HD-RX-4K-510-C-E
4K Multiformat 5x1 AV Switch and Receiver
The Crestron® HD-RX-4K-510-C-E multiformat AV switch and
receiver provides enhanced HDMI® video switching and audio
presentation capabilities in areas such as conference rooms
and classrooms. Compatible with all DM Lite™ transmitters, the
HD-RX-4K-510-C-E provides three DM Lite inputs for
connection to up to three transmitters. A CATx (CAT5e or
higher) twisted pair cable connects a transmitter to the
HD-RX-4K-510-C-E for the transmission of HDMI signals.
Forresolutions up to 2K, the maximum transmission distance is
230ft (70m). Forhigher resolutions up to 4K, the maximum
transmission distance is 130ft (40m).
l
4K/60 4:2:0 capability
l
Three DM Lite™ ports for interoperability with up to three
DMLite transmitters
l
Two HDMI® inputs
l
One HDMI output with 4K scaler
l
Gigabit Ethernet port
l
Two stereo line level inputs, two mono microphone inputs,
and one mono auxiliary audio input
l
Built-in amplifier with 25 W per channel for 4- or 8-ohm
stereo speakers
l
Two stereo auxiliary outputs
l
IR, RS-232, relay, and I/O control ports
l
CEC (Consumer Electronics Control) capability
l
Automatic switching of inputs
l
6x2 audio mixing capability
l
EDID management
l
HDCP management including HDCP 2.2 support
l
Built-in web interface for easy configuration and monitoring
l
Compatibility with Crestron® 3-Series® or later
control systems
l
.AV Framework™ technology support
l
Crestron XiO Cloud™ service support
l
Compact surface-mount design
NOTE: Power is transmitted over the CATx cable that
connects the HD-RX-4K-510-C-E to a DM Lite transmitter.
The HD-RX-4K-510-C-E can power three transmitters
simultaneously.
In addition to three DM Lite inputs, the HD-RX-4K-510-C-E
provides two HDMI inputs that can be connected to local
AVsources.
Automatic Switching of Inputs
Automatic switching among the DM Lite and HDMI inputs can
occur based on the last connected input. Switching behavior is
configurable using the web interface or programmable using a
Crestron control system. In addition, input selection push
buttons on the front panel of the HD-RX-4K-510-C-E allow the
desired input to be selected manually.
HDMI Output with 4K Scaler
A single HDMI output with a built-in scaler connects to a display
or other device with an HDMI input.2Input resolutions are
automatically scaled to match the native resolution of the
display device, resulting in optimal image quality. For
applications requiring comprehensive EDID management, the
web interface can be used to ensure that every input is
displayed at its optimal resolution and format. Input resolutions
up to 4K60 4:2:0 are supported.
Enhanced Audio Capabilities
The HD-RX-4K-510-C-E includes a built-in amplifier that can
drive a pair of 4- or 8-ohm stereo speakers (25 W per channel).
TheHD-RX-4K-510-C-E also provides 6x2 audio mixing
capability. Embedded HDMI 2-channel LPCM audio can be
extracted from the selected DM Lite or HDMI input and
combined with the five analog audio inputs (LINE 1, LINE 2,
MIC1, MIC2, and AUX). Gain and mute sound adjustments can
be made to each of the six inputs being mixed. The mixed audio
is then transmitted as two audio outputs: one mirrored AUX 1,
SPEAKER, HDMI mixer output and one AUX 2 output. Audio
mixer settings such as volume and mute control are
configurable for each of the two outputs independently.
1
HD-RX-4K-510-C-E
4K Multiformat 5x1 AV Switch and Receiver
Device Control
Equipped with onboard control ports, the HD-RX-4K-510-C-E
can control various devices in a room. The COM (RS-232) port
and CEC over the HDMI output can enable the display device to
be turned on or off automatically without the use of a control
system. With the use of a control system, the IR port can also
control the display device. Two relay ports are provided for
controlling a projection screen and other low-voltage contactclosure activated equipment. Two Versiport I/O ports enable
the integration of devices such as power sensors and motion
detectors. An Ethernet port connection to a LAN also provides
control by enabling use of the built-in web interface as well as
connection to a control system.
