Crestron HD-XSP Quick Start Manual

Download

Page 1

HD-XSP

7.1 High-Definition Professional Surround Sound Processor

Introduction

The HD-XSP is a 7.1 surround sound processor featuring multiple inputs and downmixing capabilities.

Hardware Hookup

Connect the Device

Make connections to the HD-XSP as shown in the following diagram.

HDMI OUT:

To HDMI Device

quickstart guide

IN OUT

HDMI IN:

From HDMI Source

Connect Balanced/Unbalanced Input & Outputs

One balanced/unbalanced audio input and four balanced/unbalanced audio outputs are provided, utilizing 5-pin and 6-pin terminal block connectors respectively. For connection details, refer to the following diagrams.

Balanced Input

+ - + -G

Shield

From Digital Audio Sources

HDMI

DIGITAL BALANCED

INPUT:

From Unbalanced Analog

Audio Sources

Right

Left

DIGITAL:

5 6

INPUT

Balanced Output

+ - + -G

+ - + -G G

OUTPUT:

To Amplifiers

MIX

FRONT L

+ - + -G G

SURROUND

+ - + -G G

INPUT:

From Balanced or Unbalanced

Analog Audio Source

Shield

Right

AMP

Left

OUTPUT

BACK

+ - + -G G

CENTER - SUB

+ - + -G G

DOWNMIX

+ - + -G G

Balanced Output (Center & Sub)

+ - + -G G

24V DC, 2.0A:

From AC Power Pack

MAC ID LABEL

SERIAL LABEL

—

24V

---

2.0A

LAN

LAN:

10BASE-T/100BASE-TX

Ethernet to Lan

Shield

Subwoofer

AMP

Center

Configuration

The HD-XSP can be configured with the front panel controls or with Crestron Toolbox™. For details on using Crestron Toolbox, please refer to the Crestron Toolbox help file. Otherwise, continue reading below.

The “Installer” menu is used to configure the HD-XSP’s inputs, outputs, network settings, and front panel controls. To open the “Installer” menu:

1. Press HOME to display the “Crestron HD-XSP” screen as shown in the following diagram.

Crestron

HD-XSP

2. Press BACK to display the “Password” screen.

Password

[0]000

3. Use the ˄, ˅, ˂, ˃, and SELECT buttons to enter the password.

• To select a number, press ˄ or ˅.

• To move the cursor left or right, press ˂ or ˃.

When the password is displayed, move the cursor to the rightmost digit and press SELECT. The “Installer” menu is displayed.

Installer

Inputs

Outputs

Network

Control

NOTE: The default password is 0000. For instructions on

changing the password, refer to “Password” in the latest version of the HD-XSP Operations & Installation Guide (Doc. 7446), which is available from the Crestron Web site (www.crestron.com/manuals).

HD-XSP

Unbalanced Input

+ - + -G

Shield

Right

Left

Unbalanced Output

+ - + -G G

(Continued in following column)

For details, refer to the latest revision of the HD-XSP Operations & Installation Guide, Doc. 7446.

QUICKSTART DOC. 7447A (2035044) 05.13

Unbalanced Output (Center & Sub)

+ - + -G G

The “Installer” menu is divided into four sections.

• Inputs: Set the name and compensation level of each input.

• Outputs: Set the audio parameters for the theater and downmix outputs.

• Network: Configure and view the HD-XSP’s Ethernet settings.

Right

AMP

Left

www.crestron.com

Specifications subject to change without notice.

Subwoofer

Center

AMP

• Control: Configure and view the HD-XSP’s front panel settings.

For details, refer to the latest version of the HD-XSP Operations & Installation Guide (Doc. 7446).

888.273.7876 201.767.3400

Page 2

HD-XSP

7.1 High-Definition Professional Surround Sound Processor

Operation

When power is applied to the HD-XSP, the title screen displays, followed by the “Current Source” menu. The “Current Source” menu is used to select a source and a decoding mode.

Select a Source or Decoding Mode

To select a source or decoding mode:

NOTE: The “Current Source” menu is displayed when power is applied to the HD-XSP.

1. Press HOME.

2. Press SELECT. The “HD-XSP” menu is displayed.

HD-XSP

Source

quickstart guide

Theater

Downmix

Display Off

3. Press ˄ or ˅ to highlight Source and press SELECT. The “Current Source” menu is displayed.

Current Source

Source Select

Decoding Mode

None

Select a Source:

1. Press ˄ or ˅ to highlight Source Select and press SELECT. The “Source Select” menu is displayed.

Source Select

HDMI

Optical

Coaxial 1

Coaxial 2

2. Press ˄ or ˅ to highlight the desired source and press SELECT. The “Current Source” menu is displayed. If a signal type is detected, the supported signal type is shown on the bottom of the display.

Current Source

HDMI

Decoding Mode

Dolby Digital

Operation (continued)

Select a Decoding Mode:

1. Press ˄ or ˅ to highlight Decoding Mode and press SELECT. The “Decoding Mode” menu is displayed, showing a list of supported decoding modes for the detected audio signal.

Decoding Mode

None

Auto

Dolby PLIIx Movie

Dolby PLIIx Music

2. Press ˄ or ˅ to highlight the desired mode and press SELECT. The display returns to the “Current Source” menu showing the selected source and the selected decoding mode.

Current Source

HDMI

Decoding Mode

Dolby Digital

Volume Control & Mute (Theater Output Only)

During operation, the theater output’s volume level can be adjusted or muted.

• To adjust the theater output’s volume level, Press VOL ˄ or VOL ˅.

• To mute the theater output, press MUTE. An indicator lights on the bottom of the display.

• To unmute the theater output press MUTE.

Additional Functions

Controls for the theater output, downmix output and display are available from the “HD-XSP” menu. For details, refer to the latest version of the HD-XSP Operations & Installation Guide (Doc. 7446).

The specific patents that cover Crestron products are listed at patents.crestron.com.

Crestron, the Crestron logo, and Crestron Toolbox are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is

not responsible for errors in typography or photography.

NOTE: The downmix output’s volume level is adjusted via control system programming.

NOTE: The downmix output’s mute function is controlled from the front panel. Refer to the

latest version of the HD-XSP Operations & Installation Guide (Doc. 7446) for details.

NOTE: The downmix output’s mute function is controlled from the front panel. Refer to the latest version of the HD-XSP Operations & Installation Guide (Doc. 7446) for details.

HD-XSP

For details, refer to the latest revision of the HD-XSP Operations & Installation Guide, Doc. 7446.

QUICKSTART DOC. 7447A (2035044) 05.13

www.crestron.com

Specifications subject to change without notice.

888.273.7876 201.767.3400