Page 1
DO GUIDE
TSR-302
Handheld Touch Screen Remote
DO Check the Box
QUANTITY PRODUCT COLOR PART NUMBER
1 Battery Pack, Rechargeable, TSR-302-BTP 2039523
1 Dock, Table, TSR-302-DS 4520465
1 Power Pack, 19 Vdc, 0.9 A, 100-240 Vac 2045868
DO Install the Battery
To install the TSR-302-BTP, perform the following procedure:
1. Remove the battery compartment cover on the rear of the TSR-302
by using two thumbs and gently pressing in the direction of the arrow
shown.
2. Place the touch screen remote, with the screen side down, on a clean,
soft surface.
3. Place the TSR-302-BTP in the battery compartment, oriented as
shown.
4. Reattach the battery compartment cover by pressing down lightly on
the locking tab while sliding the cover into place.
3. Select Enter Setup Mode to display the main setup screen.
NOTE: Select Exit Setup Mode to exit the setup screens.
NOTE: From any of the setup screens, tap to go back to the
previous screen.
For details on conguring the TSR-302, refer to Doc. 7663 at
www.crestron.com/manuals.
DO Set Up Basic Wireless
Before a TSR-302 can be used with a Crestron control system, it must rst
be acquired by a Crestron Extended Range (ER) Wireless Gateway (sold
separately).
To acquire a TSR-302, perform the following procedure:
1. Use a stylus or other thin-tipped object to press ACQUIRE on the
gateway to enter Acquire mode. The accompanying LED illuminates,
indicating the unit is ready to link with the touch screen. (The gateway
can also be put into Acquire mode via Crestron Toolbox.)
2. From the main setup screen on the TSR-302, tap RF Setup to display
the RF Setup screen. At the bottom of the RF Setup screen, select
2-Series or 3-Series, depending on whether a 2-Series or 3-Series®
control system is being used. Then place the TSR-302 in Acquire
mode by tapping Acquire on the RF Setup screen. The screen
displays an “Acquire in progress” message, and the TSR-302 is
automatically acquired by the gateway within 2 minutes.
3. When the process is complete, the screen displays an “Acquire OK”
message. Press ACQUIRE on the gateway to exit Acquire mode. The
LED turns off.
For information on wireless setup with roaming, refer to “Gateway Roaming
Setup” in Doc. 7663.
DO Set Up Wi-Fi
To set up a Wi-Fi® connection, on the main setup screen tap WiFi Setup,
and then tap Add Access Point to display the Select Access Point
screen.
If the desired wireless access point is already on the list, tap Connect.
Otherwise, perform the following procedure to add a new access point:
1. Tap Add New to display the Conrm Info screen.
2. Tap the WAP Name (SSID) eld to open an on-screen keyboard,
which can be used to enter the name.
3. Tap the Security eld to display the Encryption screen.
4. Select the appropriate type of encryption, and then tap to return
to the Conrm Info screen.
5. Tap the Password eld to open an on-screen keyboard, which can be
used to enter the password.
6. Tap Save to save the password and return to the Conrm Info
screen.
DO Congure the Device
The main setup screen is the starting point for conguring the Crestron
TSR-302. If no project is loaded, tap the screen to access the main setup
screen. If a project is running, the main setup screen can be accessed by
pressing (Power), (Home), MENU, and GUIDE in sequence twice
( , , MENU, GUIDE, , , MENU, GUIDE) within a 5-second
period.
The main setup screen can also be accessed via Crestron Toolbox™
software.
1. Establish communication with the TSR-302.
2. Right-click on the device and select Functions > Setup Mode.
®
Page 2
7. Tap Make this my Access Point to conrm the entries and display
the WAP Connect screen.
8. Tap Done to accept the connection to the wireless access point and
to display the WiFi Setup screen.
10. To use DHCP, tap repeatedly to return to the main setup screen.
11. To enter static IP settings, tap Off under DHCP Enabled. The
TSR-302 ships with DHCP enabled by default.
12. Tap Set Static IP Address Settings to display the Static IPs screen.
14. Enter the address and tap Save to return to the Static IPs screen.
15. Tap each of the rest of the elds in turn and enter its address, and then
tap Save.
16. Tap to return to the WiFi IP Settings screen.
17. Ta p Reboot Required to Apply IP Changes.
9. Tap IP Settings to display the WiFi IP Settings screen.
13. Tap the Static IP address eld to open an on-screen, numeric
keypad.