NOTE: The IR, COM, and Ethernet ports cannot be used to
extend signals over a DM Lite connection.
.AV Framework™ Technology Support
In addition to a built-in web interface and control system
programming, the built-in .AV Framework technology of the
MPC3-201 and MPC3-302 control systems can be used to
control the HD-RX-4K-510-C-E as a switcher. (For information
about .AV Framework technology, visit
www.crestron.com/avframework.)
Crestron XiO Cloud™ Service Support
The HD-RX-4K-510-C-E is compatible with the Crestron XiO
Cloud service, which is an IoT (Internet of Things) based
platform for remotely provisioning, monitoring, and managing
Crestron devices across an enterprise or an entire client base.
The service enables installers and IT managers to deploy and
manage thousands of devices in the amount of time it would
ordinarily take to manage a single device. For more information,
visit www.crestron.com/xiocloud.
Compact Design
Compact in design, the HD-RX-4K-510-C-E can be mounted
onto a flat surface such as a wall or attached to the underside
of a table.
Specifications
Video
Switcher: 5x1 auto-switching or manual, audio-follows-video,
Crestron Auto-Locking® and QuickSwitch HD™ technologies
Scaler (HDMI Output): 4K video scaler with motion-adaptive
deinterlacing, intelligent frame rate conversion, Deep Color
support, content-adaptive noise reduction, 3:2/2:2 pull-down
detection and recovery
Input Signal Types: HDMI with Deep Color and 4K (DVI and
Dual-Mode DisplayPort™ interface compatible3) on Inputs 1-2,
DMLite with Deep Color and 4K on Inputs 3-5
Output Signal Types: HDMI with Deep Color and 4K
(DVI compatible4)
Copy Protection: HDCP 2.2
Maximum Resolutions: Common resolutions are listed below for
the HDMI and DM Lite inputs.
Scan Type Resolution
Progressive 4096x2160
DCI 4K and
3840x2160
4K UHD
2560x1600
WQXGA
1920x1080
HD 1080p
Frame
Rate
24 Hz 4:4:4 30bit
30 Hz 4:4:4 24bit
30 Hz 4:2:2 36bit
60 Hz 4:2:0 24bit
60 Hz 4:4:4 36bit
60 Hz 4:4:4 36bit
Color
Sampling
Color
Depth
NOTES:
l Custom resolutions are supported at pixel clock rates
up to 300 MHz.
l Interlaced video sources are not supported.
Scaler Output Resolutions, HDMI:
Auto (EDID preferred), 1280x720p@50Hz (720p50),
1280x720p@60Hz (720p60), 1920x1080i@25Hz (1080i25),
1920x1080i@30Hz (1080i30), 1920x1080p@30Hz
(1080p30), 1920x1080p@25Hz (1080p25),
1920x1080p@24Hz (1080p24), 1920x1080p@50Hz
(1080p50), 1920x1080p@60Hz (1080p60),
3840x2160p@24Hz, 3840x2160p@25Hz, 3840x2160p@30Hz,
4096x2160p@24Hz, 4096x2160p@25Hz, 4096x2160p@30Hz,
3840x2160p@50Hz, 3840x2160p@60Hz, 4096x2160p@50Hz,
4096x2160p@60Hz
Audio, General
Switcher/Mixer: 6x2 audio mixer:
Audio Inputs:
Two stereo 2-channel LINE inputs
Two mono 1-channel MIC inputs
One mono 1-channel AUX input
One stereo 2-channel LPCM audio extracted from
the selected HDMI or DM Lite input source
Audio Outputs:
One mirrored AUX 1, SPEAKER, and HDMI mixer output,
stereo 2-channel
One AUX 2 output, stereo 2-channel
Analog-to-Digital Conversion: 24-bit 48 kHz
Digital-to-Analog Conversion: 24-bit 48 kHz
HD-RX-4K-510-C-E
4K Multiformat 5x1 AV Switch and Receiver
Frequency Response, Analog Audio Outputs:
20 Hz to 20 kHz ±0.5 dB (AUX outputs)
20 Hz to 20 kHz @ full power ±3 dB (speaker output)
S/N Ratio, Analog Audio Outputs:
>95 dB @ 10 dBV, 20 Hz to 20 kHz, A-weighted (AUX outputs)
>90 dB @ 10 dBV, 20 Hz to 20 kHz, A-weighted (speaker
output)
THD+N, Analog Audio Outputs:
<0.005% @ 1 kHz and 10 dBV (AUX outputs)
