Page 1
TSS-752
Install the Touch Screen
1
7” Room Scheduling Touch Screen
The Crestron® TSS-752 touch screen installs into a standard 2-gang
(or horizontally mounted 1-gang) U.S electrical box, a 2-gang
European electrical box, a 2-gang UK electrical box. It can also
install over a small cutout (for Ethernet access) on virtually any
mounting surface.
To mount the TSS-752 into an electrical box, use the following
procedure:
1. Use four of the eight included screws (four #06-32 x 3/4” or four
3 x 16 mm) to attach the mounting plate (4519681 or 4519719)
quickstart guide
to the electrical box, as shown in the following illustration.
For U.S.-style installations, use the #06-32 x 3/4” screws
(2033247).
For European-style installations, use the 3 x 16 mm screws
(2013788).
NOTE: For U.S.-style installations, use a #2 Phillips
screwdriver. For European-style installations, use a #1
Phillips screwdriver or equivalent.
Attach the Mounting Plate to a U.S. Electrical Box
U.S. Electrical Box
Mounting Plate
(4519719)
2. Gently snap the two mounting plate covers (2037956 or
2037961) into place to hide the screws to the electrical box.
Attach the Mounting Plate Covers
Mounting Plate Covers (2)
(2037956 or 2037961)
3. Carefully position the TSS-752 over the mounting plate to
engage the four screws protruding from the plate. Slide the
TSS-752 to the left until it clicks into place.
Attach the TSS-752 to the Mounting Plate
TSS-752
Mounting Plate
(4519719)
Mounting Plate
(4519719)
NOTE: It some situations where there may not be enough
room to slide the TSS-752 from right to left on the mounting
plate, the plate can be installed with the locking tabs on the
left side. In such cases, attach the TSS-752 by sliding it to
the right until it clicks into place.
4. When making connections to the TSS-752, use Crestron power
supplies for Crestron equipment. Apply power after all
connections have been made.
Hardware Connections for the TSS-752
Reset Button
LAN PoE:
10BASE-T / 100BASE-TX
Ethernet to LAN
1
Screws (4) #06-32 x 3/4”
(2033247)
For regulatory compliance information, refer to Doc. 7601.
QUICKSTART DOC. 7600C (2038155, Sheet 1 of 2) 04.14
www.crestron.com
Specifications subject to
change without notice.
TSS-752
Continued on following page
888.273.7876 201.767.3400
Page 2
TSS-752
7” Room Scheduling Touch Screen
Install the Touch Screen (Continued)
1
In the event it becomes necessary to remove the TSS-752 from the mounting plate, use the following
procedure:
1. Insert the included release key (2039324) between the back of the TSS-752 and the mounting plate, on
the side of the plate with the two locking tabs.
2. Gently pull the release key handle so its tines depress the locking tabs on the mounting plate. At the
same time, slide the TSS-752 to the right about 1/4” (~7 mm) to unlock it from the mounting plate.
Remove the TSS-752 from the Mounting Plate
quickstart guide
Mounting Plate
(4519719)
TSS-752
Release Key
(2039324 )
3
Configure the Touch Screen
NOTE: The only connection required to configure the touch screen is power.
Refer to step 2 in section ➊ “Install the Touch Screen” for details.
NOTE: The TSS-752 can take up to 45 seconds to boot to a display after initial power up.
The setup screens enable basic configuration procedures prior to regular operation of the TSS-752.
To access the setup screens after the TSS-752 boots up to the Fusion RV® Scheduling “Offline” screen,
touch “hard keys” 1, 2, 3 and 4, to the right of the touch screen display, in sequence twice (touch
1, 2, 3, 4, 1, 2, 3, 4) within a five second period.
1
2
3
4
2
2
Establish Communication
Use Crestron Toolbox™ for communicating with the TSS-752; refer to the Crestron Toolbox help
file for details. There is a single method of communication: TCP/IP communication.
Ethernet Communication
Power
Injector
PC Running
Crestron Toolbox
LAN
PoE
3
2
1
Uplink
CRESTRON
CEN-SW-POE-5 Power over Ethernet Switch
Power
120 Volts
4
48VDC
POE
The TSS-752 is preconfigured for DHCP and connects to PC via Ethernet:
1. Use the Device Discovery Tool (click the icon) in Crestron Toolbox to detect all Ethernet
devices on the network and their IP configuration. The tool is available in Toolbox version
1.15.143 or later.
2. Click on the TSS-752 to display information about the device.
For regulatory compliance information, refer to Doc. 7601.
QUICKSTART DOC. 7600C (2038155, Sheet 1 of 2) 04.14
TSS-752
www.crestron.com
Specifications subject to
change without notice.
TSS-752
NOTE: For details on configuring the TSS-752, refer to the TSW-750 Configuration Guide (Doc. 7602).
For details on Fusion RV Scheduling with the TSS-752, refer to the Touch Screens with RoomView®
Scheduling for Crestron Fusion Operations Guide (Doc 7552). They are available at
www.crestron.com/manuals.
