 mm) from the mounting surface.
To mount the TSW-560, use the following procedure:
1. For preconstruction applications, use standard drywall nails or screws (not included) to attach the included preconstruction mounting bracket to a
wall stud.
Preconstruction bracket
Use a tie wrap to hold the cable
until the TSW-560 is mounted.
CAUTION: Allow an air gap of at least 12" (305 mm) in the wall cavity above and below the TSW-560 for heat dissipation.
For postconstruction applications, use the preconstruction bracket as a cutout template by turning the bracket to face the wall, ensuring it is level,
and temporarily tacking it to the wall with nishing nails (not included) in the smaller holes around the cutout opening. Trace the cutout opening with
an appropriate drywall saw (not included).
DO Check the Box
QUANTITY PRODUCT PART NUMBER
Items for TSW-560 Only
1 Latch, Security 4525305
1 Bracket, Universal Mounting 4525127
1 Bracket, Preconstruction 4524592
Items for TSW-760 and TSW-1060 Only
1 Bracket, Mounting 4525352
1 Latch, Security 4525305
4 Screw, 6-32 x 3/4", Undercut Head, Phillips 2033247
2 Screw, M3.5 x 25 mm, Flat Head, Phillips 2023756
4 Screw, M3 x 16 mm, Flat Head, Phillips 2013788
DO Install the TSW-760 or TSW-1060 Mounting Bracket
The TSW-760 and TSW-1060 touch screens install over a standard 2-gang or 3-gang U.S. electrical box, a 2-gang European electrical box, or a 2-gang
U.K. electrical box. The touch screens can also be attached directly to drywall and other surfaces over the front of a 2-3/8" (60 mm) high by 3-3/8" (86
mm) wide cutout. When installed, the touch screen protrudes 1/2" (13 mm) from the mounting surface, eliminating any visible screws.
To mount the TSW-760 or TSW-1060 into an electrical box, use the appropriate included screws (four 6-32 x 3/4" screws, four M3 x 16 mm screws, or
two M3.5 x 25 mm screws) to attach the mounting bracket to the electrical box, as shown in the following illustrations.
NOTE: For U.S.-style installations, use a #2 Phillips screwdriver. For European or U.K.-style installations, use a #1 Phillips screwdriver or equivalent.
For U.S.-style installations, use the four 6-32 x 3/4" screws.
U.S. electrical box
Universal mounting bracket
2. Loosen the two screws on the included universal mounting bracket, and then install the universal mounting bracket, bottom rst, into the opening.
Loosen both of the screws.
Push the top surface
downward to install
the bottom half rst.
Universal mounting bracket
3. Reach into the universal mounting bracket and push the rear half back to ensure it is fully behind the mounting surface. Ensure the front of the
universal mounting bracket is level, and then tighten the two screws to complete the installation.
CAUTION: To avoid damage to the bracket, do not overtighten the screws.
Mounting bracket
Screws (4): 6-32 x 3/4"
TSW-760 or TSW-1060
For European-style installations, use the four M3 x 16 mm screws.
European electrical box
Mounting bracket
Screws (4): M3 x 16 mm
Push the rear half back.
Ensure the front is level.
Then, tighten both screws.
TSW-760 or TSW-1060
For U.K.-style installations (not pictured), use the two M3.5 x 25 mm screws.
To complete the installation, refer to “DO Complete the Installation” on the next page.
Page 2
DO Install the Touch Screen Security Latch (Optional)
The touch screen comes with a security latch, which can be installed so that the touch screen cannot
be easily removed from the mounting bracket after installation.
To install the security latch, use a small Phillips screwdriver to screw the security latch to the top of
the touch screen’s rear housing before the touch screen has been inserted into the mounting bracket.
Security latch
DO Complete the Installation
Make connections to the touch screen using Crestron power supplies for Crestron equipment. Power
and data connection to the touch screen is provided by a single Ethernet cable connected to the
LAN port on the rear of the unit. A Crestron PoE (Power over Ethernet) power supply or PoE-capable
network switch is recommended (both sold separately). Apply power after the Ethernet cable is
connected.
Tap Enter Setup to display the main Setup screen.
Touch screen
To remove the touch screen after the installation is complete, pull the touch screen away from the wall
until the security latch makes contact with the mounting bracket. Then, insert a at-head screwdriver
Mounting bracket
Touch screen
Security latch
Insert the screwdriver here.
into the slot on the security latch and rotate the latch into the open position, which causes the security
latch arms to retract. While the arms are retracted, pull on the touch screen to disengage it from the
mounting bracket.
