Crestron TPSBLOCK-10 User Manual

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
©2002 Crestron Electronics, Inc.
Crestron TPSBLOCK-10 10-Position RJ45 Panel Mount Interface
Contents
10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 1
Introduction........................................................................................................1
Industry Compliance..........................................................................................3
Installation..........................................................................................................3
Custom Adapter Plates.......................................................................................5
Further Inquiries.................................................................................................6
Return and Warranty Policies ............................................................................7
Merchandise Returns / Repair Service...................................................7
CRESTRON Limited Warranty.............................................................7
Installation Guide - DOC. 5979A 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 i
Crestron TPSBLOCK-10 10-Position RJ45 Panel Mount Interface
10-Position RJ45 Panel Mount Interface: TPSBLOCK-10

Introduction

The TPSBLOCK-10 is a 10-position RJ45 panel mount interface for Crestron Isys™ tilt touchpanels. The TPSBLOCK-10 is an electrically and magnetically shielded 10-position, female RJ45 connector mounted on a printed circuit board (PCB) and a 10-foot cable with a 10-position RJ45 plug (male).
This interface is designed to provide a lengthy 10-foot connection between the NET/VIDEO or RGB output from the TPS-IMC tucked away in a cabinet or under a table to the Isys touchpanel, which is available to the user. When installed into a panel or desktop pop-up/tilt­up device, the TPSBLOCK-10 provides local access by extending the touchpanel NET/VIDEO port and/or RGB port(s). The RGB port may be interfaced only when the touchpanel is equipped with an optional TPS-XVGA-BV RGB Computer Interface Card with Balanced Video. To interface the touchpanel NET/VIDEO and RGB ports, two TPSBLOCK-10s must be utilized.
Functional Summary
Handy 10-pin male connector and 10-foot cable interface
The touchpanel NET/VIDEO or RGB cable (supplied with the touchpanel) is connected to the female connector of the TPSBLOCK-10 and the TPSBLOCK-10 plug is connected to the Cresnet control system (via Crestron TPS interface module or optional TPS wall-mounted
Installation Guide - DOC. 5979A 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 1
solution for Isys™ TPS-Series advanced touchpanels
Easy mounting into a standard Extron/Altinex/Inline type interface plate
Plug-in socket for the “ship-with” Net/Video or RGB cable from a TPS-Series touchpanel
10-Position RJ45 Panel Mount Interface Crestron TPSBLOCK-10
OC. #
p
interface module). Refer to the table below for touchpanel and interface modules that are used with the TPSBLOCK-10.
TPSBLOCK-10 Interface Applications
TM
ISYS
TOUCHPANEL
TPS-4500
TPS-5000 &
TPS-6000
The TPS-IMC-BV is supplied with the optional TPS-XVGA-BV card that can only be installed
*
into specific touchpanels. Refer to the TPS-XVGA-BV Operations & Installation Guide for further information.
INTERFACE MODULE MODULE TPSBLOCK-10
MODULE AVAILABILITY
TPS-4500IMC
TPS-4500IMW
TPS-IMC
TPS-IMC-BV Sold Separately * 5921
TPS-IMW
Supplied
w/touchpanel
Sold Separately
Supplied
w/touch
Sold Separately
anel
D
5890 NET/VIDEO only
5913 NET/VIDEO only
5856 NET/VIDEO only
5857 NET/VIDEO only
INTERFACE
NET/VIDEO or
RGB
NOTE: For more information about the Crestron TPS interface or wall­mounted interface module(s), refer to the latest revision of the appropriate operations guide. The latest version can be obtained from the Downloads | Product Manuals section of the Crestron website (www.crestron.com
).
Refer to the table below for the pinouts of the TPSBLOCK-10 connector during NET/VIDEO and RGB applications. Pin 1 of the female connector is wired to pin 1 of the plug.
Connector/Plug Pinouts
PIN
1 * 2 3 4 5 6 7 8 9 10
While facing the female connector of the TPSBLOCK-10, pin 1 is located at the upper-left of
*
the connector.
DESIGNATION
+24V
GND
C+
C-
Y Z
Y+
Y-
GND
+24V Power (Network)
NET/VIDEO
DESCRIPTION DESCRIPTION
Power (Network) Vertical sync -
Ground (Network) Horizontal sync -
Chrominance (Positive) RED video -
Chrominance (Negative) RED video +
Data (Network) GREEN video ­Data (Network) GREEN video +
Luminance (Positive)/Composite
Luminance (Negative)/Composite
Ground (Network) Horizontal sync +
RGB
BLUE video -
BLUE video +
Vertical sync +
2 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 Installation Guide - DOC. 5979A
Crestron TPSBLOCK-10 10-Position RJ45 Panel Mount Interface
Peel-and-stick NET/VIDEO and RGB labels are supplied with the TPSBLOCK-10. If desired, a label may be affixed to the surface of the panel or desktop pop-up/tilt-up device. A matching AUDIO label is also supplied for use with non-Crestron 8-position RJ45 interface devices.

Industry Compliance

As of the date of manufacture, the TPSBLOCK-10 have been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling (N11785).

