Page 1
DO GUIDE
HD-DAx-4KZ-E Series
4K60 4:4:4 HDR Distribution Ampliers
DO Check the Box
QTY ITEM PART NUM.
1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2037209
DO Install the Device
The Crestron® HD-DAx-4KZ-E Series consists of the HD-DA2-4KZ-E, HD-DA4-4KZ-E, and
HD-DA8-4KZ-E. The devices can be mounted onto a at surface or onto a rack rail.
Mount onto a Flat Sur face
Using four mounting screws (not included), mount the device onto a at surface such as a wall.
Wall Mounting (HD-DA2-4KZ-E Shown)
Mount onto a Rack Rail
Mount the device onto a front or rear rail of a rack. Position either the left or right mounting ange of
the device so that the holes align with the holes in the rack. Then, secure the device to the rack using
two rack mounting screws (not included).
Rail Mounting (HD-DA2-4KZ-E Shown)
DO Connect the Device
Connect the device as required for the application.
Front Panel Connections (HD-DA2-4KZ-E Shown)
INPUT:
From HDMI®
audio/video
source
OUTPUT 1:
To HDMI
display
OUTPUT 2:
To HDMI
display
SERVICE:
For rmware
loading
24 V 0.75 A:
From included
power pack
DO Select the EDID Mode
Select the EDID (Extended Display Identication Data) mode by moving the EDID switch to either
of the following positions:
• DEFAULT: (Default setting) The device sends a predened Crestron EDID to the
input device. The Crestron EDID supports 2-channel LPCM audio and
4K60 444 non-HDR video.
• COPY 1ST: The device copies the EDID of the display connected to OUTPUT 1 and
sends the EDID to the input device.
NOTE: If the display that is connected to OUTPUT 1 is disconnected, the current EDID
is retained. Connecting a different display to OUTPUT 1 does not automatically update
the EDID at the input device. To update the EDID, move the EDID switch to the DEFAULT
position and then back to the COPY 1ST position.
EDID Selection Switch (HD-DA2-4KZ-E Shown)
Page 2
DO Select the HDCP Version
Select the HDCP version by moving the HDCP switch to one of the following positions:
• OFF: Disables HDCP support
• 1.4: Sets the HDCP version to 1.4
• 2.2: (Default setting) Sets the HDCP version to 2.2
HDCP Selection Switch (HD-DA2-4KZ-E Shown)
DO Observe the LEDs
Observe the LEDs on the rear panel of the device:
• PWR: Lights amber to indicate that the device is booting, and lights green to indicate that
the device is powered on
• IN P U T: Lights green to indicate that an HDMI signal is detected at the HDMI input
• OUTPUT 1-2, 1-4, or 1-8: Lights green to indicate that the corresponding HDMI output is
transmitting an HDMI signal
In addition to the LEDs listed above, a SETUP LED is also provided. When the SETUP button is
pressed for 10 seconds, the SETUP LED ashes red ten times to indicate that the default settings
have been restored.
Rear Panel LEDs (HD-DA2-4KZ-E Shown)
DO Learn More
Visit the website for additional information and
the latest rmware updates. To learn more about
this product, use a QR reader application on your
mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
HD-DA2-4KZ-E
HD-DA4-4KZ-E HD-DA8-4KZ-E
As of the date of manufactur e, the pro duct ha s been te sted an d found to c omply with specications for CE mark ing.
Federal Communications Commission (FCC) Compliance Statement
This device complies with par t 15 of the FCC Rules. Operation is subject to the followin g two con ditions:
(1) This devic e may not ca use har mful interfe rence, and (2) thi s device m ust acc ept any interference recei ved, including interferenc e
that may cause undesired operation.
CAUTION: Changes or modic ations not expressly a pproved by the manufacturer responsible for complia nce could void th e
user’s authorit y to operate the equipme nt.
NOTE: This equipm ent has b een tes ted and found to comply with the limi ts for a Class B digital device, pur suant to part 15 of th e
FCC Rules. These limits a re desi gned to provide reasonable protection again st harmful inte rference in a reside ntial installation.
This equipment generates, u ses and c an radi ate radi o frequ ency energy an d, if not in stalled and us ed in accordance with the
instruction s, may cause harmful interference to r adio communic ations. However, the re is no guarante e that interfe rence w ill not
occur in a particular i nstal lation.
DO GUIDE
If this equipment does cause harmful interference to radio or television rec eption, which c an be determined by turning the
equipment off and on, th e user is encouraged to try to correct the inter ference by one o r more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the se parat ion bet ween the equipment and receiver.
• Connect the equipment into an ou tlet on a circuit different fro m that to which the re ceiver is connected.
• Consult the dea ler or an experi enced radio/ TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The speci c patents that c over Crestron pro ducts are listed a t www.crestron.com/legal/patents.
The produ ct warranty ca n be found at www.crestron.com/legal/sales-terms-conditions-warranties.
Certa in Crestron pro ducts contain op en source soft ware. For speci c information, vi sit www.crestron.com/legal/open-source-software.
Crestr on and the Cr estron lo go are eith er tradema rks or regis tered tr ademarks o f Crestro n Electr onics, Inc ., in the Unit ed State s and/or ot her count ries. HDM I and the HDMI logo ar e either
trademar ks or regis tered tra demarks of H DMI Lic ensing LL C in the Unite d States a nd/or oth er countr ies. Othe r trademar ks, regis tered tra demarks, a nd trade nam es may be used in t his
document t o refer to either t he entities claim ing the marks and na mes or their produ cts. Crestr on disclaims any pr oprietary i nterest in the ma rks and names of ot hers. Crest ron is not respon sible
for error s in typography o r photography.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2018 Crestron Electronics, Inc.
DOC. 82 76A (2 050 984 ) 04.18
Specic ations subject to c hange without not ice.
Loading...