As of the date of manufacture, the pr oduct has been teste d and found to c omply with s pecications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with par t 15 of the FCC Rule s. Operation is subject to the following two co nditions:
(1) This devic e may not caus e harmful i nterference, and (2) this device m ust accept any inter ference received, including interfer ence that may cause und esired op eration.
CAUTION: Changes or modicat ions not expressly ap proved by the manufactu rer responsible for compliance could void the user’s au thority to operate the equipment.
NOTE: This equipment has been te sted and found to comply with the limi ts for a Class B digital device, pursuant to par t 15 of the FCC Rule s. These li mits are designed to pr ovide reas onable pr otection
agains t harmful interference in a residential installation. This equipment generates, uses an d can radia te radio fre quency energy and, if not installed and use d in accord ance with the instruc tions, may
cause harmful interference to radio communications. However, there is no guarantee th at interference will not occur i n a partic ular installation.
If this equipment do es cause harmful interference to radio or televisio n reception, which ca n be determined by turning the equipment off and on, the user is encou raged to tr y to correct the inter ference
by one or more of the following measu res:
• Reorient or relocate the receiving antenna
• Increase the sepa ration between the e quipment and receiver
• Connect the equip ment into an o utlet on a circuit different fro m that to which the receiver is conne cted
• Consult the deale r or an exper ienced radio/T V technician for help
Industry Canada (IC) Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is s ubject to th e following t wo conditions: (1) this device may not cause interference and (2) this devic e must acce pt
any inter ferenc e, including interference that may cause undesired operation of the devic e.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn more about this product, use a QR reader application on
your mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
Under Industry Canada regulations, this radio transmit ter may only o perate using an antenna of a type an d maximum (or lesser) gain appr oved for the tr ansmitter by Industry Canada. To reduce pote ntial
radio interfere nce to other u sers, the antenna type and its gain should b e so chosen that the equi valent isotropically radiate d power (e.i.r.p.) is not more than that necess ary for successf ul communication.
Industrie Canada (IC) Déclaration de conformité
Le présent appareil est conforme aux CN R d’Industrie Canada a pplicables aux appareils radio exempts de licence. L’exploitation est autorisée aux d eux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Confor mément à la r églemen tation d’Industrie Canada, le p résent ém etteur ra dio peut fonctionne r avec une ante nne d’un type et d’un gain ma ximal (ou inférieur) approuvé pour l’émetteur par Indus trie
Canada . Dans le but de réduire les risque s de brouill age radioélectrique à l’intenti on des autres utilisa teurs, il faut choisi r le type d’ante nne et son gain de sorte q ue la puiss ance isotrope rayonnée
équivalente (p.i.r.e.) ne dé passe pas l’intensité nécessa ire à l’établis sement d’une communi cation satisfaisa nte.
To satisfy R F exposure requirem ents, this device and i ts antenna must oper ate with a separat ion distance of at lea st 20 centimeters f rom all persona and mu st not be colocated in c onjunction with an y other antenna or tra nsmitter. For opera tion within the 5.15-5.2 5 GHz band, it is rest ricted to
indoor use.
Crestr on product developm ent softwar e is licensed to Cres tron dealers and Cr estron Servi ce Providers (C SPs) under a limited no n-exclusive, non-t ransferable S oftware Devel opment Tools License A greement. Crest ron product oper ating system sof tware is licens ed to Crestron dea lers, CSPs,
and end-us ers under a separa te End-User Lic ense Agreement. B oth of these Agree ments can be found on t he Crestron webs ite at www.crestron.com/legal/sof tware_license_agreement.
The speci c patents that c over Crestron pro ducts are listed a t patents.crestron.com. The produ ct warranty ca n be found at www.crestron.com/warranty.
Crestr on, the Crestron lo go, 3-Series, Cr estron Toolbox, and in NET EX are e ither trademarks o r registered trade marks of Crestro n Electronics, I nc., in the United St ates and/or other c ountries. Wi-F i, WPA and WPA2 are e ither trademarks o r registered trad emarks of Wi-Fi A lliance in the United
States a nd/or other count ries. Other tradem arks, registered t rademarks, and tr ade names may be used in this d ocument to refer to eit her the entities cla iming the marks and name s or their products. C restron disclaim s any proprietary i nterest in the marks a nd names of others. C restron is not
responsi ble for errors in t ypography or phot ography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2016 Crestron Electronics, Inc.
DO GUIDE
DOC. 76 61C (2040 912) 02.16
Specic ations subject to c hange without not ice.
Loading...