Crestron HBK-6000 & SMK-6000
Hatchback and Swivel Mount Kits
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2002 Crestron Electronics, Inc.
Crestron HBK-6000 & SMK-6000 Hatch Back and Swivel Mount Kits
Hatchback and Swivel Mount
Kits: HBK-6000 & SMK-6000
Description
The Hatchback and Swivel Mount Kits, HBK-6000 and SMK-6000 (each sold
separately), are designed for attachment to the Crestron
TPS-4500 tilt touchpanels.
The HBK-6000 hatchback is a sleekly designed rear-cover option that provides
cable, management, wire strain relief, and prevents unauthorized users from
disconnecting the touchpanel. The wire exit hole at the rear of the HBK-6000 is sized
to accommodate all cables that would typically be connected to the touchpanel.
These include the Crestron-furnished 10-position, Siamese, or Triamese network
cable; an off-the-shelf DB15HD VGA cable, a CAT5 Ethernet cable, and a DC
power cable from an optional PW-2420RU power supply.
The SMK-6000 swivel mount accessory reduces the chance of theft while improving
viewing convenience. The base rotates 330 degrees, mounts on the desktop, in a
lectern, or on a conference table, and accommodates surface thicknesses from
3/4-inch minimum to 1 3/8-inches maximum, using the hardware provided. The
swivel mount kit includes the same rear cover as the HBK-6000 option, which
covers the cable connections. Routing the cables down through the center of the
swivel assembly keeps the cables completely hidden from the work surface.
The SMK-6000 should not be used in combination with the TPS-XVGA RGB
Graphics Card, as it does not accommodate the size and bend-radius of a typical
off-the-shelf RGBHV cable. Instead, the TPS-XVGA-BV RGB Graphics Card
w/Balanced Video should be used. The TPS-XVGA-BV includes a special Triamese
cable, which is compact and flexible enough to use with the SMK-6000.
TPS-6000, TPS-5000, and
Supplied Hardware
The hardware supplied in the kits is listed in the following table.
Supplied Hardware of the HBK-6000 and SMK-6000 Hatchback and Swivel Mount Kits
HBK-6000 SMK-6000*
One (1) Metal Bracket One (1) Swivel Mount Assembly
One (1) Plastic Cover One (1) Metal Bracket
Four (4) Screws 4-40 X 3/16 inch One (1) Metal Plate
One (1) Plastic Cover
Sixteen (16) Screws
(4) 4-40 X 3/16-inch
(4) 6-32 X 1/4-inch
(4) 8-32 X 5/8-inch
(4) 8-32 X 1-inch
* The SMK-6000 mounting kit includes a template for preparing the mounting surface.
Installation Guide – DOC. 6111 Hatchback and Swivel Mount Kits: HBK-6000 & SMK-6000 • 1
Hatch Back and Swivel Mount Kits Crestron HBK-6000 & SMK-6000
A
S
(4)
Installation
This section provides an installation procedure for each kit. The only tools required
are #1, #2, and #3 Phillips screwdrivers.
HBK-6000 Assembly/Installation Procedure
To attach the HBK-6000 Hatch Back Kit to the TPS-4500, -5000, or -6000
Touchpanel, refer to the illustration below and perform the procedures that follow.
HBK-6000 Assembly View
crews
Plastic Cover
Metal Bracket
Mounting Holes (4)
A
Openings For
Touchpanel
Rear Feet (2)
1. If necessary, use the touchpanel position lock buttons to adjust the display
to the maximum (most vertical/upright) angle.
2. Place the touchpanel face down on a padded surface to prevent damage to
the display screen.
3. Remove the four screws from the bottom rear of the touchpanel that
correspond to the mounting holes (A) in the metal bracket.
4. Position the metal bracket on the touchpanel base (mounting holes should
align, touchpanel feet should protrude through openings provided, and
standoff posts should point toward the touchpanel). Secure the metal
bracket to the touchpanel using the four screws removed in step 3.
5. With the touchpanel in its normal position, make certain cable connections
are secure, put the plastic cover in position with the cables routed through
the rear opening. Secure the cover to the metal bracket using the four
# 4-40X 3/16-inch screws supplied.
SMK-6000 Assembly/Installation Procedure
To attach the SMK-6000 Swivel Mount Kit to the TPS-4500, -5000, or -6000
Touchpanel and install the assembly on a suitable mounting surface, refer to the
following illustrations and perform the associated procedures.
1. Prepare the mounting surface using the template provided with the kit. The
center hole for the swivel assembly should be 2.5-inches minimum;
2.6-inches maximum. Make certain to observe the “FRONT” position when
drilling the four holes for the swivel assembly standoff posts.
2. If necessary, to prevent errors when reconnecting, label and disconnect any
cables connected to the touchpanel.
3. If necessary, use the touchpanel position lock buttons to adjust the display
to the maximum (most vertical/upright) angle.
