Page 1
DO GUIDE
TSR-302
Handheld Touch Screen Remote
DO Install the Battery
To install the TSR-302-BTP, perform the following procedure:
1. Remove the battery compar tment cover on the rear of the TSR-302
by using two thumbs and gently pressing in the direction of the arrow
shown in the following photograph.
2. Place the touch screen remote on a clean, soft surface, with the screen
side down.
3. Place the TSR-302-BTP in the battery compartment, oriented as in the
following photograph.
3. Select Enter Setup Mode. The main menu is displayed, as shown in
the illustration below.
NOTE: Select Exit Setup Mode to exit the setup menu.
NOTE: From any of the setup menus, touch to go back to the
previous menu.
For details on conguring the TSR-302, refer to the TSR-302 Conguration
Guide (Doc. 7663) at www.crestron.com/manuals.
DO Set Up Basic Wireless
Before a TSR-302 can be used with a Crestron control system, it must
rst be acquired by a CEN(I)-ERFGW-POE Extended Range RF Wireless
Gateway (sold separately).
To acquire a TSR-302, perform the following steps.
DO Check the Box
QUANTITY PRODUCT PART NUMBER
1 TSR-302-DS Table Dock for TSR-302 4520465
1 PW-1909WU Wall Mount Power Pack 20 41488
1 TSR-302-BTP Battery Pack for TSR-302 2039523
3. When the process is complete, the screen displays an “Acquire OK”
message. Press ACQUIRE on the gateway to exit Acquire mode. The
LED turns off.
For information on wireless setup with roaming, refer to “Gateway Roaming
Setup” in the TSR-302 Conguration Guide (Doc. 7663).
DO Set Up WiFi
From the main menu, touch WiFi® Setup and then Add Access Point to
display the Select Access Point menu.
If the desired wireless access point is already on the list, touch Connect.
2. Touch the WAP Name (SSID) eld to open an on-screen keyboard,
which can be used to enter the name.
3. Touch the Security eld to display the Encryption screen.
4. Select the appropriate type of encryption, and then touch to
return to the Conrm Info menu.
5. Touch the Password eld to open an on-screen keyboard, which can
be used to enter the password.
4. Reattach the battery compartment cover by pressing down lightly on
the locking tab, while sliding the cover into place.
DO Congure the Touch Screen Remote
The main menu is the starting point for conguring the TSR-302 from
Crestron®. If no project is loaded, touch the screen to access the main
menu. If a project is running, the main menu can be accessed by pressing
(Power), (Home), MENU, and GUIDE on the TSR-302 in sequence twice
( , , MENU, GUIDE, , , MENU, GUIDE) within a 5 second period.
The main menu can also be accessed via Crestron Toolbox™:
1. Establish communication with the TSR-302.
2. Right-click on the device and select Functions > Setup Mode.
1. Use a stylus or other thin-tipped object to press ACQUIRE on
the CEN(I)-ERFGW-POE gateway to enter Acquire mode. The
accompanying LED illuminates, indicating the unit is ready to link with
the touch screen. (The gateway can also be put into Acquire mode via
Crestron Toolbox.)
2. From the main menu on the TSR-302, touch RF Setup to display the
RF Setup menu. Then place the TSR-302 in Acquire mode by touching
Acquire on the RF Setup menu. The screen displays an “Acquire in
progress” message and the TSR-302 is automatically acquired by the
gateway within 2 minutes.
6. Touch Save to save the password and return to the Conrm Info menu.
Otherwise, perform the following steps to add a new access point.
1. Touch Add New to display the Conrm Info menu.
Page 2
7. Touch Make this my Access Point to conrm the entries and display
the WAP Connec t menu.
8. Touch Done to accept the connection to the wireless access point and
to display the WiFi Setup win dow.
10. To use DHCP, touch repeatedly to return to the main menu.
11. To enter static IP settings, touch Off under DHCP Enabled. The
TSR-302 ships with DHCP enabled by default.
12. Touch Set Static IP Address Settings to display the Static IPs menu.
14. Enter the address and touch Save to return to the Static IPs menu.
15. Touch each of the rest of the elds in turn and enter its address, and then touch Save.
16. Touch to return to the WiFi IP Settings menu.
17. Touch Reboot Required to Apply IP Changes.
9. Touch IP Settings to display the WiFi IP Settings menu.
13. Touch the Static IP address eld to open an on-screen numeric
keypad.
As of the date o f manufacture, th e TSR-30 2 has been tested an d found to comply with s pecications f or CE mark ing.
