Page 1
DO GUIDE
HD-TX-201-C-2G-E
DM Lite Multiformat Switch and Transmitter
DO Install the Device
Install the device into a 2-gang electrical box (not included). A minimum mounting depth of 2 inches
(51 mm) is required.
To install the device:
1. On the rear of the device, make connections to the TO RX and Ethernet ports.
NOTES:
• For the 24 Vdc power connection, connect a power pack to either the transmitter or
a compatible receiver. Do not connect a power pack to both devices simultaneously.
Power is transmitted over the cable that connects the TO RX port on the transmitter to
the FROM RX port on the receiver.
A power pack is not included with the transmitter. When the transmitter is used with a
DM Lite surface-mount receiver, the transmitter receives power from the power pack
that ships with and connects to the receiver.
• Cabling that connects the TO RX port to the FROM TX port is designed for
intrabuilding use only.
DO Check the Box
QTY ITEM PART NUM.
4 Screw, 6-32 x 3/4", Truss Head, Combo 20 09211
2. Using a Phillips screwdriver (not included), attach the device to the electrical box using the
four included #6-32 x 3/4-inch truss combo head screws.
3. Attach a decorator-style faceplate (sold separately) to the front panel of the device using
four screws (not included).
TO RX:
To FROM TX
link input of
receiver
24 G
24 V
1.25 A:
From power pack
(not included)
:
Passive
pass-through
to front panel
Ethernet port
Page 2
DO Connect the Device
For factory
pass-through
From unbalanced
Connect the device as required for the application.
HDMI IN:
source
:
Passive
®
From HDMI
audio/video
to rear panel
Ethernet port
The SERVICE port is for factor y use only.
SERVICE:
VGA IN:
From RGB (VGA)
or component
video output
AUDIO IN:
stereo line level
audio output
DO Congure the Device
To congure the device, do either of the following:
• If the transmitter connects to an HD-RX-201-C-E, the HD-RX-201-C-E hosts the
conguration of the transmitter. As a result, congure the transmitter using the web
interface of the HD-RX-201-C-E.
To access the web interface, open a web browser and then go to the IP address of the
HD-RX-201-C-E. By default, DHCP is enabled. To display the IP address on the
connected HDMI® display, press the SETUP button on the front panel of the
HD-RX-201-C-E. Pressing the SETUP button on the transmitter will also display the
IP address of the HD-RX-201-C-E.
To log in to the web interface, enter the user name and password. The default user name
and password are both admin.
• If the transmitter does not connect to an HD-RX-201-C-E, refer to Answer ID 1000168
in the Online Help section of the Crestron website (www.crestron.com/onlinehelp) for
conguration information.
NOTE: When the transmitter does not connect to the HD-RX-201-C-E, pressing the
SETUP button on the transmitter has no effect.
use only
As of the date of manufacture, the product has been tested and found to co mply with speci cations for CE m arking.
®
This product is Listed to a pplicable UL
Ce produit est ho mologué selon les normes et le s exigen ces UL ap plicables pa r Under write rs Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies wi th par t 15 of the FCC Rules. Ope ration is subje ct to the following t wo condi tions:
(1) This devic e may not ca use har mful interference, a nd (2) this d evice mu st acce pt any inte rfer ence re ceived, including inte rference
that may cause undesired operation.
CAUTION: Changes or modic ations not expre ssly approved by the manufactur er resp onsible for com pliance could void the us er’s
author ity to op erate th e equipment.
NOTE: This equipm ent has b een tested and fo und to com ply with t he limit s for a Class B digit al devic e, purs uant to pa rt 15 of the
FCC Rules. These limits a re designed to pr ovide reasonable protection a gains t harmf ul inter ference in a residential installation.
This equipmen t gener ates, uses and can radiate radio f reque ncy energy and, i f not installed and used in accordance with the
instruction s, may cau se harmful inte rference to ra dio communica tions. H owever, there is no guar antee that inter fere nce will n ot
occur in a particular installation.
Standards and requir ements tested by U nder writers Laborator ies Inc.
DO GUIDE
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
If this equipment does cause har mful interfe rence to r adio or te levisi on rece ption, which can be deter mined by turning t he
equipment off and on, the user is e ncour aged to tr y to correct the interference by one or more of the fo llowing measures:
• Reorient or relocate the receiving antenna.
• Increase the se paration bet ween the e quipment and receive r.
• Connect the equipmen t into an outlet on a ci rcuit di fferent from that to which the rec eiver is c onnected.
• Consult the dealer or an experienced r adio/ TV technici an for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The speci c patents that c over Crestron pro ducts are listed a t www.crestron.com/legal/patents.
The produ ct warranty ca n be found at www.crestron.com/legal/sales-terms-conditions-warranties.
Certa in Crestron pro ducts contain op en source soft ware. For speci c information, vi sit www.crestron.com/legal/open-source-software.
Crestr on and the Cre stron lo go are eithe r trademar ks or regist ered trad emarks of Cr estron E lectroni cs, Inc., in t he United S tates and /or other countries . HDMI and t he HDMI l ogo are eith er
trademar ks or regis tered trad emarks of H DMI Lice nsing LLC in t he United States an d/or other c ountries. UL and th e UL logo are e ither tra demarks or r egistered t rademarks of Under writers
Labora tories, Inc. in the U nited States and /or other countrie s. Other trademar ks, registered tr ademarks, and trad e names may be used in this do cument to refer to eit her the entities clai ming
the marks a nd names or their prod ucts. Crestro n disclaims any propr ietary intere st in the marks and nam es of others. Cre stron is not respo nsible for errors in t ypography or ph otography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2018 Crestron Electronics, Inc.
DOC. 8333A ( 205 2143) 0 6.18
Specic ations subject to c hange without not ice.
Loading...