<0.3% @ 1 kHz and 10 dBV (speaker output)
Stereo Separation, Analog Audio Outputs:
20 Hz to 20 kHz ≤80 dB (AUX outputs)
20 Hz to 20 kHz ≤60 dB (speaker output)
Audio, Microphone Inputs
Two balanced 1-channel microphone inputs (MIC 1 and MIC 2):
Input Signal Type: Mono analog
Phantom Power: +48 VDC, 12 mA, enable or disable per channel
Gain: 0 dB to +60 dB per channel in 1 dB increments
Mute: Enable or disable per channel
Audio, Line Inputs
Two balanced/unbalanced 2-channel line inputs (LINE 1 and
LINE 2):
Input Signal Type: Stereo analog
Balanced Line Input Level: 4 Vrms
Unbalanced Line Input Level: 2 Vrms
Line Input Impedance: >10k ohms
Audio, Auxiliary Input
One balanced 1-channel auxiliary input (AUX):
Input Signal Type: Mono analog
Balanced Line Input Level: 4 Vrms
Line Input Impedance: >10k ohms
Audio, Source Inputs
Two HDMI and three DM Lite inputs (HDMI 1-2 and DM Lite
3-5):
Input Signal Types: HDMI (Dual-Mode DisplayPort interface
compatible), DM Lite
Digital Formats: 2-channel LPCM
Audio Outputs
One mirrored SPEAKER, HDMI, and balanced/unbalanced
AUX 1 mixer output:
Output Signal Type/Format: Stereo 2-channel
AUX 1 Output Impedance: 200 ohms balanced, 100 ohms
unbalanced
AUX 1 Maximum Output Level: 4 Vrms balanced, 2 Vrms
unbalanced
Selected Source: -80 dB to +20 dB level adjustment range
plus Mute
MIC 1-2: -80 dB to +20 dB level adjustment range plus Mute
LINE 1-2: -80 dB to +20 dB level adjustment range plus Mute
AUX: -80 dB to +20 dB level adjustment range plus Mute
Master Volume: -80 dB to +20 dB level adjustment range
plusMono
Amplifier Output Power: 25 W RMS per channel @ 8 ohms,
4 ohms tolerant
Amplifier Power: On or off
Mute: Enable or disable independently for AUX 1, SPEAKER,
and HDMI mixer output
One balanced/unbalanced AUX 2 output:
Output Signal Type/Format: Stereo 2-channel
Output Impedance: 200 ohms balanced, 100 ohms unbalanced
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
Selected Source: -80 dB to +20 dB level adjustment range
plus Mute
MIC 1-2: -80 dB to +20 dB level adjustment range plus Mute
LINE 1-2: -80 dB to +20 dB level adjustment range plus Mute
AUX: -80 dB to +20 dB level adjustment range plus Mute
Master Volume: -80 dB to +20 dB level adjustment range
plus Mono
Mute: Enable or disable for AUX 2
Communications
Ethernet: 100/1000 Mbps, auto-switching, auto-negotiating,
auto-discovery, full/half duplex, CIP, DHCP, web browser setup
and control
RS-232: 2-way device control and monitoring up to 115.2k baud
with hardware and software handshaking
IR: 1-way device control via infrared up to 60 kHz
HDMI: HDCP 2.2, EDID, CEC
DM Lite: HDCP 2.2, EDID
Connectors
L/R, LINE INPUT 1-2: (2) 5-pin 3.5 mm detachable terminal
blocks
MIC INPUT 1-2: (2) 3-pin 3.5 mm detachable terminal blocks
AUX INPUT: (1) 3-pin 3.5 mm detachable terminal block
HD-RX-4K-510-C-E
4K Multiformat 5x1 AV Switch and Receiver
HDMI INPUT 1-2: (2) HDMI Type A connectors, female;
HDMI digital video/audio inputs;
DVI and Dual-Mode DisplayPort interface compatible
DM Lite INPUT 3-5: (3) 8-pin RJ-45 yellow connectors, female,
shielded;
DM Lite input ports for connection to DM Lite transmitters
L/R, AUX OUT 1-2: (2) 5-pin 3.5 mm detachable terminal blocks
HDMI OUTPUT: (1) HDMI Type A connector, female;
HDMI digital video/audio output;
DVI compatible
NOTE: CEC over the HDMI output provides Power On/Off
control of the display device without a control system or full
programmable control of any device with a control system.