Federal Communications Commission (FCC) Compliance Statement
This devi ce compl ies with p art 15 of the FCC R ules. Operatio n is subject to the foll owing condition s:
(1) This device m ay not cause harmf ul inter ference and (2) this d evice must accept a ny interferenc e received, inclu ding inte rfere nce that may cause un desired operat ion.
CAUTION: Changes or mo dicati ons not expressl y approve d by the manu facture r responsible fo r compli ance cou ld void the u ser’s auth ority to o perate th e equipment.
NOTE: This eq uipment has bee n tested an d found to comply with t he limits f or a Class B digital d evice, pu rsuant t o part 15 of the F CC Rules. T hese limits are de signed to provide re asonable prote ction against ha rmful in terfer ence in a resident ial
install ation. This equip ment generates , uses an d can radi ate radio f requen cy energy and, if not i nstalled and use d in accordance w ith the ins tructi ons, may c ause har mful interfere nce to radi o communication s. However, there is no gua rantee th at
interf erence w ill not occur in a par ticular instal lation. If t his equipment do es cause h armful interfe rence to radio or tel evision r eception, which c an be determined by t urning t he equip ment off a nd on, the user is enc ouraged to try to co rrect the
interf erence b y one or mor e of the follow ing measures:
Reori ent or reloca te the r eceiv ing antenna
• Increa se the sep aratio n betwee n the equipment an d receive r
• Connec t the equipment into a n outlet on a circui t differ ent from that to which t he receiver is con nected
• Consul t the deale r or an experienc ed radio /TV te chnician for hel p
Industry Canada (IC) Compliance Statement
This devi ce compl ies with I ndustr y Canada license -exempt RSS stan dard(s). Operatio n is subject to the fol lowing two c onditions: (1) this devi ce may not cause inte rfere nce and (2) th is device must acc ept any inte rference, inc luding in terfe rence tha t
may cause u ndesired oper ation of th e device.
Under In dustr y Canada re gulations, this r adio transmitt er may only o perate using an an tenna of a ty pe and maximum (or l esser) gain app roved for th e transmitter by In dustry Canada . To reduce pot ential r adio inte rfere nce to othe r users , the anten na
type an d its gain s hould be s o chosen t hat the equ ivalent isotrop ically r adiated p ower (e.i.r.p.) is not more than th at necessar y for succ essful c ommunication.
DO Learn More
Check the website for the latest rmware updates.
www.crestron.com
Crestron Electronics 15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
Industrie Canada (IC) Déclaration de conformité
Le prése nt appareil est co nforme aux CNR d’Ind ustrie Canada ap plicab les aux ap pareil s radio exem pts de lic ence. L’exploitatio n est autorisée au x deux condition s suivante s : (1) l’appareil n e doit pas p roduire de brouill age, et (2) l’utilisate ur de
l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Conform ément à la régleme ntation d’Indus trie Can ada, le pr ésent ém etteur radio peu t fonctionner ave c une anten ne d’un typ e et d’un gain m axima l (ou inféri eur) approuvé pou r l’émette ur par Ind ustrie C anada. D ans le but de réduir e les risq ues de
brouill age radi oélect rique à l’intention de s autres utilisa teurs, il f aut choisir le typ e d’antenne e t son gain de sorte q ue la puis sance is otrope rayonnée é quivalente (p.i.r.e.) ne dé passe pa s l’intensité néces saire à l’établisse ment d’une communi cation
satisfaisante.
To satisfy RF e xposur e require ments, this devic e and its antenna mus t operate with a sep aration d istance of at leas t 20 centimeters fr om all persona an d must not b e coloca ted in con junctio n with any other anten na or transmitte r. For opera tion
within th e 5.15-5.25 GHz ban d, it is restricted t o indoor u se.
The specic patents that cover Crestron products are listed at patents.crestron.com. Product warranty can be found at www.crestron.com/warranty.
Crestr on, the Cre stron lo go, and Cre stron Toolb ox are eithe r trademar ks or registered tra demarks of C restron Electr onics, In c. in the Unit ed States and/or ot her countries. Wi- Fi and WPA2 are eit her trademarks or re gistered t rademarks of Wi-F i Alliance in the Unite d States a nd/or other countr ies.
Other tr ademarks, regist ered trademarks, a nd trade names may be use d in this document to ref er to either the entit ies claiming the marks a nd names or their produ cts. Crestron d isclaims any proprie tary interest in t he marks and names of o thers. Crestro n is not responsible fo r errors in typog raphy
or photography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2014 Crestron Electronics, Inc.
DO GUIDE
DOC. 7661A (204 0912) 08.14
Specic ations subject to c hange without not ice.
Loading...