2 • Hatchback and Swivel Mount Kits: HBK-6000 & SMK-6000 Installation Guide – DOC. 6111
Crestron HBK-6000 & SMK-6000 Hatch Back and Swivel Mount Kits
4. Place the touchpanel face down on a padded surface to prevent damage to
the display screen.
5. Refer to the following illustration and remove the six screws from the
bottom rear of the touchpanel that correspond to the mounting holes (A) in
the metal bracket of the kit.
SMK-6000 Swivel Mount Kit Assembly Diagram
6. Place the metal bracket on the touchpanel base (mounting holes should
align, touchpanel feet should protrude through openings provided, and
standoff posts for the rear cover should point toward the touchpanel).
Secure the metal bracket to the touchpanel using the six screws removed in
step 5.
7. Route the cables from the interface box up through the Metal Plate, through
the mounting surface, and through the Swivel Assembly, then through the
area of the bracket shown in the figure, and connect to the appropriate
touchpanel ports. Route the cables carefully to avoid chafing.
8. Being careful to avoid damage to the cables, attach the Swivel Assembly to
the Metal Bracket, using the supplied four #6-32 X 1/4 inch screws B
through the holes in the swivel assembly into the standoff posts on the
bracket. Make certain the cables are not twisted or crimped and have
sufficient slack at the port connections before fully tightening the screws.
Installation Guide – DOC. 6111 Hatchback and Swivel Mount Kits: HBK-6000 & SMK-6000 • 3
Hatch Back and Swivel Mount Kits Crestron HBK-6000 & SMK-6000
S
)
9. Make certain tab C is positioned to the front of the swivel assembly, and
that it is directly opposite bent tab E, and place the touchpanel and swivel
mount assembly down on the Mounting Surface.
10. Hold the Metal Plate in position under the mounting surface and secure the
assembly in place using the #8-32 screws F provided (use the 5/8-inch
screws for surfaces 3/4-inch to 1 1/8-inches thick; use the 1-inch screws for
surfaces 1 1/8 to 1 3/8 inches thick). Use screws D to adjust tension of the
swivel assembly.
11. Refer to the following illustration, put the plastic cover in position and
secure to the metal bracket using the four #4-40 X 3/16-inch screws
supplied.
SMK-6000 Swivel Mount Kit Rear Cover Assembly
crews (4
Plastic Cover
Metal Bracket
Further Inquiries
Future Updates
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876].
For assistance in your local time zone, refer to the Crestron website
(www.crestron.com
) for a listing of Crestron worldwide offices.
You can also log onto the online section of the Crestron website (www.crestron.com
to ask questions about Crestron products. First-time users will need to establish a
user account to fully benefit from all available features.
As of the date of manufacture, the HBK-6000 and SMK-6000 have been tested and
found to comply with specifications for CE marking.
As Crestron adds improvements to the HBK-6000 or SMK-6000, additional
information may be made available as manual updates. These updates are solely
electronic and serve as intermediary supplements prior to the release of a complete
technical documentation revision.
Check the Crestron website (www.crestron.com
) periodically for manual update
availability and its relevance. Updates are available from the Download | Product
Manuals section and are identified as an “Addendum” in the Download column.
)
4 • Hatchback and Swivel Mount Kits: HBK-6000 & SMK-6000 Installation Guide – DOC. 6111
Crestron HBK-6000 & SMK-6000 Hatch Back and Swivel Mount Kits
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange, or service without prior
authorization from CRESTRON. To obtain warranty service for CRESTRON
products, contact the factory and request an RMA (Return Merchandise
Authorization) number. Enclose a note specifying the nature of the problem, name
and phone number of contact person, RMA number, and return address.
2. Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped
freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J., or its authorized
subsidiaries, with RMA number clearly marked on the outside of all cartons.
Shipments arriving freight collect or without an RMA number shall be subject to
refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a
15% restocking fee, plus shipping costs, on any products returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by
CRESTRON, shipping by standard ground carrier. In the event repairs are found to
be non-warranty, return freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in
materials and workmanship under normal use for a period of three (3) years from the date of
purchase from CRESTRON, with the following exceptions: disk drives and any other moving or
rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1)
year; touchscreen display and overlay components are covered for 90 days; batteries and
incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized
CRESTRON dealer. Purchasers should inquire of the dealer regarding the nature and extent of the
dealer's warranty, if any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in
any application other than that for which it was intended, or if it has been subjected to misuse,
accidental damage, modification, or improper installation procedures. Furthermore, this warranty
does not cover any product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic
damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for
any claim made by a third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for
parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be
covered only by the unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed
or implied, nor authorizes any other party to offer any warranty, including any implied warranties
of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed
by law are limited to the terms of this limited warranty. This warranty statement supercedes all
previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered
trademark of Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft
Corporation.
Installation Guide – DOC. 6111 Hatchback and Swivel Mount Kits: HBK-6000 & SMK-6000 • 5
Crestron Electronics, Inc. Installation Guide – DOC. 6111
15 Volvo Drive Rockleigh, NJ 07647 09.02
Tel: 888.CRESTRON
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Loading...