Ethernet: (1) 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port
SPEAKER OUTPUT: (2) 2-pin 7.62 mm reversed gender 20 A
detachable terminal blocks, power amplifier outputs;
Wire Size: Terminals accept up to 12 AWG (3.31 mm);
Output is direct-coupled—not transformer isolated
I/O 1-2: (2) 2-pin detachable terminal blocks;
Comprise 2 Versiport digital input/output or analog input ports
(referenced to GND);
Digital Input: Rated to 0-24 VDC, input impedance 20k ohms,
logic threshold >3.125 V low/0 and <1.875 V high/1;
Digital Output: 250 mA sink from maximum 24 VDC, catch
diodes for use with real world loads;
Analog Input: Rated for 0-10 VDC, protected to 24 VDC
maximum, input impedance 21k ohms with pull-up resistor
disabled;
Programmable 5 V, 2k ohms pull-up resistor per pin
RLY 1-2: (2) 2-pin detachable terminal blocks;
Comprise 8 normally open, isolated relays;
Rated 1 A, 30 VAC/VDC;
MOV arc suppression across contacts
IR: (1) 2-pin 3.5 mm detachable terminal block;
IR output control port; supports IR up to 60 kHz;
IRP2 emitter sold separately
4
2
3
100-240V 4A-2A 50/60 Hz: (1) IEC 60320 C14 mains power
inlet;
Mates with removable power cord, included
NOTE: This power connection powers both the
HD-RX-4K-510-C-E and all connected DM Lite transmitters.
Whenconnected to the HD-RX-4K-510-C-E, DM Lite
transmitters must not be connected to power.
SERVICE: (1) USB Type A connector, female;
For factory use only
Controls and Indicators
PWR: (1) LED, indicates that power is being applied to the
HD-RX-4K-510-C-E. Amber indicates that the device is booting.
Green indicates that the device is operational.
INPUT 1-5: (5) Push buttons for manual input selection and
(5) LEDs. Green indicates that video is switched. Amber
indicates that video is detected but is not switched.
AUTO: (1) Push button to enable or disable automatic
switching, and (1) green LED to indicate that automatic
switching is enabled
SETUP: (1) Red LED and (1) push button for display of IP
address on the HDMI output
DM Lite: (2) LEDs on RJ-45 connector. Green indicates that a
DM Lite link is established. Flashing amber indicates non-HDCP
video and solid amber indicates HDCP video.
Ethernet: (2) LEDs on RJ-45 connector. Green indicates that an
Ethernet link is established. Flashing amber indicates Ethernet
activity.
Power
Mains Power: 4 A - 2 A @ 100-240 VAC, 50/60 Hz
NOTE: The AC mains power connection powers both the
HD-RX-4K-510-C-E and all connected DM Lite transmitters.
When connected to the HD-RX-4K-510-C-E, DM Lite
transmitters must not be connected to power.
