HD-EXT4-C
4K HDMI® over HDBaseT® Extender w/Analog Audio
> HDBaseT® Certified 4K Ultra HD signal extender
> Extends uncompressed digital video, audio, and control
signals over a single CAT type twisted pair cable
> Supports cable lengths up to 330 ft (100 m) for all
resolutions up to 4K and Ultra HD using DM® Ultra cable
> Supports cable lengths up to 330 ft (100 m) for 1080p,
WUXGA, and 2K using DM 8G® cable or CAT5e
> Supports cable lengths up to 230 ft (70 m) for 4K and UHD
using DM 8G cable, or 165 ft (50 m) using CAT5e
> Can also extend a stereo analog audio signal via a
second cable
> Compatible with HDMI®, DVI, and DisplayPort Multimode
sources
> Compatible with HDMI and DVI display devices
> Supports Dolby® TrueHD, DTS-HD®, and uncompressed
7.1 linear PCM audio
> HDCP 2.2 compliant
> Passes CEC and EDID
> 24VDC power pack included
> Available in white or black
> No programming or configuration required
[2]
[3]
[1]
[1]
[1]
[1]
[3]
Shown with
surface mount
bracket attached
The Crestron® 4K HDMI® over HDBaseT® Extender (HD-EXT4-C) delivers
a professional-grade digital HD AV signal extension solution for use in the
home, classroom, auditorium, or corporate boardroom. Without any special
setup or configuration, the HD-EXT4-C enables the transmission of ultra
high-definition digital video and audio over wire runs up to 330 feet
(100 meters) using a single CAT type twisted pair cable. For applications
that include an analog audio signal, the HD-EXT4-C can also handle
stereo line-level audio over a second cable.
[1,2]
NOTE: The HD-EXT4-C is composed of one HD-TX4-C transmitter and
one HD-RX4-C receiver. These components are only sold as part of the
HD-EXT4-C package.
4K Ultra HD Signal Extension
Using HDBaseT technology, the HD-EXT4-C allows for the extension of
uncompressed HDMI signals over a single CAT type twisted pair cable. In
addition to HDMI, it is also compatible with DVI and DisplayPort Multimode
sources, and DVI display devices.
[2]
Without relying on signal-degrading
compression or inferior HDMI signal boosting, HDBaseT reliably transports
the full resolution signal from source to display — intact and
uncompromised.
The HD-EXT4-C handles uncompressed Full HD 1080p, Ultra HD, 2K,
and 4K video signals with support for 3D, Deep Color, and HDCP 2.2.
Audio capabilities include support for high-bitrate 7.1 audio formats like
Dolby® TrueHD and DTS-HD Master Audio™ as well as uncompressed
linear PCM. All signals are transported over a single CAT type cable,
supporting 1080p, WUXGA, and 2K signals at distances up to 330 feet
(100 m) using Crestron DM® Ultra or DM 8G® Cable, or third-party CAT5e.
Higher resolutions up to UHD and 4K are supported at distances up to 330
feet (100 m) using DM Ultra Cable, 230 feet (70 m) using DM 8G Cable, or
165 feet (50 m) using CAT5e.
[1]
Legacy Audio Device Support
In addition to carrying digital video and audio, the HD-EXT4-C also provides
for the extension of an analog audio signal to support DVI devices (and
certain HDMI devices) that may not include or support an embedded digital
audio channel. Enabling the extension of analog audio simply requires an
additional twisted-pair type cable.
[2]
Uncompromised and Uncomplicated
Crestron HDMI over HDBaseT products afford a very dependable signal
extension solution that’s simple to implement. No special configuration
or programming is required — just connect your source and display and
enjoy high-quality video and audio from across the room — or the other
end of the house.
The HD-EXT4-C is composed of one transmitter and one receiver
(HD-TX4-C and HD-RX4-C, both included). The transmitter can be mounted
in a single-gang wall box, or attached to any flat surface or inside an
equipment rack. The compact receiver can be mounted discreetly behind
a display device or wherever else it needs to go. Linking the two
components requires just one or two CAT type cables.
