Page 1
DO GUIDE
A
BALANCED AUDIO INPUT:
SAROS SB-200-P
Saros® Sound Bar 200, Powered
DO Install the Device
The Saros® Sound Bar can be installed as part of a Crestron RL® 2 Group Collaboration system or
on a wall as part of any integrated audio system. With the balanced and unbalanced inputs, the
sound bar can work with any audio system.
In a Crestron RL System
Use the included thumb screws to attach the sound bar to the sound bar bracket. Refer to the
quickstart included with the Crestron RL Group Collaboration system for details.
On a Wall
1. Place the mounting bracket on the wall.
NOTE: Use a laser level or snap a chalk line to mark the location of the bracket.
2. Secure the bracket to the wall with hardware that is appropriate for the mounting surface.
DO Check the Box
QTY PRODUCT COLOR PART NUM.
1 Bracket, Mounting 2048193
1 Cable, RCA®, Right-Angle, 6' (1.83 m) Black 2047013
1 Connector, 5-Pin 2047025
1 Power Cord, 6' (1.83 m) Black 2047024
2 Screw, 6-32, Thumb 2047009
3. Install the included thumb screws on the rear of the sound bar.
4. Connect the sound bar as described in “DO Connect the Device.”
5. Place the sound bar against the wall, above the mounting bracket, and lower the sound bar until
the thumb screws rest in the mounting bracket.
B
DIMENSION INCHES MILLIMETERS
NOTE: If a stud cannot be located, use the screwholes located adjacent to each keyhole slot.
C
D
E
F
G
H
I
J
K
L
A 26.8 680
B 23.3 592
C 21.3 540
D 18.6 472
E 16. 5 420
F 13.9 352
G 11. 8 300
H 9.1 232
I 7.1 180
J 4.4 112
K 2.4 60
L 0.3 8
DO Connect the Device
Make the necessary connections as called out in the diagram below. Connect power last.
From balanced audio source
UNBALANCED AUDIO INPUT:
From unbalanced audio source
NOTE: Connect only one input.
NOTE: If using the included RCA® cable for connecting the UNBALANCED port, use the right-
angled connectors to allow the cable to t between the wall and the sound bar.
100–240V~ 50/60Hz 50W:
From ac power outlet
DO Use the Device
Move the switch located above the 100–240V~ 50/60Hz 50W port to turn on the sound bar. The PWR
LED lights, and sound from the connected source is produced.
If an audio signal is not present for approximately 20 minutes, the sound bar switches to a low power
idle state. The sound bar resumes normal operation when an audio signal is detected.
Page 2
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested a nd found to compl y with specic ations for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device com plies with par t 15 of the FCC Rules. Op erati on is subject to the following two conditi ons:
(1) This devic e may not cause harmful interferenc e, and (2) th is devic e must ac cept any inter ference received, includi ng interfere nce
that may cause undesired operation.
CAUTION: Changes or modication s not expressly approved by the manufacturer re sponsible fo r compl iance c ould voi d the
user’s authority to operate the e quipment.
NOTE: This equipment has been tested and found to comply with the lim its for a Class B digital device, pursuant to par t 15 of the
FCC Rules. Thes e limits are designed to p rovide r easonable protection against harmful interferenc e in a residenti al inst allation.
This equipment generates, uses and can rad iate rad io freq uency e nergy and, if not installed and used in a ccordance with the
instructions, may cause har mful interfe rence to radio communicatio ns. However, there is no guarantee that inter feren ce will not
occur in a particular installation.
DO GUIDE
If this equipment does c ause ha rmful i nterference to radio or television re ception, which can be d etermined by turning th e
equipment of f and on, the user is encou raged to try to correc t the inte rfer ence by one or more of the foll owing me asures:
• Reorient or relocate the receiving antenna.
• Increase the separ ation betwee n the equ ipment and rec eiver.
• Connect the e quipm ent into a n outlet on a circuit dif ferent from that to which the receiver is c onnec ted.
• Consult the dealer o r an experienc ed radio/T V tech nicia n for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Electrical Connection
“This produc t must be c onnected to an e arth ed mains socket-outlet.”
• Finland: “Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.”
• Norway: “Apparate t må tilkop les jor det stikkontakt.”
• Sweden: “Apparaten ska ll anslutas till jorda t utta g.”
The speci c patents that c over Crestron pro ducts are listed a t www.crestron.com/legal/patents. The produ ct warranty ca n be found at www.crestron.com/warranty.
Certa in Crestron pro ducts contain op en source soft ware. For speci c information, ple ase visit www.crestron.com/opensource.
Crestr on, the Cre stron lo go, Crest ron RL, a nd Saros a re either t rademark s or regist ered trad emarks of C restro n Electro nics, Inc . in the Unite d State s and/or ot her count ries. RC A is either a
trademar k or regist ered trad emark of VOX X International C orpora tion in the U nited St ates and/ or other cou ntries. O ther tr ademarks , register ed tradema rks, and t rade names m ay be used
in this docum ent to refer t o either the entitie s claiming the m arks and na mes or their pr oducts. Crestr on disclaims any propr ietary i nterest i n the marks a nd names of ot hers. Crestron is n ot
responsi ble for errors in t ypography or phot ography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2017 Cres tron Electroni cs, Inc.
DOC. 7508D (2 04 596 2) 08 .17
Specic ations subject to c hange without not ice.
Loading...