NOTE: There is a small amount of “play” in the bracket mounting, which allows room for the
screwdriver.
Reset button
LAN PoE:
10BASE-T / 100BASE-TX
Ethernet to LAN
Once all connections to the device have been made, carefully hold the touch screen over the
mounting bracket and gently place it in position.
NOTE: If the touch screen is not level after installation, pull the touch screen out of the mounting
bracket and slightly loosen the screws holding the bracket into place. This procedure allows the
mounting bracket to be slightly rotated. Once the mounting bracket has been repositioned, retighten
the screws, reinstall the touch screen into the bracket, and ensure that the touch screen is now level.
DO Access the Setup Screens
NOTE: The touch screen can take up to 120 seconds to boot.
When power is applied for the rst time, the following screen appears.
NOTE: During regular operation of the touch screen, there are two ways to activate the setup
functions:
• Place a button on the project main page, and assign the reserved join number (17242) that
activates setup.
• Tap the hard keys labeled below as 1, 2, 3, and 4 in sequence twice (tap 1, 2, 3, 4, 1, 2, 3, 4)
within a 5-second period.
1
2
3
4
DO Congure the Touch Screen
Use the setup screens to congure various settings for the touch screen, including Ethernet setup, IP
table setup, audio setup, display setup, standby timeout, and diagnostics. For more information on
conguring the touch screen, refer to the TSW-560, TSW-760, and TSW-1060 Supplemental Guide
(Doc. 7927) at www.crestron.com/manuals.
As of the date of manufactur e, the pro duct ha s been te sted an d found to c omply with specications for CE mark ing.
Federal Communications Commission (FCC) Compliance St atement
This device complies with par t 15 of the FCC Rules. Operation is subject to the followin g two con ditions:
(1) This devic e may not ca use har mful interfe rence, and (2) thi s device must accept any interferenc e recei ved, including i nterference that may cause undesired operation.
CAUTION: Changes or modic ations not expressly a pprove d by the manufacturer responsible for c ompliance could void th e user’s au thority to ope rate the e quipment.
NOTE: This equipm ent has b een tested and found to comply with the limi ts for a Class B digital device, pursuant to part 15 of the FCC Rule s. These limit s are des igned to provide r easonable protection
agains t harmful interference in a re sidential installation. This equipment g enerates, us es and can radia te radio f reque ncy ene rgy and, if not ins talle d and used in accordance with the instructions, may
cause harmful inter ference to radio communicati ons. However, there is n o guara ntee that inter ference will not occur in a particula r insta llatio n.
If this equipment does cause harmful interferenc e to radio o r television reception, which c an be determined by turning the equipme nt off and on, the u ser is en couraged to tr y to correct the inter ference
by one or more of the following measur es:
• Reorient or relocate the receiving antenna.
• Increase the se paration bet ween the equipment and receiver.
DO GUIDE
DO Learn More
Visit the website for additional information and for the
latest rmware updates. To learn more about these
products, use a QR reader application on your
mobile device to scan the appropriate QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
• Connect the equipment into an ou tlet on a circuit d ifferent fro m that to which the re ceive r is connected.
• Consult the dea ler or an experi enced radio/ TV technician for h elp.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Crestr on product develop ment softwar e is licensed to Cres tron dealers and C restron Ser vice Providers ( CSPs) under a limit ed non-exclusive, no n-transfera ble Softwar e Development Tools Lic ense Agreement. C restron produ ct operating sys tem software i s licensed to Cres tron dealers, C SPs, and
end-user s under a separate E nd-User Licens e Agreement. Bot h of these Agreemen ts can be found on the C restron websit e at www.crestron.com/legal/soft ware_license_agreement. The speci c patents that co ver Crestron pro ducts are listed a t http://www.crestron.com/legal/patents. The
product w arranty can be fo und at www.crestron.com/warranty.
Certa in Crestron pro ducts contain op en source soft ware. For speci c information, ple ase visit www.crestron.com/opensource.
Crestr on and the Crestr on logo are either tr ademarks or regis tered trademark s of Crestron Ele ctronics, Inc., i n the United Stat es and/or other cou ntries. Other t rademarks, regi stered trademar ks, and trade names m ay be used in this docume nt to refer to either t he entities claimin g the marks and
names or the ir products. Cre stron disclaims an y proprietary i nterest in the mark s and names of other s. Crestron is not r esponsible for err ors in typogra phy or photography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2016 Crestron Electronics, Inc.
TSW-560
TS W-7 60
DOC. 7926B (2047264) 10.16
Specic ations subject to c hange without not ice.
T S W -10 6 0
Loading...