NOTE: The IR port provides Power On/Off control of the
display device with the use of a control system.
COM: (1) 5-pin 3.5 mm detachable terminal block;
Bidirectional RS-232 port;
Supports RS-232 up to 115.2k baud with hardware and software
handshaking
NOTE: The COM port provides Power On/Off control of the
display device without a control system or full
programmable control of any device with a control system.
Environmental
Temperature: 32° to 104° F (0° to 40° C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Chassis: Metal, black finish, vented sides, 2 mounting flanges
attached
Mounting: Surface mount
HD-RX-4K-510-C-E
4K Multiformat 5x1 AV Switch and Receiver
Dimensions
Height: 10.22 in. (260 mm)
Width: 14.18 in. (361 mm) with mounting flanges attached
Depth: 1.74 in. (45 mm)
Weight
7.5 lb (3.4 kg) with mounting flanges attached
Compliance
UL® Listed for US and Canada, CE, IC, FCC Part 15 Class B
digitaldevice
Model and Accessories
Model
HD-RX-4K-510-C-E: 4K Multiformat 5x1 AV Switch and
Receiver
Available Accessories
For supported accessories, visit the HD-RX-4K-510-C-E
product page at www.crestron.com.
This product may be pu rchased from an au thorized Crestron dealer. To find a
dealer, please contact the Crestron sales representative for your area. A list of
sales representatives is available online at
www.crestron.com/How-T o-B uy/ Find-a-Representative or by calling
855-263-8754.
The specific patents that cover Crestron products are listed online at
www.crestron.com/legal/patents.
Certain Crestron produ cts con tain open source software. Fo r specific
information, visitwww.crestron.com/o pensource.
Crestron, the Crestron logo, .AV Framework, 3-Series, Au to-Lo cking, Crestron
XiO Cloud, DigitalMedia, DigitalMedia 8G+, DM Lite, an d QuickSwitch HD are
either trademarks or registered trademarks of Crestron Electronics, Inc. in the
United States and/ or other countries. DisplayPort is either a trademark or
registered trademark of Video Standards Association in the United States
and/ or other countries. HDBaseT is either a trademark or registered trademark
of the HDBaseT Alliance in the United States and/or other cou ntries. HDMI and
the HDMI logo are either trademarks or registered trademarks of HDMI
Licensing LLC in the United States and/or other cou ntries. UL is either a
trademark or registered trademark of Underwriters Laboratories, Inc. in the
United States and/ or other countries. Othertrademarks , registered
trademarks, and trade names may be used in this document to refer to either
the entities claiming the marks and names or their produ cts. Crestron disclaims
any proprietary interest in the marks and names of others. Crestron is not
respon sible for errors in typography or photography.
Specifications are subject to change without notice.
©2019 Crestron Electronics, Inc.
Rev 11/ 22/19
Notes:
1. For DM Lite con nections, use Crestron DM-CBL-8G, Crestron
DM-CBL-ULTRA, or third-party CAT5e or higher cable. To safeguard
against unpredictable environmental electrical noise that may impact
performan ce at resolutions above 1080p, shielded cable and connectors
are recommended for all applications and are required when bundling
multiple cables in a wire run. Wireand cables sold separately. DM Lite ports
are not compatible with DigitalMedia 8G+®, HDBas eT®, PoE,or PoDM
technology or any other type of CATx based interface or network.
2. For information about compatibility of the HDMI output with Crestron
HDMI extenders, refer to Online Help Answer ID 10 00503 on the Crestron
website (www.crestron.com).
3. The HDMI inpu t requires an appro priate adapter or interface cable to
accommodate a DVI or Dual-Mode DisplayPort signal. CBL-HDI-DVI
interface cables are available separately.
4. The HDMI ou tput requires an appropriate adapter or interface cable to
accommodate a DVI signal. CBL-HDI-DVI interface cables are available
separately.
HD-RX-4K-510-C-E
4K Multiformat 5x1 AV Switch and Receiver
Loading...