[1,2]
Crestron offers
the cable and connectors for a complete, easy, and reliable wiring solution.
A range of professional AV interface cables and wall plates is also available
to complement the HD-EXT4-C for a total custom installation solution.
crestron.com | 800.237.2041
HD-EXT4-C 4K HDMI
HD-TX4-C-B – Front & Rear View
HD-EXT4-C-B SYSTEM (Includes HD-TX4-C-B & HD-RX4-C-B)
®
over HDBaseT® Extender w/Analog Audio
HD-RX4-C-B – Top, Front & Rear View
SPECIFICATIONS
Maximum HDBaseT® Cable Lengths
Cable Type:
Resolution:
1080p60 Full HD
1920x1200 WUXGA
1600x1200 UXGA
2048x1080 2K DCI
2560x1440 WQHD
2560x1600 WQXGA
3840x2160 Ultra HD
4096x2160 4K DCI
Video
Maximum Resolutions:
Scan
Type
Progressive
1920x1080 HD1080p 60 Hz 4:4:4 36 bit
Interlaced 1920x1080 HD1080i 30 Hz 4:4:4 36 bit
NOTE: Common resolutions are shown; other custom resolutions are
supported at pixel clock rates up to 300 MHz
DM-CBL-ULTRA
DM® Ultra
Cable
DM-CBL-8G
DM 8G®
Cable
330 ft
(100 m)
CAT5e
(or better)
UTP or STP
330 ft
(100 m)
330 ft
(100 m)
Resolution
(70 m)
Frame
Rate
230 ft
Color
Sampling
165 ft
(50 m)
Color
Depth
24 Hz 4:4:4 30 bit
4096x2160 4K DCI
&
3840x2160 Ultra HD
30 Hz 4:4:4 24 bit
30 Hz 4:2:2 36 bit
60 Hz 4:2:0 24 bit
2560x1600 WQXGA 60 Hz 4:4:4 36 bit
Input Signal Types: HDMI® w/Deep Color, 3D, & 4K (DVI & DisplayPort
Multimode compatible
Output Signal Types: HDMI w/Deep Color, 3D, & 4K (DVI compatible
Audio
[1]
Input Signal Types: HDMI (DisplayPort Multimode compatible
[3]
)
[3]
)
[3]
),
analog stereo
Output Signal Types: HDMI, analog stereo
Formats, HDMI: Dolby Digital®, Dolby Digital EX, Dolby Digital Plus,
Dolby® TrueHD, DTS®, DTS-ES, DTS 96/24, DTS-HD High Res,
DTS-HD Master Audio™, LPCM up to 8 channels
Formats, Analog: Stereo 2-channel
Performance (analog): Frequency Response: 20Hz to 20kHz ±0.25dB;
S/N Ratio: >93dB, 20Hz to 20kHz A-weighted;
THD+N: 0.01% @ 20Hz to 20kHz;
Stereo Separation: >85dB
Communications
HDMI: Passes HDCP 2.2, EDID, & CEC
Connectors – HD-TX4-C Transmitter
HDMI IN: (1) 19-pin Type A HDMI female;
HDMI digital video/audio input;
Also supports DVI or Displayport Multimode
[3]
AUDIO IN: (1) 3.5mm TRS mini phone jack;
Unbalanced stereo line-level audio input;
Maximum Input Level: 2 Vrms;
Input Impedance: 15k Ohms
AUDIO OUT L, R (rear): (1) 5-pin 3.5mm detachable terminal block;
Connects to the AUDIO IN port of the HD-RX4-C receiver via a dedicated
STP or UTP cable
[2]
crestron.com | 800.237.2041
HD-EXT4-C 4K HDMI
®
over HDBaseT® Extender w/Analog Audio
HD-TX4-C-B w/Surface Mount Bracket HD-TX4-C-B & HD-RX4-C-B Attached to Rack Rails
Ground (rear): (1) Flying lead, chassis ground connection
HDBaseT OUT (rear): (1) 8-pin RJ45 female, shielded;
Connects to the HDBaseT IN port of the HD-RX4-C receiver via CAT5e,
Crestron DM-CBL-8G, or Crestron DM-CBL-ULTRA cable
Connectors – HD-RX4-C Receiver
[1]
AUDIO OUT: (2) RCA female;
Unbalanced stereo line-level audio output;
Maximum Output Level: 1.85 Vrms;
Output Impedance: 100 Ohms
G: (1) 6-32 screw, chassis ground lug
HDMI OUT: (1) 19-pin Type A HDMI female;
HDMI digital video/audio output;
