Page 1
TSR-310-BTP
Battery Pack for TSR-310
Installation Guide
Description
The Crestron® TSR-310-BTP is a rechargeable lithium polymer battery pack that is
designed to replace the battery pack in a Crestron TSR-310 handheld touch screen
remote (not included).
NOTE: To view an instructional video showing the procedures documented in this
guide, visit https://vimeo.com/252558509, or use a QR reader application on your
mobile device to scan the “Instructional Video” QR image located in “Additional
Resources” below.
Additional Resources
Visit the product page on the Crestron website
(www.crestron.com) for additional information and
the latest rmware updates. An instructional video
showing installation procedures can also be
viewed. Use a QR reader application on your
mobile device to scan the QR images, or click the
QR images to load the web pages.
Product Page Instructional Video
Supplied Hardware
Refer to the following table for a complete list of parts that are included with the
TSR-310-BTP:
Supplied Hardware for TSR-310-BTP
QUANTITY ITEM PART NUMBER
1 Tool, Battery Removal 2050938
1 Tool, T-Pin 2050937
Battery Removal Tool and T-Pin Tool
Removing the Battery Cover
7. Hold on to the silver ap attached to the battery pack, and insert the at end of the
battery removal tool underneath the battery pack with the other hand.
8. Place the at end of the battery removal tool under the battery, and then carefully
pry the battery pack up while pulling on the ap until the adhesive backing on the
battery pack separates from the inside of the battery compartment.
CAUTION: Do not press the battery removal tool against the circuit board
components when removing the battery pack.
Removing the Battery Pack
Remove the Existing Battery Pack
To remove the existing battery from the TSR-310:
1. Place the TSR-310 on a clean, soft surface with the screen side facing down. Use
care to avoid scratching the front surface of the TSR-310.
2. Align the included t-pin tool with the small hole on the rear of the TSR-310.
3. Slide the battery cover away from the TSR-310 while pressing the t-pin down and
into the hole.
Removing the Battery Cover
9. Pull the battery pack out the compartment using the ap.
Install the New Battery Pack
Use the following procedure to install the new battery pack into the TSR-310:
1. Peel the adhesive backing off of the bottom of the replacement battery pack to
expose the adhesive surface.
Removing the Adhesive Backing
2. Hold on to the silver ap attached to the battery pack with two ngers, and slide the
battery pack at an angle down and into the TSR-310 battery compartment.
NOTE: The silver side of the battery pack (with the adhesive surface) must be
facing downward.
Inserting the Battery into the TSR-310
4. Lift the battery cover up and off the remote, and remove the insulating shroud that
covers the battery.
5. Place the at end of the battery removal tool underneath the wires extending from
the battery connector.
6. Pull up gently on the wires using the battery removal tool until the battery connector
disengages from the TSR-310 battery compartment.
CAUTION: Do not press the battery removal tool against the circuit board
components when disengaging the battery connector.
3. Press down on the battery pack to adhere the battery pack to the inside of the
battery compartment.
Page 2
4. Press the three wires extending from the battery connector into the three slots on
the slotted end of the battery removal tool to attach the connector. Once the battery
connector is attached to the tool, the red wire should be located on the side of the
tool shown in the second image below.
Attaching the Battery Connector to the Battery Removal Tool
Correct Wire Placement on Battery Removal Tool
7. Slide the insulating shroud over the battery pack so the two tabs on the shroud enter
the spaces in between the sides of the battery pack and the battery compartment.
Placing the Insulating Shroud Over the Battery Pack
8. Lower the battery cover onto the remote so that the two tabs inside the battery
cover engage the two slots on either side of the battery compartment.
Reattaching the Battery Cover to the TSR-310
5. Press the battery connector into the connector slot inside the TSR-310 battery
compartment using the guides on the slotted end of the battery removal tool.
NOTE: Once the battery connector is installed, the red wire must be located next
to the bottom of the remote, and the black wire must be located next to the battery
pack. Refer to the following image for the correct wire placement.
Attaching the Battery Connector to the TSR-310
6. Press the at end of the battery removal tool into the battery connector until it is at
and secured inside of the connector slot.
Securing the Battery Connector
9. Slide the battery cover up and into the remote until the cover snaps into place.
Charge the Battery Pack
Once the TSR-310-BTP replacement battery is installed in the TSR-310, place the
TSR-310 into its charging dock. A “charging” notication appears on the TSR-310 touch
screen display to indicate that the battery is charging.
NOTE: If the TSR-310 attempts to power on following a new battery pack installation
but powers off immediately, place the TSR-310 on its charging dock to continue
powering the device.
Store the Battery Pack
NOTE: The TSR-310-BTP should be charged between 30% and 50% when it is put into
storage.
The TSR-310-BTP may be stored in a temperate, dry location (removed from the TSR-310)
for up to six months without signicant irreversible degradation of its performance. The
self-discharge rate is a function of temperature and internal resistance. High-temperature
storage reduces charge retention. Best results occur when the TSR-310-BTP is stored at a
temperature of 32 ˚F to 95 ˚F (0 ˚C to 35 ˚C).
Dispose of the Battery Pack
NOTE: The TSR-310-BTP contains a lithium polymer battery. When the unit no longer
retains a charge, it must be recycled or disposed of properly. Follow local ordinances
and regulations for disposal.
The battery must be recycled. Deliver the battery to an appropriate recycling
facility for disposal.
As of the date of manufacture, the product has been tested and found to comply with specications
for CE marking.
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specic information, please visit
www.crestron.com/legal/open-source-software.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and names of others.
Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
Crestron Electronics, Inc. Installation Guide - DOC. 8227B
15 Volvo Drive, Rockleigh, NJ 07647 (2049524)
Tel: 888.CRESTRON 05.18
Fax: 201.767.7576 Specications subject to
www.crestron.com change without notice.
Loading...