Crestron GLPPA-KP Installation Manual

Page 1

Crestron GLPPA-KP

Secondary GLPPA-KP (Optional)

Keypad for GLPP Installation Guide

Further Inquiries

To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of Crestron world wide offices at www.crestron.com/offices.

To post a question about Crestron products, log onto Crestron's Online Help at www.crestron.com/onlinehelp. First-time users must establish a user account to fully benefit from all available features.

Future Updates

As Crestron improves functions, adds new features, and extends the capabilities of the GLPPA-KP units, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision.

Check the Crestron Web site periodically for manual update availability and its relevance. Updates are identified as an “Addendum” in the Download column.

DESCRIPTION

The GLPPA-KP is an in-wall keypad for Crestron Green Light® Power Pack (GLPP) systems, used to set and recall presets and turn on and off all loads connected to a GLPP. Installation is made easy thanks to a 2-wire, low-voltage bus, which connects the GLPPA-KP and GLPP main unit. Available in black, white, and almond, the GLPPA-KP fits almost any décor. Up to three GLPPA-KPs can be connected to a single GLPP system for multipoint control in a room.

Flexible Configuration

Two sets of button configurations accompany every GLPPA-KP: a rocker for turning on/off and dimming and a set of four pre-labeled buttons—ALL ON, ALL OFF, SCENE 1, and SCENE 2. Scenes can be adjusted by any user directly right from the keypad.

Easy Installation

Two flying leads connect the GLPPA-KP to the GLPP system via a non-polarized low-voltage bus. Use a choice of new or existing high-voltage (Class 1) or low-voltage (Class 2) wiring for quick installation.

Specifications

Specifications for the GLPPA-KP are listed in the following table.

GLPPA-KP Specificati ons

SPECIFI CATI ON DETAILS

Power Requirements 1 watt (0.05 amps @ 24 volts dc) supplied by GLPP

Environmental Temperature 32º F to 113º F (0º C to 45º C) Humidity 10% to 90% RH (non-condensing)

Enclosure Injection molded plastic, one gang mountable in a

Dimensions Height 4 1/8 in (105 mm) Width 1 3/4 in (45 mm) Depth 1 13/16 in (46 mm)

Weight 4 oz (50 g)

GLPPA-KP Dimensions

1 3/4 in

(45 mm)

over proprietary 2-wire bus

standard electrical box, requires decorator style faceplate (not supplied)

1 13/16 in

(46 mm)

WARNING: To avoid fire, shock, or death; turn off power at circuit breaker or fuse and test that power is off before wiring!

NOTES: Observe the following:

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• If you are unsure about any part of these i nstructions, consult a qua lified electrician.

Crestron Electronics, Inc. Installation Guide - DOC. 7211B 15 Volvo Drive Rockleigh, NJ 07647 (2031031) Tel: 888.CRESTRON 08.13 Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.

This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.

4 1/8 in

(105 mm)

INSTALLATION

Wiring

1. Using new or pre-existing wiring, connect the two non-polarized white wires with black stripes from the GLPP-DIM or GLPP-SW to the two wires on the keypad.

2. If a second or third GLPPA-KP is being used in the room, wire them in parallel.

Wiring the GLPPA-KP

GLPP

White/Black

Primary GLPPA-KP

Page 2

Assembling the Buttons

The GLPP-KP comes preassembled with a rocker button. If necessary, the rocker can be replaced with the four included buttons. If the rocker is going to be used, skip to "Installing into Single Gang Box." Otherwise, assemble the keypad as described in the following steps. Refer to the accompanying illustrations.

1. Remove the button assembly by squeezing the sides of the bezel near the bezel snaps.

Squeeze at Arrow Points and Pull to Remove Button Assembly

2. Remove the button from the front of the button assembly. Insert the new buttons through the front of the bezel and snap into place.

Gently Spread Frame Apart to Remove and Install Buttons

3. Attach button assembly to the device. Ensure that the LED is on the left side.

DEFAULT BUTTON FUNCTIONS

Button Tap

SCENE1

ON*

OFF*

ALL OFF

Button Double Tap

FULL ON

OFF*

FAST OFF

Button Hold

RAISE

LOWER

ALL ON

SCENE1

SCENE 2

ALL OFF

FULL ON

FAST OFF

RAISE

LOWER

The illustrations to the left show the default functions available for each physical button configuration and tap/hold actuation sequence. Tap, double tap, and hold activate various scenes depending on the GLPP-SW and GLPP-DIM settings. To determine scene settings, refer to the GLPP installation guides at www.crestron.com/manuals.

Button Tap

If using the single button rocker for a GLPP-DIM, tap the top of the button for scene 1; tap the bottom of the button for all off. If using the single button rocker for a GLPP-SW single button rocker, tap the top of the button for on and the bottom of the button for off.

For a four button configuration using a GLPP-DIM or a GLPP-SW, tap the first button for all on, the second button for scene 1, the third button for scene 2, and the last button for all off.

Button Double Tap

For double-tapping functions, tap the button twice within 0.5 seconds. If using the single button rocker for a GLPP-DIM, double tap the top of the button for full on; double tap the bottom of the button for fast off. If using the single button rocker for a GLPP-SW, double tap the bottom of the button for off. Double tapping the top of the button provides no function.

For a four button configuration using a GLPP-DIM or a GLPP-SW, double tap the first through third buttons for full on and the last button for fast off.

Button Hold

For holding functions, hold down the button for more than 0.5 seconds. If using the single button rocker for a GLPP-DIM, hold the top of the button to raise; hold the bottom of the button to lower. If using four buttons, hold the first button to raise and the last button to lower.

Buttons on a GLPP-SW have no functions when held.

Installing into Single Gang Box

Follow the procedure below to install the GLPPA-KP into a single gang electrical box. Refer to the illustration below for details.

1. Make sure the keypad is oriented properly (note the location of the LED).

2. Place the GLPPA-KP into the electrical box.

CAUTION: Excess wire pinched between the keypad and electrical box could short out. Make sure all excess wire is completely inside the electrical box and not between the box and the keypad.

3. Attach it to the electrical box using the included #6-32 x 3/4" screws.

Installing GLPPA-KP into Single Gang Box

Wall

Single Gang Electrical Box (Not Supplied)

(2) #6-32 x 3/4 in Screws

GLPPA-KP

4. Attach the desired decorator style faceplate (not supplied).

*Applicable to GLPP-SW only.

Return and Warranty Policies

Merchandise Returns / Repair Service

1. No merchandise may be returned for credit, exchange, or service without prior authorization from Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer. Only authorized Crestron dealers may contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address.

2. Products may be returned for credit, exchange, or service with a Crestron Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to Crestron, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. Crestron reserves the right in its sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any products returned with an RMA.

3. Return freight charges following repair of items under warranty shall be paid by Crestron, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser.

Crestron Limited Warranty

Crestron Electronics, Inc. warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three (3) years from the date of purchase from Crestron, with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touch screen display and overlay components are covered for 90 days; batteries and incandescent lamps are not covered.

This warranty extends to products purchased directly from Crestron or an authorized Crestron dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any.

Crestron shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. Furthermore, this warranty does not cover any product that has had the serial number altered, defaced, or removed.

This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall Crestron be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. Crestron is not liable for any claim made by a third party or made by the purchaser for a third party.

Crestron shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty.

Except as expressly set forth in this warranty, Crestron makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.

The specific patents that cover Crestron products are listed at patents.crestron.com.

Crestron, the Crestron logo, and Crestron Green Light are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.

UL and the UL logo are either trademarks or

Other