Also supports DVI
[3]
HDBaseT IN: (1) 8-pin RJ45 female, shielded;
Connects to the HDBaseT OUT port of the HD-TX4-C transmitter via CAT5e,
Crestron DM-CBL-8G, or Crestron DM-CBL-ULTRA cable
[1]
AUDIO IN R, L: (1) 5-pin 3.5mm detachable terminal block;
Connects to the AUDIO OUT port of the HD-TX4-C transmitter via a
dedicated STP or UTP cable
[2]
PWR 24VDC 0.75A: (1) 2.1 x 5.5 mm DC power connector;
24 Volt DC power input (PW-2407WU power pack included)
Controls & Indicators – HD-TX4-C Transmitter
PWR/LINK: (1) dual-color amber/green LED, indicates operating power
supplied via HD-RX4-C
[4]
, and indicates HDBaseT link status and HDMI
input signal presence
HDBaseT OUT (rear): (2) LEDs, green LED indicates link status, amber LED
indicates video and HDCP signal presence
SW1 (side): (1) slide switch, enables hot plug detect
Indicators – HD-RX4-C Receiver
PWR: (1) green LED, indicates operating power supplied via local
power pack
HDBaseT IN: (2) LEDs, green LED indicates link status, amber LED
indicates video and HDCP signal presence
Power Requirements
Power Pack: 0.75 Amp @ 24 Volts DC;
100-240 Volts AC, 50/60 Hz power pack, model PW-2407WU, included
Environmental
Temperature: 32° to 104°F (0° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: HD-TX4-C: 2 BTU/hr;
HD-RX4-C: 11 BTU/hr
Enclosure – HD-TX4-C Transmitter
Construction: Metal, black finish with white or black polycarbonate
label overlay
Flush Wall Mount: 1-gang mountable in an extra-deep electrical box
(2-1/2 inch deep minimum), requires decorator style faceplate
(not included)
Surface Mount: Surface mount bracket included
Rack Mount: Attachable to a single 19-inch EIA rack rail
Enclosure – HD-RX4-C Receiver
Construction: Aluminum w/polycarbonate label overlay and (4) integral
mounting flanges
Mounting: Freestanding, surface mount, or attach to a single rack rail
[4]
crestron.com | 800.237.2041
HD-EXT4-C 4K HDMI
®
over HDBaseT® Extender w/Analog Audio
Dimensions
HD-TX4-C Transmitter: Height: 4.12 in (105 mm);
Width: 1.72 in (44 mm);
Depth: 2.38 in (61 mm)
HD-RX4-C Receiver: Height: 1.43 in (37 mm);
Width: 3.91 in (100 mm);
Depth: 4.85 in (124 mm)
Weight
HD-TX4-C Transmitter: 5.8 oz (165 g)
HD-RX4-C Receiver: 11.6 oz (330 g)
MODELS & ACCESSORIES
Available Models
HD-EXT4-C-B_SYSTEM: 4K HDMI® over HDBaseT® Extender w/Analog
Audio, Black
HD-EXT4-C-W_SYSTEM: 4K HDMI® over HDBaseT® Extender w/Analog
Audio, White
Included Accessories
PW-2407WU: Wall Mount Power Pack 24VDC, 0.75A, Universal
(Qty. 1 included)
Available Accessories
DM-CBL-ULTRA-NP: DigitalMedia™ Ultra Cable, Non-Plenum Type CMR
DM-CBL-ULTRA-P: DigitalMedia™ Ultra Cable, Plenum Type CMP
DM-CBL-ULTRA-LSZH: DigitalMedia™ Ultra Cable, Low Smoke Zero
Halogen
DM-CONN: Connector for DM-CBL-ULTRA
DM-CBL-8G-NP: DigitalMedia 8G™ Cable, non-plenum
DM-CBL-8G-P: DigitalMedia 8G™ Cable, plenum
DM-8G-CONN-WG: Connector with Wire Guide for DM-CBL-8G
DM-8G-CRIMP-WG: Crimping Tool for DM-8G-CONN-WG
DM-8G-CONN: Connector for DM-CBL-8G
DM-8G-CRIMP: Crimping Tool for DM-8G-CONN
CBL Series: Crestron® Certified Interface Cables