888.273.7876 201.767.3400
Page 3
TSS-752
7” Room Scheduling Touch Screen
4
Dimensions
TSS-752 Overall Dimensions (Top View)
6.28 in
(160 mm)
TSS-752 Overall Dimensions (Front and Rear Views)
quickstart guide
7.61 in
(194 mm)
1.20 in
(31 mm)
4.75 in
(121 mm)
1.25 in
(32 mm)
1.41 in
(36 mm)
1.47 in
(38 mm)
3.40 in
(87 mm)
2.80 in
(72 mm)
1.30 in
(33 mm)
5
Pinout Reference
The only connector on the TSS-752 is the LAN PoE port.
LAN PoE
Pin 8Pin 1
PIN DESCRIPTION
1
2
3
4
5
6
7
8
TX +
TX -
RX +
DC +
DC +
RX DC DC -
TSS-752 Mounting Plate Overall Dimensions
4.22 in
(107 mm)
3.28 in
(84 mm)
2.46 in
(63 mm)
1.76 in
(45 mm)
0.94 in
(24 mm)
6.28 in
(160 mm)
4.79 in
(122 mm)
3.62 in
(92 mm)
0.80 in
(21 mm)
3.28 in
(84 mm)
2.79 in
(71 mm)
1.81 in
(46 mm)
2.36 in
(60 mm)
3.28 in
(84 mm)
6
Recommended Cleaning
Keep the surface of the touch screen free of dirt, dust or other materials that could degrade optical
properties. Long-term contact with abrasive materials can scratch the surface, which may detrimentally
affect image quality.
For best cleaning results, use a clean, damp, non-abrasive cloth with any commercially available
non-ammonia glass cleaner. Bezels may not provide a complete watertight seal. Therefore, apply
cleaning solution to the cloth rather than the surface of the touch screen. Wipe touch screen clean and
avoid getting moisture beneath the bezels.
TSS-752
3
For regulatory compliance information, refer to Doc. 7601.
QUICKSTART DOC. 7600C (2038155, Sheet 2 of 2) 04.14
www.crestron.com
Specifications subject to
change without notice.
888.273.7876 201.767.3400
Page 4
TSS-752
7” Room Sceduling Touch Screen
7
quickstart guide
Specifications
Touch Screen Display
Display Type: TFT Active matrix color LCD
Size: 7 inch (178 mm) diagonal
Aspect Ratio: 15:9 WVGA
Resolution: 800 x 480 pixels
Brightness: 300 nits (cd/m
Contrast: 350:1
Color Depth: 18-bit, 262k colors
Illumination: Edgelit LED
Viewing Angle: ±70° horizontal, ±65° vertical
Touch Screen: Projected capacitive
Buttons
Hard Keys: (5) Projected capacitive push buttons for menu navigation
Reset: (1) Miniature push button on rear panel for hardware reset
Room Status Indicators
(2) Side-mounted tri-color red/green/blue LED beacons for room status indication
Memory
LPDDR2 RAM: 1 GB
Flash: 4 GB
Maximum Project Size: 512 MB
Graphics Engine
Supports Smart Graphics™
Crestron Fusion
Chinese (Simplified), Chinese (Traditional), Dutch (Netherlands), English (US), English (UK), French, German, Italian,
Japanese, Russian, Spanish
Communications
Ethernet: 10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, IEEE 802.3af and
802.3at compliant
2
Video
Streaming Formats: H.264 (MPEG-4 part 10 AVC), MJPEG
2
Audio
Features: Built-in microphone and speakers, Rava™ SIP Intercom
Audio Feedback Formats: MP3
®
Language Support
2
)
1
Connections
LAN PoE: (1) 8-wire RJ-45 with 2 LED indicators
10BASE-T/100BASE-TX Ethernet port, Power over Ethernet Plus compliant
Green and yellow LEDs indicate Ethernet port status
Power Requirements
Power over Ethernet: IEEE 802.3at Type 1 (802.3af compatible) Class 3 (12.95W) PoE powered device
Environmental
Temperature: 32° to 112°F (0° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: 28 Btu/Hr
Enclosure
Construction: Plastic, smooth black or white finish
Mounting: Surface mount over a 2-gang electrical box or plaster ring, horizontally-oriented 1-gang electrical box or
plaster ring, 2-gang European (DIN 49073) electrical box, 2-gang UK (BS 4662) electrical box, or small cutout;
optional multi-surface mounting kit sold separately
Dimensions
Height: 4.75 in (121 mm)
Width: 7.61 in (194 mm)
Depth: 1.47 in (38 mm) with mounting plate
Weight
17 oz (481 g)
NOTES
1. Supports Smart Graphics only. Not compatible with ”traditional” UI projects.
2. Enabled through custom programming. Not used for typical room scheduling applications.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, Crestron Fusion, Crestron Toolbox, Fusion RV, Rava, RoomView, and Smart Graphics are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks and trade names may be used in
this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names
of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.
TSS-752
4
For regulatory compliance information, refer to Doc. 7601.
QUICKSTART DOC. 7600C (2038155, Sheet 2 of 2) 04.14
www.crestron.com
Specifications subject to
change without notice.
888.273.7876 201.767.3400
Loading...