Installation

The items required for installation of the TPSBLOCK-10 are appropriate cutting tools to create the rectangular cut-out area in the panel or desktop pop-up/tilt-up device, a 0.136-inch (#29 or approximately 9/64-inch) drill bit, electric drill and two #4-40 screws of adequate length with an appropriate screwdriver. Refer to the following diagrams and perform the procedure that begins on the next page.
Overhead View
0.162 in
(0.412 cm)
1.210 in
(3.073 cm)
1.408 in
(3.576 cm)
MOUNTING BRACKETS
CABLE
MALE
RJ45 PLUG
10 ft
Front View
Pin 1
(Reference Only)
FEMALE RJ45
0.687 in
(1.745 cm)
CONNECTOR & PCB
Installation Guide - DOC. 5979A 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 3
10-Position RJ45 Panel Mount Interface Crestron TPSBLOCK-10
NOTE: The recommended clearance on each side of the rectangular cutout area is approximately 0.268 in (0.681 cm). The clearance at the bottom of the cutout area should be approximately 0.180 in (0.457 cm). The clearance above the cutout area is zero.
NOTE: If affixing a NET/VIDEO or RGB label near the TPSBLOCK­10 (above or below is recommended), a 0.200 in (0.508 cm) by 0.700 in (1.778 cm) area is required.
NOTE: Extron has made available Architectural Adapter Plates (AAPs) for mounting the TPSBLOCK-10 for Cresnet touchpanel connection. Refer to “Custom Adapter Plates” on page 5 for details. If using AAPs, skip steps 2 and 3 in the subsequent procedure.
1. On the panel or desktop pop-up/tilt-up device, determine an adequate location for the TPSBLOCK-10.
2. Refer to the diagram below. Using the proper tools, cut-out and remove the rectangular area from the panel or desktop pop-up/tilt-up device.
TPSBLOCK-10 Installation (1 of 3) - Cutout Diagram
0.675 in
(1.715 cm)
0.590 in
(1.500 cm)
3. Refer to the diagram below. Using an electric drill and
0.136-inch (#29 or approximately 9/64-inch) drill bit, drill two TPSBLOCK-10 mounting holes.
TPSBLOCK-10 Installation (2 of 3) - Mounting Hole Diagram
0.313 in
(0.795 cm)
0.143 in
(0.362 cm)
0.276 in
(0.701 cm)
0.136 in
DIAMETER
4. At the inner surface of the panel or desktop pop-up/tilt-up device, position the female connector of the TPSBLOCK-10
4 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 Installation Guide - DOC. 5979A
Crestron TPSBLOCK-10 10-Position RJ45 Panel Mount Interface
into the cutout area and align the drilled mounting holes with the TPSBLOCK-10 mounting brackets.
5. Refer to the diagram below. At the outer surface of the panel or desktop pop-up/tilt-up device, loosely install two #4-40 screws of adequate length (not supplied) through the surface into the TPSBLOCK-10 mounting brackets. Tighten screws to finger-tight then, using an appropriate screwdriver, tighten to a torque that is adequate for the surface material.
TPSBLOCK-10 Installation (3 of 3) - Secure TPSBLOCK-10
6. Connect the male RJ45 plug of the TPSBLOCK-10 cable to the NET/VIDEO or RGB port of the TPS interface module or TPS wall-mounted interface module.
7. If desired, peel the appropriate NET/VIDEO or RGB label (supplied) from the paper backing and affix to the surface of the panel or desktop pop-up/tilt-up device near (above or below is recommended) the TPSBLOCK-10.
8. At the outer surface of the panel or desktop pop-up/tilt-up device, connect the touchpanel NET/VIDEO or RGB cable (supplied with touchpanel) to the female RJ45 connector of the TPSBLOCK-10.

Custom Adapter Plates

Extron Architectural Adapter Plates (AAPs), shown on the next page, are available for mounting Crestron TPSBLOCK-10 for touchpanel connection. These two-space AAPs allow the mounting of one or two TPSBLOCK-10 interfaces. The AAPs must be ordered separately from Extron; consult the Extron website (www.extron.com) for specifications and ordering details.
Installation Guide - DOC. 5979A 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 5
10-Position RJ45 Panel Mount Interface Crestron TPSBLOCK-10
Extron Architectural Adapter Plates (AAPs)

Further Inquiries

If after reviewing this Installation Guide, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling:
In the US and Canada, call Crestron’s corporate headquarters at 1-888-CRESTRON [1-888-273-7876] or 1-201-767-3400.
In Europe, call Crestron International at +32-15-50-99-50.
In Asia, call Crestron Asia at +852-2341-2016.
In Latin America, call Crestron Latin America at
+5255-5093-2160.
In Australia and New Zealand, call Creston Pacific at +613-9480-2999.
6 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 Installation Guide - DOC. 5979A
Crestron TPSBLOCK-10 10-Position RJ45 Panel Mount Interface

Return and Warranty Policies

Merchandise Returns / Repair Service

1. No merchandise may be returned for credit, exchange, or service without prior
authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address.
2. Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, Cresskill, N.J., or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by
CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser.

CRESTRON Limited Warranty

CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three (3) years from the date of purchase from CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and overlay components are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. Furthermore, this warranty does not cover any product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supercedes all previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered trademark of Microsoft Corporation. Windows95/98/Me and WindowsNT/2000 are trademarks of Microsoft Corporation.
Installation Guide - DOC. 5979A 10-Position RJ45 Panel Mount Interface: TPSBLOCK-10 7
Crestron Electronics, Inc. Installation Guide - DOC. 5979A
15 Volvo Drive Rockleigh, NJ 07647 08.02 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.
Loading...