MP-WP Series: Media Presentation Wall Plates
MPI-WP Series: Media Presentation Wall Plates - International Version
Notes:
1. The maximum cable length for HDBaseT is dependent upon the type of cable and resolution
of the video signal. Refer to the “Maximum HDBaseT Cable Lengths” table for a detailed
overview. Shielded cable and connectors are recommended to safeguard against unpredictable
environmental electrical noise which may impact performance at resolutions above 1080p. All
wire and cables are sold separately.
2. For the balanced analog “AUDIO” connection between the HD-TX4-C transmitter and
HD-RX4-C receiver, use dual-twisted pair shielded audio cable or quality CAT5 (or better) UTP
or STP. Crestron DM-CBL-8G DigitalMedia 8G Cable is recommended.
3. HDMI IN requires an appropriate adapter or interface cable to accommodate a DVI or
DisplayPort Multimode signal. HDMI OUT requires an appropriate adapter or interface cable to
accommodate a DVI signal. CBL-HD-DVI interface cables are available separately.
4. The power pack must be connected to the HD-RX4-C receiver. Power is passed to the
HD-TX4-C transmitter via the HDBaseT connection. Please note, the HD-TX4-C and HD-RX4-C
are not PoH compatible. They cannot be powered by, or supply power to, another HDBaseT
device. They may however be connected to such devices without risk of malfunction.
This product may be purchased from an authorized Crestron dealer. To find a dealer, please
contact the Crestron sales representative for your area. A list of sales representatives is available
online at www.crestron.com/salesreps or by calling 800-237-2041.
The specific patents that cover Crestron products are listed online at: patents.crestron.com.
Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G, DM, and DM 8G are either trademarks
or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
Dolby and Dolby Digital are either trademarks or registered trademarks of Dolby Laboratories in
the United States and/or other countries. DTS, DTS-HD, and DTS-HD Master Audio are either
trademarks or registered trademarks of DTS, Inc. in the United States and/or other countries.
HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the
HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI Logo are
either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or
other countries. Other trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their products. Crestron
disclaims any proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography. Specifications are subject to change without notice.
©2015 Crestron Electronics, Inc.
crestron.com | 800.237.2041
HD-EXT4-C 4K HDMI
®
over HDBaseT® Extender w/Analog Audio
crestron.com | 800.237.2041
HD-EXT4-C 4K HDMI
®
over HDBaseT® Extender w/Analog Audio
Crestron Electronics, Inc. 15 Volvo Drive | Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 | Fax: 201.767.1903
www.crestron.com
All brand names, product names and trademarks are the property of their respective owners.
Specifications subject to change without notice. Revised 06/15/15
©2015 Crestron Electronics, Inc.
Loading...