TS-770/TS-1070
PRELIMINARY
7 in. and 10.1 in. Surface Mount TouchScreens
QuickStart
The Crestron® TS-770 and TS-1070 are surface mount touch screens that
feature web browsing, Smart Graphics® software and HTML5
UItechnology, custom-programmable icons, H.265/H.264 streaming
video, a Rava® SIPintercom, Wi-Fi® network connectivity, and PoE+
(Power over Ethernet Plus)network power. The touch screens also
provide built-in applications for room scheduling, conferencing, and home
control.
The TS-770 and TS-1070 are functionally similar. For simplicity within this
guide, the term "touch screen"is used except where noted.
In the Box
TS-770 or TS-1070*, Surface Mount TouchScreens
1
Additional Items
# Item (#######)
# Item (#######)
# Item (#######)
* Refer to the TS-770-B-S and TS-1070-B-S product pages at www.crestron.com for a
complete list of color variations.
TS-770 Only
# Item (#######)
# Item (#######)
# Item (#######)
# Item (#######)
TS-1070 Only
# Item (#######)
# Item (#######)
# Item (#######)
# Item (#######)
1
TS-770/TS-1070
PRELIMINARY
7 in. and 10.1 in. Surface Mount TouchScreens
QuickStart
Place the TouchScreen
The touch screen may be placed on any flat, level surface such as a desk,
conference table, lectern, or podium. The rubber strips on the bottom of
the touch screen prevent it from moving easily.
Connect the Touch Screen
Route all necessary cables to the touch screen, and then make
connections to the bottom of the touch screen as shown in the
illustration below.
Observe the following when connecting the touch screen:
l Power and data connection is provided to the touch screen by a single
Ethernet cable. A Crestron PoE (Power over Ethernet) power supply,
such as the PWE-4803RU, or a PoE-capable network switch is
recommended (both not included).
l The USB ports are used to connect compatible Crestron LED
accessories to the touch screen.
NOTE: The TS-770 may use either PoE or PoE+ to supply power to
compatible LED accessories over USB; the TS-1070 must use only
PoE+ to supply power to LED accessories over USB.
l Apply power after all connections have been made.
2
TS-770/TS-1070
PRELIMINARY
7 in. and 10.1 in. Surface Mount TouchScreens
QuickStart
TBD
Install the Cable Grommet
Configure the Touch Screen
When power is applied for the first time, the following screen is displayed.
The touch screen may take up to two minutes to boot.
3
TS-770/TS-1070
PRELIMINARY
7 in. and 10.1 in. Surface Mount TouchScreens
QuickStart
Touch the screen to display the main Setup screen (TSW-1070 shown).
Device settings for the touch screen may be configured using the built-in
setup screens or the web configuration interface. For more information
on configuring the touch screen, refer to the TS-770/TS-1070
Supplemental Guide (Doc.8555) at www.crestron.com/manuals.
Access the Device Setup Screens
To access the built-in setup screens, place five fingers on the display and
hold for 15 seconds.
Access the WebConfiguration Interface
The touch screen provides a web configuration interface that is used to
view and configure various touch screen settings and to select an
application. The interface can be accessed using the touch screen IP
address or the Crestron XiO Cloud™ service.
Touch Screen IPAddress
To access the web configuration interface using the touch screen IP
address:
1. Ensure that the touch screen is connected to the network.
2. Use the Device Discovery tool in Crestron Toolbox™ software to
discover the touch screen and its IP address on the network.
3. Enter the touch screen IP address into a web browser.
Crestron XiOCloud Service
The Crestron XiO Cloud service allows supported Crestron devices across
an enterprise to be managed and configured from one central and secure
location in the cloud. Supported devices are configured to connect to the
service. Use of the service requires a registered Crestron XiOCloud
account.
NOTE:The device may be disconnected from the service by navigating
to the Cloud Services tab in Crestron Toolbox software (Functions >
Device Info > Cloud Services). For details, refer to the Crestron
Toolbox help file.
Use the setup screens to configure various settings for the touch screen,
including Ethernet setup, IP table setup, audio setup, display setup,
standby timeout, application selection, Wi-Fi network setup, diagnostics,
the Bluetooth™ beacon, and the virtual toolbar.
4
TS-770/TS-1070
PRELIMINARY
7 in. and 10.1 in. Surface Mount TouchScreens
To access the web configuration interface using the Crestron XiOCloud
service:
QuickStart
1. Record the MAC address and serial number that are labeled on the
shipping box or rear panel of the device. The MAC address and serial
number are required to add the device to the service.
2. Do either of the following:
l For existing accounts, access the Crestron XiO Cloud service at
https://portal.crestron.io.
l For new accounts, register for a Crestron XiO Cloud account at
www.crestron.com/xio-cloud-registration.
3. Claim the device to the service as described in the Crestron XiO Cloud
User Guide (Doc. 8214) at www.crestron.com/manuals.
4. Select the device from the cloud interface to view its settings.
Set the Time Zone
The time zone must be set on the touch screen if it will not be paired with
a control system IPtable.
To set the time zone:
1. Access the web configuration interface using either the touch screen
IP address or the Crestron XiO Cloud service.
2. Select the Settings tab.
3. Navigate to System Setup >Time/Date.
4. Select the time zone where the touch screen will be used from the Time
Zone drop-down menu.
5. Click Save Changes on the top right of the screen.
Visit the Product Pages
Scan the QR code to visit the product page.
TS-770
www.crestron.com/model/6510820
TS-1070
www.crestron.com/model/6510821
5
TS-770/TS-1070
PRELIMINARY
7 in. and 10.1 in. Surface Mount TouchScreens
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron Toolbox, Crestron XiO Cloud, Rava, and Smart
Graphics are either trademarks or registered trademarks of Crestron Electronics, Inc.
in the United States and/or other countries. Bluetooth is either a trademark or
registered trademark of Bluetooth SIG, Inc. in the United States and/or other
countries. Wi-Fi is either a trademark or registered trademark of Wi-Fi Alliance in the
United States and/or other countries. Other trademarks, registered trademarks, and
trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not responsible for errors in typography or
photography.
©2020 Crestron Electronics, Inc.
Doc ID 8556A
(2054676)
QuickStart
02/06/20
6
Loading...